INSTRUCTION MANUAL
GGUUIIDDEEFFOORRUUSSIINNGGTTHHEEDDIISSHHWWAASSHHEERRAANNDDTTHHEEWWAASSHHIINNGGPPRROOGGRRAAMMS
S
Contents
1. Description of the controls________________________________14
2. Troubleshooting _______________________________________21
Thank you for choosing one of our products.
You are advised to read this manual carefully; it contains all the
information you need about the right conditions for the proper, safe use
of your dishwasher.
The individual sections are laid out to provide you with a step-by-step
guide to all your appliance's functions; the texts are easy to understand
and are complete with detailed illustrations.
This user-friendly manual will provide answers to all your questions
about use of the dishwasher.
For any other information about use and maintenance of the dishwasher,
read the enclosed manual carefully.
USER INSTRUCTIONS: useful information is provided for the use of the
washing programs and all the dishwasher's functions.
User instructions
1. Description of the controls
1.1 Front panel
All the dishwasher control are grouped on the front panel.
1 ON/OFF
2 SELECTION PROGRAMS
3 POWER ON
4 PROGRAMS
5 NO SALT
6 NO RINSE AID
7 PHASES/PROGRAM
8
RECESSED DOOR HANDLE
BUTTON
LIGHT
LIGHTS
LIGHT (depending on the models)
LIGHT (depending on the models)
LIGHTS
BUTTONS
(P1...P5)
User instructions
PROGRAM SELECTION TYPE AND GRADE DIRT
PANS AND DISHES
SOAK
IN WAITING OF
COMPLETING
THE LOAD
PROGRESS
PROGRAM
Cold prewash 15' 6 0,03
DURATION CONSUMPTION
MINUTES
WATER
(2)
LITRES (1)
POWER
KWh (2)
Wash at 45°C
LIGHT
DISHES
NOT VERY DIRTY
Cold rinse
Rinse at 68°C
70' 12 1,00
Dry
Cold prewash
BIO
PANS AND DISHES
(*)
NOT VERY DIRTY BUT
WITH DRY RESIDUALS
Wash at 50°C
Cold rinse
Rinse at 65°C
170' 17 1,05
Dry
Cold prewash
NORMAL
PANS AND DISHES
DIRTY AND WITH
DRY RESIDUALS
Wash at 65°C
Cold rinse
Rinse at 68°C
90' 17 1,30
Dry
Prewash at 45°C
Wash at 70°C
2 cold rinses
Rinse at 70°C
110' 20 1,60
SUPER
PANS AND DISHES
VERY DIRTY AND
WITH DRY RESIDUALS
Dry
Only run the soak program with half loads.
(*) Reference program as per EN 50242 standard.
(1) Average power consumption with the softener set on level 2.
(2) The cycle duration and power consumption may vary according to the water and room
temperatures, and the type and amount of dishes.
The washing cycle will not take place if the dishwasher door is left open
or not properly closed.
User instructions
1.2 Washing programs
The dishwasher is equipped with a control panel, described in chapter
"1. Description of the controls", from which it is possible to carry out all
the power switch-on, switch-off and programming operations.
Before starting a washing program make sure that:
• The water supply tap is
• The
• The baskets have been
• The spray arms are able to
• The dishwasher door is
LIGHTING
When the
and the light
PHASES/PROGRAM
correct amount of detergent
dispenser
obstruction.
.
ON/OFF
(3)
button
open.
has been added to the
correctly loaded.
rotate freely
securely closed
(1)
is pressed, the dishwasher switches on
comes on. About
(7)
lights
will come on.
and without
.
2 seconds
later, the
PROGRAMMING
In this model of dishwasher, all programming procedures can only be
carried out with the
PROGRAMS
off.
SELECTION PROGRAM
When the button relating to the program required is pressed, the relative
light will come on to confirm the operation.
lights
door closed
(4)
and
. As long as the door is open, the
PHASES/PROGRAM
The program selection is possible
through the relative buttons
lights
(7)
will remain
(2)
.
User instructions
y
START PROGRAM
To start the dishwasher, press the button of the
for a few seconds, until the light of the first phase of the selected
program starts to flash (confirmation beep).
PROGRAM (2)
required
As the program runs, the
PHASES/PROGRAM
lights
(7)
will indicate the
current cycle status.
Prewash
Wash
Rinse
Dr
The light of the phase in progress will
flash, while the lights of the previous and
subsequent phases remain on.
N.B.
during execution of programs which
do not include a prewash, the first
PHASES/PROGRAM
light
(7)
will remain
off.
END PROGRAM
When the program finishes, a buzzer sounds
briefly and all the
(7)
flash.
Press any of the
PHASES/PROGRAM
lights
SELECTION PROGRAMS
buttons
(2)
, stops the light
flashins, and the dishwasher is now ready to perform a new cycle;
opening and shutting the door or switching the appliance off and on has
the same effect.
