Smeg PU106, PU75, PU64 User Manual
Table of Contents
1. IMPORTANT SAFETY INSTRUCTIONS ................................................................................. 4
2. COOKTOP MEASUREMENTS ............................................................................................... 5
3. POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS .................................... 6
3.1 Gas supply requirements ................................................................................................................................ 8
3.2 Electrical requirements .................................................................................................................................... 9
4. INSTALLING THE COOKTOP ............................................................................................... 11
5. CHECKING OPERATION ...................................................................................................... 14
6. WIRING DIAGRAMS .............................................................................................................15
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is able to
install, commission and test the appliance
3
Important Safety Instruction
1. IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS – Your Safety And the Safety of Others Are Very Important.
We have provided many important safety messages throughout this manual and on your appliance.
Read all instructions before using your appliance and always obey all safety messages.
RECOGNIZE SAFETY INFORMATION
This is a safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and
others.
UNDERSTAND SIGNAL WORDS
A signal word – DANGER, WARNING, or CAUTION – is used with the safety-alert symbol. DANGER
identifies the most serious hazards. It means you can be killed or seriously injured if you do not
immediately
follow instructions. CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
follow instructions. WARNING means you can be killed or seriously injured if you do not
All safety messages will inform you as to potential hazards, inform you on how to reduce the risk of
injury and as to what can occur if the instructions are not followed.
IMPORTANT: Observe all government codes and ordinances.
WARNING: For your safety, the information in this manual must be followed to minimize the risk
of fire or explosion, or to prevent property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not attempt to switch on any appliances.
• Do not touch any electrical switches.
• Do not use any phones in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• lf you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
NOTE: This cooktop is manufactured for use with Natural gas. To convert to LP/Propane gas, see
instructions in the Gas Conversion Kit provided in the literature package.
Proper gas supply connection must be available. See "Gas supply requirements”.
In the State of Massachussets, the following installation instructions apply:
- Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter
qualified or licensed by the State of Massachusstets.
- If using a Ball valve, it shall be T-handle type.
- A flexible gas connector, when used, must not exceed 3 feet.
4
Instructions for the Installer
2. COOKTOP MEASUREMENTS
5
Instructions for the Installer
3. POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS
NOTE: The following operation requires building and/or carpentry work and must therefore be carried
out by a competent technician.
Installation can be carried out on various material, such as masonry, metal, solid wood, plastic laminated
wood etc. As long as they are heat resistant (T = 90°C - 194° F).
Observe all governing codes and ordinances. Do not obstruct flow or combustion and ventilation air.
- It is the installer’s responsibility to comply with installations guidelines specified on the model/serial
rating plate. The model/serial rating plate is located on the underside of the cooktop burner box.
- The cooktop should be installed in a location away from strong draft areas, such as windows, doors
and strong heating vents or fans.
- All openings in the wall or floor where cooktops is to be installed must be sealed.
- Cabinet opening dimensions that are shown must be used. Given dimensions are minimum
clearances.
- Grounded electrical supply is required. See “Electrical Requirements” section. Proper gas supply
connection must be available. See “Gas Supply Requirements” section
To prevent accidents or ruining the mobile components of the appliance, the following steps must be
taken before performing the procedures described below:
1 Remove all packaging parts (e.g. crate, carton, polystyrene and metal hooks). Do not eliminate this
manual as it is an integral part of the appliance and it should be kept handy for easy reference
whenever needed.
2 Temporarily remove all removable parts from the cooktop that could fall and cause personal injury or
damage to objects (burners, crowns and flame caps) during the attachment procedures These parts
must be refitted before using the appliance.
The measurements supplied in the tables referring to the figure below must be followed when attaching
the appliance to the support structure.
6
Instructions for the Installer
Cooktop
widht
23 5/8”
600 mm
27 1/2”
700 mm
39 3/8”
1000 mm
MINIMUM DISTANCE
A B C D E F G
22” - 22 7/16”
560 - 570 mm
22” - 22 7/16”
560 - 570 mm
33 11/16” - 33 7/8”
855 - 860 mm
Gas line opening
Wall: everywhere, 5” (12.7 cm) below underside of countertop.
Cabinet base: everywhere, within 6” (15.2 cm) from rear wall is recommended.
Grounded outlet
Locate within 24” (61 cm) from the right rear corner of the cut out drawer.
18 7/8”- 19”
478 - 482 mm
18 7/8”- 19”
478 - 482 mm
19 1/10” - 19 3/10”
485 - 490 mm
8 1/4”
210 mm
8 1/4”
210 mm
8 1/4”
210 mm
3 3/8”
86 mm
3 3/8”
86 mm
4 7/16”
112 mm
1 7/16”
36 mm
1 7/16”
36 mm
1 7/16”
36 mm
13/16” - 1 9/16”
20 - 40 mm
13
/16” - 1 9/16”
20 - 40 mm
13/16” - 1 9/16”
20 - 40 mm
23 5/8”
600 mm
27 1/2”
700 mm
39 3/8”
1000 mm
7
Loading...