Smeg PVA750NL, PVA750, PVA750BE, PVA750D User Manual

Contents

1. Precautions for safety and use________________________ 22

2. Fitting the appliance in the top ________________________ 23

2.1 Fixing to the supporting structure _______________________________________23

2.2 Fitting the adhesive foam rubber strip____________________________________24

2.3 Fitting the fixing clips ________________________________________________24

2.4 Fitting the hob into the hole in the work-top _______________________________25

3. Electrical connection _______________________________ 26

4. Gas connection ___________________________________ 27

4.1 Bottled gas connection _______________________________________________27

4.2 Room ventilation____________________________________________________27

4.3 Combustion gas discharge ____________________________________________27

5. Adapting to different types of gas______________________ 28

5.1 Removing the hob skin _______________________________________________28

5.2 Adjusting for bottled gas ______________________________________________29

5.3 Adjusting for natural gas ______________________________________________29

5.4 Adjusting the primary air flow __________________________________________30

5.5 Reassembling the hob skin____________________________________________31

5.6 Adjusting the minimum setting for natural ga ______________________________31

5.7 Adjusting the minimum for bottled gas ___________________________________31

5.8 Hob burner layout ___________________________________________________31

5.9 Greasing the gas taps________________________________________________31

6. Description of controls ______________________________ 32

6.1 The front panel _____________________________________________________32

7. Using the hob _____________________________________ 33

7.1 Fitting the pan stands ________________________________________________33

7.2 Lighting burners with safety device______________________________________36

7.3 Practical hints for using the burners _____________________________________36

7.4 Pan diameters______________________________________________________37

8. Cleaning and maintenance __________________________ 38

8.1 Cleaning the hob____________________________________________________38

8.2 Cleaning the components_____________________________________________38

THESE INSTRUCTIONS ONLY APPLY TO THE COUNTRIES OF DESTINATION WHOSE IDENTIFICATION SYMBOLS ARE LISTED ON THE COVER OF THIS MANUAL. THIS BUILT-IN HOB IS CLASSIFIED AS CLASS 3.

INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is to check the gas supply system and install, commission and test the appliance.

INSTRUCTIONS FOR THE USER: these provide recommendations for use, a description of the controls and the correct procedures for cleaning and maintaining the appliance.

Precautions for Safety and Use

1. Precautions for safety and use

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB. ALSO KEEP THE SET OF NOZZLES PROVIDED IN A SAFE PLACE. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION: COOKING AND HEATING FOODS; ALL OTHER USES ARE TO BE CONSIDERED IMPROPER. THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN THOSE STATED ABOVE.

NEVER LEAVE PACKAGING RESIDUES UNATTENDED IN THE HOME. SEPARATE WASTE PACKAGING MATERIALS BY TYPE AND CONSIGN THEM TO THE NEAREST SEPARATE DISPOSAL CENTRE.

THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS.

THE PLUG TO BE CONNECTED TO THE POWER SUPPLY LEAD AND THE RELATIVE SOCKET MUST BE OF THE SAME TYPE AND COMPLY WITH THE RELEVANT REGULATIONS. THE POWER SUPPLY SOCKET MUST BE ACCESSIBLE EVEN AFTER THE APPLIANCE HAS BEEN BUILT-IN. NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD.

IMMEDIATELY AFTER INSTALLATION, CARRY OUT A QUICK TEST ON THE HOB FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS MANUAL. IF THE APPLIANCE FAILS TO OPERATE, DISCONNECT IT FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE. NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.

AFTER EACH USE OF THE HOB, ALWAYS CHECK THAT THE CONTROL KNOBS ARE TURNED TO "ZERO" (OFF).

NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE HOB PAN STANDS.

NEVER USE PANS OR GRIDDLE PLATES WHICH PROJECT BEYOND THE OUTSIDE EDGE OF THE HOB.

THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND MARK IS IN A VISIBLE POSITION UNDERNEATH THE CASING, ANNEXED TO THIS MANUAL AND APPLIED TO THE QUALITY CERTIFICATE.

THIS NAMEPLATE MUST NEVER BE REMOVED.

THE APPLIANCE IS INTENDED FOR USE BY ADULTS. KEEP CHILDREN AT A SAFE DISTANCE AND

NEVER ALLOW THEM TO PLAY WITH IT.

THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). THIS DIRECTIVE CONTAINS THE REGULATIONS GOVERNING THE COLLECTION AND RECYCLING OF DECOMMISSIONED APPLIANCES THROUGHOUT THE EUROPEAN UNION.

The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance and the use of non-original spare parts.

Instructions for the Installer

If the hob has to be adapted for a type of gas different from the one for which it is preset in the factory, make this adjusting before building it into the unit, following the instructions in point “5. Adapting to different types of gas”.

The procedures required below must be carried out by a skilled builder and/or joiner. The hob can be installed on various materials, including masonry, metal, solid wood and wood finished with plastic laminates, provided the material is heat-resistant (T 90° C).

2.1 Fixing to the supporting structure

Make a hole in the cabinet top with the dimensions shown here, maintaining a distance of at least 50 mm from the rear edge. This appliance may be installed against walls higher than the worktop surface, provided the distance shown here is maintained, in order to prevent damage due to overheating. Make sure that there is at least 750 mm between the hob burners and a shelf or hood (if any) placed vertically above them.

2. Fitting the appliance in the top

If the hob is installed above an oven, the oven must be fitted with a cooling fan.

If the hob is installed above a cupboard with doors, a separator panel must be installed underneath it. Leave a gap of at least 10 mm between the bottom of the hob and the surface of the panel, which must be easily removable to allow sufficient access for any servicing procedures.

Instructions for the Installer

2.2 Fitting the adhesive foam rubber strip

Fit the adhesive foam rubber strip (supplied with the hob) around the outside edge of its surround. It will act as a cushion between the surface of the surround and that of the cabinet. The diagram on the right shows the correct position for the foam rubber strip. Take great care when fitting it to ensure that it does not project

beyond the outside edge of the frame.

2.3 Fitting the fixing clips

Fit the fixing clips in all the points marked with an arrow. The clips fix the hob an ensure that it is centred correctly.

To fit the clips to the hob, simply press them gently horizontally into the groove provided (fig. A). Then turn them upwards to fix them permanently in place (fig. B).

Instructions for the Installer

2.4 Fitting the hob into the hole in the work-top

Take special care when fitting the hob into the work-top. If the procedures are not carried out correctly, exactly as described, the hob may be damaged.

Before fitting the hob, remove the pan stands (if fitted) and the burners from the hob.

When fitting the hob, first rest the surround entirely on the back edge of the hole in the work-top. Do not apply leverage to the surround; since this part is very delicate there is a risk of damaging it. Then lower the front of the hob until the appliance is completely in place.

Instructions for the Installer

3. Electrical connection

Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed.

The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. Check that the power supply line is properly earthed.

Pass the power supply cable through the rear of the cabinet, taking care that it does not touch the bottom case of the hob, or the oven (if any) built in underneath it.

The appliance's power supply line must be fitted with an omnipolar breaking device with contact gap of at least 3 mm, located in an easily accessible position close to the appliance itself.

The use of reductions, adapters or junctions is not recommended.

If the power supply cable has to be replaced, the gauge of the wires in the new cable must be at least 0.75 mm2 (3 x 0.75 cable), bearing in mind that the earth wire (yellow-green) must be at least 20 mm longer at the end for connection to the appliance. Use only a type H05V2V2-F or similar cable resistant to a temperature of up to 90°C. The cable must be replaced by a qualified electrician, who must make the mains connection as shown below.

L = brown N = blue

= yellow-green

The power supply lead must be replaced by an authorised service centre to prevent all risks.

The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance.

+ 12 hidden pages