User instructions
INTERRUPTION OF A PROGRAM
In order to interrupt a running program it is necessary:
• press one of the
SELECTION PROGRAMS
the current phase will go out;
• keep the button pressed until the
PHASES/PROGRAM
come on (confirmation buzzer);
• start the program (see “
S
TART PROGRAM
”).
TO CHANGE A PROGRAM
To change the running program it is necessary:
• to interrupt the running program (see “
I
NTERRUPTION OF A PROGRAM
• select the new program;
• start the program (see “
S
TART PROGRAM
”).
ANNULLING A PROGRAM
To annul the program in progress, it must first be interrupted (see
I
“
NTERRUPTION OF A PROGRAM
”).
buttons
(2)
, the light of
lights
(7)
”);
Now press buttons P1+P2 simultaneously and
the first three program lights will come on.
In case that the door is opened during the operation, to the next door
closing it is going to be necessary to start the program as shown in
paragraph “
TART PROGRAM
S
”. The program will resume from the point in
which it was interrupted.
In case that the tub temperature is higher than 50°C the program
will start about 30 seconds later.
User instructions
TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT
• Always try to run the dishwasher
• Do not wash the dishes in running water.
• Use the washing program that is
load.
• Do not carry out any preliminary rinsing.
• If available, connect the dishwasher to a hot water supply up to
60°C.
TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT
THE ENVIRONMENT
The phosphates contained in dishwasher detergents are harmful to the
environment. To avoid using excessive amounts of detergent and to
save on electricity, observe the following:
•
separate
resistant to aggressive detergents and high temperatures;
•
do not pour
the more delicate items from dishes that are more
the detergent directly on the dishes.
fully loaded
most appropriate
.
for each type of
REMOVING THE DISHES
At the end of the washing program, wait at least
removing the dishes, to allow them to cool down. To prevent any water
droplets on the upper basket from falling on the dishes in the lower
basket, it is
upper basket.
advisable
to unload the lower basket first, and then the
20 minutes
before
User instructions
ADJUSTING THE WATER SOFTENING SYSTEM
The dishwasher is equipped with an device for the user to adjust the
water softening system according to the hardness of the water supply.
According to the machine model, the selector which acts on the
adjustment may be located:
• inside the plastic locking ring located on the
the dishwasher;
• inside the water softener, just below the cap.
Both allow for adjustment to 5 settings:
right-hand
side, inside
WATER HARDNESS TABLE
WATER HARDNESS
German Degrees (°dH) French Degrees (°dF)
0 - 4 0 - 7 Setting N. 1 NO SALT
5 - 15 8 - 25 Setting N. 1
16 - 23 26 - 40 Setting N. 2
24 - 31 41 - 60 Setting N. 3
32 - 47 61 - 80 Setting N. 4
48 - 58 81 - 100 Setting N. 5
SETTING
Contact your local water board for information on the hardness of your
water supply.
User instructions
2. Troubleshooting
In case of a malfunction, the dishwasher will identify the program by
switching on a combination of lights.
When an alrm is present, all the
PROGRAM
PHASES/PROGRAM
the error code:
CODE PHASES LIGHTS DESCRIPTION
lights
(4)
come on, while the
(7)
lights
identify
E1
E2
E3
E4
E5
E6
E7
E8
The anti-flooding system (if installed) has been
tripped.
The system which limits the water level inside the
dishwasher (safety unit) has been tripped.
The appliance cannot heat the water.
Temperature sensor disconnected.
The appliance is not able to take in water.
The appliance is not able to pump out the water
from the tank.
The appliance is not able to measure the amount
of water loaded accurately (on models with turbine
flow-regulator only).
Anomaly in the system which distributes water to
the basket (where installed).
E9
The maximum level of water for loading has been
exceeded (on models with turbine flow-regulator
only).
INSTRUCTION MANUAL
WWAARRNNIINNGGSSAANNDDRREECCOOMMMMEENNDDAATTIIOONNSS,,GGUUIIDDEEFFOORRTTHHEEUUSSEEOOFFBBAASSKKEETTS
AANNDDFFOORRCCLLEEAANNIINNGGDDIISSHHWWAASSHHEERRS
S
S
Contents
1. Safety and operating instructions __________________________ 28
2. Installation and hook-up _________________________________31
3. Operating instructions___________________________________33
4. Cleaning and maintenance _______________________________46
Thank you for choosing one of our products.
You are advised to read this manual carefully; it contains all the
information you need about the right conditions for the proper, safe use
of your dishwasher.
The individual sections are laid out to provide you with a step-by-step
guide to all your appliance's functions; the texts are easy to understand
and are complete with detailed illustrations.
Following the cleaning instructions provided here will keep your
dishwasher's performance at peak levels in the long term.
This user-friendly manual will provide answers to all your questions
about use of the dishwasher.
INSTALLATION INSTRUCTIONS: these are intended for the qualified
technician who must carry out the installation, hook-up and testing of
the appliance.
USER INSTRUCTIONS: useful advice is provided for the use of baskets,
spray arms, containers and filters.
