Smeg PTS727NU5, PTS727U5, PTS727BU5 Instruction manual

Table of Contents

1. IMPORTANT SAFETY INSTRUCTIONS ................................................................................. 4

2. COOKTOP MEASUREMENTS ............................................................................................... 5

3. POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS .................................... 6

3.1 Gas supply requirements ................................................................................................................................ 8

3.2 Electrical requirements .................................................................................................................................... 9

4. INSTALLING THE COOKTOP ............................................................................................... 11

5. CHECKING OPERATION ...................................................................................................... 13

6. WIRING DIAGRAMS .............................................................................................................14

WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, or to prevent property damage, personal injury or death.

Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not attempt to switch on any appliances.

• Do not touch any electrical switches.

• Do not use any phones in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

• lf you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is able to install, commission and test the appliance

Important Safety Instruction

1. IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS – Your safety and the safety of others are very important. We have provided many important safety messages throughout this manual and on the appliance. Read all instructions before using the appliance and always obey all safety messages.

RECOGNIZE SAFETY INFORMATION

This is a safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

UNDERSTAND SIGNAL WORDS

A signal word – DANGER, WARNING, or CAUTION – is used with the safety alert symbol. DANGER identifies the most serious hazards. It means you can be killed or seriously injured if you do not immediately follow the instructions. CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

follow the instructions. WARNING means you can be killed or seriously injured if you do not

All safety messages will inform you of potential hazards, on how to reduce the risk of injury and what can occur if the instructions are not followed.

IMPORTANT: Observe all governing codes and ordinances.

WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, or to prevent property damage, personal injury or death.

Do not store or use gasoline or other flammable vapors, liquids or materials near this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not attempt to switch on any appliances.

• Do not touch any electrical switches.

• Do not use any phones in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

• lf you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

NOTE: This cooktop is manufactured for use with Natural gas. To convert to LP/Propane gas, see instructions in the Gas Conversion Kit provided in the literature package.

A proper gas supply connection must be available. See "3.1 Gas supply requirements”.

In the State of Massachussetts, the following installation instructions apply:

- Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachussetts.

- If using a ball valve, it shall be the T-handle type.

- A flexible gas connector, when used, must not exceed 3 feet.

Instructions for the Installer

2. COOKTOP MEASUREMENTS

PTS605

PTS727

Instructions for the Installer

3. POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS

NOTE: The following operation requires building and/or carpentry work and must therefore be carried out by a competent technician. Installation can be done on various materials, such as masonry, metal, solid wood, plastic laminated wood etc. as long as the material is heat resistant (T = 90°C - 194° F). Observe all governing codes and ordinances. Do not obstruct flow or combustion and ventilation air.

- It is the responsibility of the installer to comply with installation guidelines specified on the model/ serial ID plate. The model/serial ID plate is located on the bottom of the cooktop burner box.

- The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.

- All openings in the wall or floor where the cooktop is to be installed must be sealed.

- Appliance should not be installed with an air curtain ventilation system that blows air downward toward the appliance, unless the ventilation system and appliance have been designed, tested in accordance with ANSI Z21.1 and listed by an independent testing laboratory for combination use. This type of ventilation system may cause ignition and combustion problems with the gas cooking appliance resulting in personal injury or unintended operation.

- The cabinet opening dimensions that are shown must be used. The given dimensions are minimum clearances.

- A grounded electrical supply is required. See the “3.2 Electrical requirements” section. A proper gas supply connection must be available. See the “3.1 Gas supply requirements” section.

To prevent accidents or ruining the mobile components of the appliance, the following steps must be taken before performing the procedures described below:

1 Remove all packaging parts (e.g. crate, carton, polystyrene and metal hooks). Do not throw away this

manual as it is an integral part of the appliance and should be kept handy for easy reference whenever needed.

2 Temporarily remove all removable parts from the cooktop that could fall and cause personal injury or

damage to objects (burners, crowns and flame caps) during the hook-up. These parts must be refitted before using the appliance.

The measurements supplied in the tables referring to the figure below must be followed when attaching the appliance to the support structure.

+ 9 hidden pages