Safety instructions
1. Safety and operating instructions
THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST
ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE
USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS
CONTAINED IN THIS MANUAL.
INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN
COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS
INTENDED FOR DOMESTIC USE, AND COMPLIES WITH THE
DIRECTIVES 72/23, 89/336 (INCLUDING 92/31)
INCLUDING THE PREVENTION AND ELIMINATION OF RADIO FREQUENCY
INTERFERENCE.
THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE:
AND DRYING OF DISHES
IMPROPER.
USES OTHER THAN THOSE DESCRIBED ABOVE.
THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL NUMBER
AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE
DOOR.
NEVER BE REMOVED.
DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED
WITHIN THE HOME. SEPARATE THE VARIOUS MATERIALS WHICH MAKE
UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE
COLLECTION CENTRE.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR
THE NAME PLATE ON THE INNER EDGE OF THE DOOR MUST
; ANY OTHER USE SHALL BE CONSIDERED
CURRENTLY IN FORCE,
EEC
WASHING
THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN
ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO
PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO EARTH THE
APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.
THE POWER SUPPLY LEAD PLUG AND THE RELATIVE SOCKET MUST BE
OF THE SAME TYPE AND COMPLY WITH THE RELEVANT REGULATIONS.
CHECK THAT THE MAINS VOLTAGE AND FREQUENCY ARE THE SAME AS
THE VALUES MARKED ON THE NAMEPLATE. DO NOT USE ADAPTERS OR
SHUNTS.
SUPPLY LEAD.
NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER
• AFTER INSTALLATION, THE PLUG MUST REMAIN ACCESSIBLE.
• IN THE EVENT OF DAMAGE TO THE POWER CORD, HAVE IT
REPLACED BY A QUALIFIED TECHNICIAN.
Safety instructions
IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR,
ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT
OBSTRUCTED.
ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO AVOID
WASTING ELECTRICITY.
OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE
MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET,
AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR
CHILDREN (LOCKS, DOORS, ETC.). THE APPLIANCE MUST THEN BE TAKEN
TO A SORTED WASTE COLLECTION CENTRE.
IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER FROM THE
ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP. THEN
CALL IN A QUALIFIED TECHNICIAN.
DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING
TRANSIT! IF IN DOUBT, CONSULT YOUR DEALER.
THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE
WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY A
QUALIFIED TECHNICIAN.
THE APPLIANCE IS INTENDED FOR USE BY ADULTS.
CHILDREN TO COME NEAR OR PLAY WITH THE DISHWASHER. KEEP
CHILDREN AWAY FROM DETERGENTS AND FROM THE OPEN
DISHWASHER DOOR. THE PACKAGING MATERIALS (PLASTIC BAGS,
POLYSTYRENE, METAL BARS, ETC.) MUST NOT BE LEFT WITHIN THE
REACH OF CHILDREN.
KEEP CHILDREN AWAY FROM THE OPEN DISHWASHER. THE APPLIANCE
MAY CONTAIN RESIDUES OF DETERGENT WHICH CAN CAUSE
IRREVERSIBLE DAMAGE TO THE EYES, MOUTH, AND THROAT, AS WELL
AS POSSIBLE DEATH BY SUFFOCATION.
DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE
WHICH MAY CAUSE AN EXPLOSION.
DO NOT LOAD DISHES THAT ARE SOILED WITH ASH, WAX OR PAINTS.
LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY
CAUSE THE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK.
DO NOT ALLOW
Safety instructions
DO NOT UNDER ANY CIRCUMSTANCES TOUCH THE HEATING ELEMENT
IMMEDIATELY AFTER THE END OF A WASHING PROGRAM.
OVER TIME, THE DISHWASHER HEATING ELEMENTS MAY CHANGE
COLOUR, IN PART OR OVERALL. THIS IS PERFECTLY NORMAL AND DOES
NOT IN ANY WAY AFFECT THE OPERATION OF THE APPLIANCE.
DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE
THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM
AND BEFORE THE DRYING CYCLE.
KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED
IN THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN THE
TOP BASKET. TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT
THEY DO NOT PROJECT FROM THE BASKET.
AQUASTOP MODELS
THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A
WATER LEAK. WHEN THE AQUASTOP DEVICE IS TRIPPED, CALL IN A
QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT.
IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A
SOLENOID VALVE INSIDE THE WATER INTAKE HOSE.
HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO
WATER.
DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY
AND FROM THE WATER SUPPLY.
IN THE EVENT OF DAMAGE TO THE WATER INTAKE HOSE,
DO NOT CUT THE
IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK
TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW. IF
THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT
FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST
TECHNICAL SERVICE CENTRE.
APPLIANCE.
THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE
REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL
EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED
EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN:
CARRIED OUT BY UNAUTHORISED PERSONS WILL INVALIDATE THE
WARRANTY, AS WELL AS POSING A POTENTIAL HAZARD TO THE USER.
The manufacturer declines all responsibility
DO NOT ATTEMPT TO REPAIR THE
REPAIRS
for damage to persons or property
resulting from failure to observe the above precautions, from tampering with
even a single component of the appliance, or from the use of non original
spare parts.
Installation instructions
2. Installation and hook-up
Remove the polystyrene basket retainers. Position the appliance in the
desired place of installation. The back or sides of the dishwasher may be
placed up against walls or other furniture units. If the dishwasher is
installed near a heat source, fit the special insulating panel to prevent
overheating and malfunction of the appliance. To ensure stability, install
integrated or built-under dishwashers only under continuous worktops,
and screw them to the adjacent units. To facilitate the installation
procedure, the intake and drain hoses can be positioned in any direction;
make sure that the hoses are not kinked, crushed or pulled too tightly.
Make sure to tighten the locking ring-nut once the pipes have been
placed in the direction required. A hole at least 8 cm in diameter is
required to allow the power supply cable and pipes to pass.
Level the appliance on the floor using its adjustable feet. This operation
is essential for ensuring correct operation of the dishwasher.
Installing a hob on top of a free-standing dishwasher is absolutely
forbidden. Building-in a dishwasher underneath a ceramic hob is
absolutely forbidden.
A dishwasher can be built-in underneath a conventional hob provided
there is no break in the kitchen worktop, and the dishwasher and hob
are installed and secured correctly, so that no hazards are
generated.
For free-standing models only: if the appliance is not built-in and is
therefore accessible on one side, the door hinge area must be covered
for safety reasons (injury hazard).
The covering fixtures are available as an accessory from specialist
dealers or the After-Sales Service.
Some models are equipped with only one adjustable foot at the rear,
which can be adjusted by turning the screw on the lower front part of the
appliance.
2.1 Water supply connection
Preventing the risk of clogging or damage: if the water pipe is new or
has not been used for a long time, before connecting to the water supply
check that the water is clear and free of impurities, to prevent damage to
the appliance.
The dishwasher must always be connected to the water system
with new hoses; old or used hoses must never be reused.
Installation instructions
CONNECTING TO THE WATER SUPPLY
Connect the intake hose to a cold water supply with ¾”
gas thread, inserting the filter A supplied with the
dishwasher.
place with your hands and then complete by
tightening about ¼ of a turn with pliers.
In dishwashers equipped with the ACQUASTOP
device, the filters is already fitted inside the threaded
ring.
Take care to screw the hose firmly into
The dishwasher can also be connected to a hot water supply
exceeding 60°C
washing time by approximately 20 minutes, but slightly reduces its
effectiveness. Make the connection to the domestic hot water supply using
the same procedure described for connecting to the cold water supply.
DRAIN CONNECTION
Insert the dishwasher’s drain hose
into a drain pipe having a diameter
of at least
place it inside the kitchen sink
using the plastic support provided,
taking care not to crush or
excessively bend the hose. It is
important to prevent the hose from
coming loose and falling. For this
purpose, the plastic support is
equipped with a hole for tying it to
the wall or water tap.
The free end should be positioned at a height of between
cm
, and should never be submerged in water. If a horizontal drain
extension hose is used (for a maximum of 3 m) the drain hose can be
placed at a maximum height of
. Supplying the appliance with hot water cuts down the
4 cm
, or alternatively,
30 and 100
85 cm
from the ground.
not
2.2 Electrical connection
Plug the power cord into a suitable electrical outlet, according to the
instructions given in chapter "1. Safety and operating instructions".
User instructions
3. Operating instructions
Once the dishwasher has been correctly installed, prepare for use as
follows:
•
Adjust the water softening system;
•
Add the regenerating salt;
•
Add the rinse aid and detergent.
3.1 Using the water softening system
The amount of scale contained in the
water (water hardness index) can cause
whitish staining on the dry dishes, which
tend to become dull over time. The
dishwasher is equipped with an automatic
softening system which uses a special
regenerating salt to reduce the hardness
of the water.
The dishwasher is factory set for water
hardness level 3(average hardness
41-60°dF –24-31°dH
When using water of medium hardness, the regenerating salt container
should be refilled after approximately
container can hold approximately
are equipped with an optical no-salt indicator. In these models, the cap
of the salt container contains a green float which descends as the salt
concentration in the water drops. When the green float can no longer be
seen through the transparent cap, the container must be topped up with
regenerating salt. The container is situated at the bottom of the
dishwasher. After removing the lower basket, unscrew the salt container
cap by turning it anticlockwise and pour in the salt using the funnel
supplied with the dishwasher. Before replacing the cap, remove any salt
residues from around the opening.
).
20 washing cycles
1.7 Kg
of salt in grains. Some models
SALT
. The salt
• When using the dishwasher for the first time, in addition to the salt it
is also necessary to add one litre of water to the container.
• Each time the salt container is refilled, make sure that the cap is
securely closed. The mixture of water and detergent must never
penetrate the salt container, as this would compromise the operation
of the regeneration system. In the event of this occurring, the
warranty will be invalidated.
•
Only use regenerating salt specially formulated for domestic
dishwashers. If using salt tablets, do not fill the container
completely.
User instructions
•
Do not use table salt as it contains insoluble substances which,
over time, may damage the water softening system.
• When necessary, refill the regenerating salt container before
starting the washing program. In this way, the excess saline
solution will be immediately removed by the water; the prolonged
presence of salt water inside the tank may lead to corrosion.
Be careful not to confuse the salt and detergent packages; adding
detergent to the salt container will damage the water softening system.
3.2 Using the rinse aid and detergent dispensers
The detergent and rinse aid
dispensers are situated on the inner
part of the door: the
dispenser
rinse aid dispenser
With the exception of the SOAK program, before every washing cycle it
is necessary to add the required amount of detergent to the detergent
dispenser. The rinse aid, on the other hand, should only be added as
required.
is on the left, and the
detergent
is on the right.
User instructions
ADDING THE RINSE AID
The rinse aid helps the dishes dry faster and
prevents the formation of scale deposits and
staining; it is automatically added to the water
during the final rinse cycle, from the container
situated on the inner side of the door.
•
Open the door.
•
Rotate the container cap anticlockwise by ¼ of a turn and remove it.
•
Add the rinse aid until the container is full (approximately 140 cc).
The optical level indicator on the side of the cap should be
completely obscured. Refill the rinse aid when the optical level
indicator becomes clear again, or when the rinse aid warning light
illuminates.
•
Replace the cover and turn it in a clockwise direction.
•
Use a cloth to remove any spillage of rinse aid which might lead to
the formation of excess foam.
ADJUSTING THE RINSE AID DISPENSER SETTING
The dishwasher is factory set for medium water hardness. However it
possible to change the setting by turning the dispenser’s selector to the
desired position: the amount of rinse aid dispensed is proportional to the
selector position.
The setting must be increased when the washed dishes appear dull or
have circular staining.
•
To adjust the rinse aid setting, rotate the dispenser cap through a
quarter turn in an anticlockwise direction and remove it.
•
Then use a screwdriver to rotate the rinse aid selector to the desired
position.
•
Replace the cap, turning it clockwise.
• The amount of rinse aid must be increased if the washed dishes
appear dull or feature circular stains.
• If, on the other hand, the dishes are sticky or have white streaks, it
is necessary to reduce the rinse aid setting.
User instructions
ADDING THE DETERGENT
To open the detergent dispenser cap, lightly press
the button P. Add the detergent and close the cap
carefully.
During the washing cycle, the dispenser will be
opened automatically.
• When a INTENSIVE program is selected, in addition to the normal
dose of detergent, it is necessary to add an additional amount inside
compartment G or H.
• Use only detergents specially formulated for dishwashers. For
optimal washing results it is important to use a good quality
detergent.
• The detergent packs must be sealed and stored in a dry place to
prevent the formation of lumps which may negatively affect washing
results. Once opened the detergent packs should not be kept for too
long, otherwise the detergent loses its effectiveness.
• Do not use detergents formulated for washing dishes by hand,
because they produce a great deal of foam and may negatively
affect the operation of the dishwasher.
• Add the correct amount of detergent. An insufficient amount of
detergent will result in a partial removal of dirt from the dishes,
whereas an excessive amount is wasteful and does not improve the
washing results.
User instructions
• The market offers liquid and powder detergents with differing
chemical compositions, which may contain phosphates, or be
phosphate-free but contain natural enzymes.
- Detergents containing phosphates are more effective against
grease and starch at temperatures above 60°C.
- Enzyme detergents, on the other hand, are also effective at lower
temperatures (from 40 to 55°C) and are more easily
biodegradable. With enzyme detergents it is possible to obtain at
low temperatures comparable results to those which can only be
achieved at 65°C using traditional detergents.
For the safeguarding of the environment we recommend the use of
phosphate- and chlorine free detergents.
•
"3/1" Products
If you wish to use detergents which already contain salt and rinse
aid, check whether your dishwasher is fitted with the "3/1 option
button" on the "Controls description" page and then refer to the
section which explains how to use this function.
If the button is not provided, we recommend the use of conventional
products (separate detergent, salt and rinse aid), because with
conventional washing cycles "3/1" products might create
problems such as a white deposit, poor drying results and residues
left on dishes.
The introduction of detergent into the rinse aid dispenser, even in
liquid form, will damage the dishwasher.
User instructions
3.3 General warnings and recommendations
Before using the dishwasher for the first time, it is advisable to read the
following recommendations concerning dish types to be washed and
their loading.
There are generally no constraints on the washing of domestic dishes,
but in certain cases it is necessary to take their characteristics into
account.
Before loading the dishes into the baskets it is necessary to:
• remove coarse food remains: e.g. bones, fish-bones, etc. which
may clog the filter or damage the wash pump.
• soak any pots or pans with burnt-on food remains on the bottom to
facilitate removal, then load them into the LOWER BASKET.
If a small quantity of dishes has to be washed, use the “½ load wash”
option (certain models only); this saves electricity and water.
Remember to load the upper basket only; the lower basket must
be left empty.
There is no need to pre-wash the dishes under running water before
loading them into the baskets since this only wastes water.
Correct loading of the dishes helps ensure optimal washing
results.
WARNING!
• Make sure that the dishes are securely in place so that they cannot
tip over or obstruct the rotation of the spray arms during the
washing cycle.
• Do not place very small objects in the baskets as these could fall
and obstruct the spray arms or the wash pump.
• Containers such as cups, bowls, glasses and pots should always
be loaded with the opening facing downwards and with any cavities
at an angle, to allow the water to drain out.
• Do not stack dishes or place them in such a way that they cover
one other.
• Do not place glasses too close together because they may knock
against each other and break, or there might be staining at the
point where they touch.
MAKE SURE that the items being washed are dishwasher-safe.
User instructions
Items which are not dishwasher-safe:
•
Wooden dishes, pots or pans: these may be damaged by the
high washing temperatures.
•
Handcrafted items: these are rarely suitable for washing in a
dishwasher. The relatively high water temperatures and the
detergents used may damage them.
•
Plastic dishes: heat resistant plastic dishes must be washed in the
upper basket.
•
Dishes and objects in copper, tin, zinc or brass: these tend to
stain.
•
Aluminium dishes: items made from anodised aluminium may
lose their colour.
•
Silverware: silver items may stain.
•
Glass and crystal: in general, glass and crystal objects can be
washed in the dishwasher. However, certain types of glass and
crystal may become dull and lose their clearness after many
washings. Therefore, for these items we recommend using the
least aggressive program available.
•
Decorated items: the decorated objects available on the market
are generally able to withstand washing in the dishwasher,
although the colours may fade after a great many washes. If in
doubt as to the fastness of the colours, it is advisable to wash just a
few items at a time for approximately one month.
User instructions
3.4 Using the baskets
The dishwasher has a capacity of
dishes.
EN 50242 STANDARD LOADS FOR CERTIFICATION BODIES
LOWER BASKET UPPER BASKET
12 place-settings
, including serving
for AAA models only (see energy label)
UPPER BASKET
The upper basket must be set in the low position.
User instructions
LOWER BASKET
The lower basket receives the full force of the lower spray arm, and
should therefore be used for the “toughest” items with a heavier degree
of soiling.
All types and combinations of loads are
permitted, provided that the dishes, pots and
pans are arranged with all the soiled surfaces
exposed to the water jets coming from the
bottom.
With fixed supports
To make the most of the space inside the
basket when loading large items, certain
models are equipped with tip-up supports for
plates in 2 or 4 sections.
With tip-up supports
LOADING THE LOWER BASKET
Carefully load flat plates, soup plates, dessert and serving dishes,
positioning them vertically. Pots, pans and their covers must be loaded
upside down. When loading soup plates and dessert bowls, be sure to
leave a gap between them.
Loading examples:
½ LOAD
(certain models only)
User instructions
CUTLERY BASKET
The cutlery should be arranged in an orderly manner inside the basket,
with the handles pointing downwards. Take care during loading to avoid
injury from the knife blades. The basket is suitable for all types of cutlery,
except those long enough to interfere with the upper spray arm. Ladles,
wooden spoons and cooking knives can be placed in the upper basket,
making sure that the knife blades do not protrude from the basket.
The dishwasher is complete with two cutlery baskets, which means that
one of them can be removed, freeing space in the bottom basket, if there
is not much cutlery to be washed, or if a ½ load program is being used
(on models with this function).
The basket features an
up supports
, offering a choice of possible combinations to allow
optimum use of the space available.
exclusive system of independent sliding tip-
Vertical
inserts
Movement required
to extract the inserts
Horizontal
insert
closed
Horizontal
insert
open
User instructions
UPPER BASKET
It is recommended to load the upper basket with small- or medium-sized
items such as glasses, small plates, tea or coffee cups, shallow bowls
and light objects made from heat resistant plastic. If the upper basket is
used in the lowermost position, it can also be loaded with serving dishes,
provided they are only slightly soiled.
To make full use of the space available, the
top basket has two plastic grids that can be
lifted to make room for tall glasses such as
stem glasses.
The top basket is fitted (on the left)
with two plastic racks which can be
raised to make room for tall glasses,
such as stem glasses.
On the right there are two cutlery
racks designed to take knives and
teaspoons; when not in use, they can
be left vertical, attached to the
basket.
To use the space designed for
teaspoons, remove the insert as
shown in the illustrations.
for AAA models only
(see energy label)
User instructions
LOADING THE UPPER BASKET
Load plates facing forward; cups, bowls etc. must always be facing
downwards. The left-hand side of the basket can be loaded with two
layers of cups and glasses. The centre can be filled with plates and sideplates, fitted upright into the supports provided.
Loading examples:
½ LOAD
(certain models only)
½ LOAD
for AAA models only
(see energy label)
User instructions
ADJUSTING THE UPPER BASKET
The upper basket can be adjusted in
user’s needs and according to the height of the dishes in the lower
basket. Proceed as follows.
two positions
, according to the
Pull-out
•
pull out the right-hand basket guide
•
remove the stop, first releasing it as shown in the diagram
•
push the guide to free the wheels
•
fit the upper or lower pair of wheels into the guide, depending on the
•
return the stop to its original position
Push-button
•
pull out the basket to its limit position and pull the right side
•
To return to the original position, pull out the upper basket again and
version:
;
;
;
setting required
;
.
version:
upwards. At this point it is possible to load larger sized plates into
the lower basket.
press the release lever.
User instructions
4. Cleaning and maintenance
Before carrying out any work, always disconnect the appliance
from the electrical power supply.
4.1 General warnings and recommendations
Avoid the use of acidic or abrasive detergents.
Clean the outer surfaces and door-lining of the dishwasher regularly
using a soft cloth moistened with water or with a normal detergent
suitable for painted surfaces. Clean the door gaskets with a damp
sponge. Periodically (once or twice a year) it is advisable to clean the
tank and gaskets, using a soft cloth and water to remove any deposits.
CLEANING THE WATER INTAKE FILTER
The water intake filter Alocated at the outlet of the water supply tap
needs to be cleaned periodically.
After having closed the water supply tap, unscrew the end of the water
intake hose, remove the filter Aand clean it delicately under running
water. Reassemble filter Ain its seat and carefully screw the water
intake hose back into position.
CLEANING THE SPRAY ARMS
The spray arms can be easily removed for periodic cleaning of the
nozzles, to prevent possible clogging. Wash them under running water
and carefully replace them in their seats,
movement is in no way impeded
•
To remove the
•
To remove the
central part.
•
To remove the
arm and pull the orbital unit upward. Wash the arms under a jet of
running water and return them carefully to their seat.
reassembly, check that the spray arms turn freely.
check that they have been installed correctly.
upper
spray arm, unscrew locking ring R.
lower
orbital
spray arm assembly, take hold of the longer
.
spray arm, simply lift it up, pulling by the
checking that their rotary
After
Otherwise,
14$+6#.
User instructions
CLEANING THE FILTER UNIT
•
It is advisable to periodically inspect the centre filter Cand, if
necessary, to clean it. To remove the filter, grip the tabs, turn them
anticlockwise and lift upwards;
•
push the centre filter Dfrom the underside to remove it from the
micro-filter:
•
separate the two parts which make up the plastic filter by pressing
the body of the filter in the zone shown by the arrows;
•
remove the centre filter by lifting it upwards.
GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT
MAINTENANCE:
• The filters should be cleaned under running water using a stiff
brush.
• It is essential to thoroughly clean the filters according to the
above instructions: the dishwasher cannot function if the filters are
clogged.
•
Carefully replace the filters in their seats, to avoid damaging the
wash pump.
PROLONGED DISUSE:
• Run the soak program twice in succession.
•
Unplug the power cord from the socket.
•
Leave the door slightly open, in order to prevent the formation of
unpleasant odours inside the washing tank.
•
Fill the rinse aid dispenser.
•
Shut off the water supply tap.
User instructions
BEFORE STARTING THE DISHWASHER AFTER PROLONGED
DISUSE:
• Check that there are no deposits of sludge or rust inside the water
pipe: if there are, allow the water to run from the water supply tap for
a few minutes.
•
Plug the power cord back into the socket.
•
Reconnect the water intake hose and open the tap again.
TROUBLESHOOTING MINOR PROBLEMS
In some cases it is possible to remedy minor problems by referring to the
following instructions:
If the program fails to start, check that:
• the dishwasher is connected to the electrical power supply;
• there is no power failure;
• the water tap is open;
• the dishwasher door is properly closed.
If water remains inside the dishwasher, check that:
• the drain hose is not kinked;
• the drain siphon is not obstructed;
• the dishwasher filters are not clogged.
If the dishes are not being cleaned properly, check that:
• the correct amount of detergent has been added;
• there is regenerating salt inside the special container;
• the dishes are being loaded correctly;
• the selected program is suitable for the dish types and their degree
of soiling;
• all the filters are clean and positioned correctly;
• the spray arm nozzles are not obstructed;
• there is no object obstructing the rotation of the spray arms.
User instructions
If the dishes fail to dry or remain dull, check that:
• there is rinse aid inside the special container;
• the rinse aid dispenser setting is correct;
• the detergent used is of good quality and has not lost its
effectiveness (for example, through incorrect storage, with the box
left open).
If the dishes show signs of streaking, staining, etc., check that:
• the rinse aid dispenser setting is not too high.
If there are visible traces of rust inside the tank:
• the tank is made of steel, and therefore any rust marks are due to
external elements (fragments of rust from the water pipes, pots,
cutlery, etc.). Special products are commercially available t o
remove such marks;
• check that the amount of detergent being used is correct. Certain
detergents can be more corrosive than others.
• check that the cap of the salt container is securely closed, and that
the water softening setting is correct.
If after following the above troubleshooting instructions the problem
persists, call the nearest After-Sales Centre.
WARNING: any operations performed on the appliance by
unauthorised persons are not covered by the warranty and shall be
paid for by the user.
TECHNICAL DATA
Width
Depth measured flush with the
outer edge of the control panel
Height (depending on models)
Capacity
Water supply pressure
Electrical characteristics
User instructions
597 ÷ 599 mm
Free standing: 600 mm
Semi-integrated: 590 mm - Fully integrated: 570 mm
Free standing: from 850 mm to 870 mm
from 890 mm to 910 mm
Semi-integrated and fully integrated: from 820 mm to 870 mm
from 860 mm to 910 mm
12 Standard place settings
min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar)
See rating plate
115
125
Misurarel’altezzadelpannellocomandi;farecoinciderel’indicerelativoatalevaloreconilprofilosuperioredellaportainlegno;tracciareilposizionamentodegliagganciporta.
Measuretheheightofthecontrolpanel;bringthemarkrelatingtothisvalueintolinewiththetopedgeofthewoodendoor;markthepositionsofthedoorconnections.
Measurerlahauteurdupanneaudecommandes;fairecoïnciderl’indexrelatifàcettevaleuravecleprofilsupérieur delaporteenbois;tracerlepositionnementdescrochetsdelaporte.
DieHöhedesBedienfeldsmessen;DiediesemWertentsprechendeMarkierungmitdemoberenProfilderHolztürzurDeckungbringen;DiePositionderTüraufhängungenanzeichen.
Meetdehoogtevanhetbedieningspaneel;laatdemarkeringdiebijdiewaardehoortovereenstemmenmethetbovensteprofielvandehoutendeur;tekendepositievandedeurhengselsaf.
Medirlaalturadelpaneldemandos;hacercoincidirelíndicecorrespondienteadichovalorconelperfilsuperiorde lapuertademadera;trazarelposicionamientodelasbisagrasdelapuerta.
Meçaaalturadopaineldecomandos;façacomqueoindicadorrelativoaestevalorcoincida comoperfilsuperiordaportademadeira;marqueaposiçãodosganchosparaporta.
115
125
135
145
155
ATTENZIONE:
Montarelaportaeregolarelatensionedelle
mollelateraliprimadell’installazione.
Solosualcunimodelli
Certainmodelsonly
Seulementsurcertainsmodèles
nurbeieinigeModellen
Sóloenalgunosmodelos
alleenindienvantoepassing
SUPERFICIEINTERNA
SURFACEINTERNE
INNERSURFACE
INNENFLACHE
LATOSUPERIORE
BORDSUPERIEURE
UPPEREDGE
OBERKANTE
135
145
155
WICHTIG:
Türmontieren,TürfedernvorEinbau
einstellen.
IMPORTANT:
Doortemplate,donotdestroy.Fitdoorand
adjusthingetensionbeforeinstallation.
ATTENTION:
Apresmontàgedelaporte,reglerlatension
desressortslaterauxavantl’installation.
Solosualcunimodelli
Certainmodelsonly
Seulementsurcertainsmodèles
nurbeieinigeModellen
Sóloenalgunosmodelos
alleenindienvantoepassing
Regolazionevitetensionemolle(13)
Coperturafotocontappoindotazione(14)
DoorspringAdjustementdevice(13)
Coveringofholeusingcapprovided(14)
Réglagedesressortsdelaporte(13)
Couverturedutrouaveclebouchonfourni(14)
VorrichtungfürdieEinstellungderSpannungderTürfedem(13)AbdeckendesLochsmitdemmitgeliefertenStopfen(14)
ATENÇÃO:
Antesdainstalação,monteaportae
reguleatensãodasmolaslaterais.
IMPORTANTE:
Montarlapuertayregularlos
muellaslateralesantesdelainstalación.
10
1
11
8
9
13
NOTA:N.B.:REMARQUE:
ANMERKUNG:
NOTA:
Solamentealcunimodellisonodotatidiunodeidispositivisottoillustrati.Onlysomemodelsareequippedwithoneofthetwodevicesillustratedbelow.seulquelquesmodèlessontmunisdel’undedeuxdispositifsillustrésci-dessus.
NureinigeModelleverfügenübereinederbeidenuntendargestelltenEinrichtungen.NOTABENE:NOTA:
uitsluitendbepaaldemodellenzijnuitgerustmetéénvandetweeonderstaandafgebeeldeinrichtingenSóloalgunosmodelosestánequipadosconunodelosdosdispositivosqueseilustranacontinuación.
Sóalgunsmodelosestãoequipadoscomoudosdoisdispositivosilustradosabaixo
1/2”
3/4”
SW32
3/4”
Cuø10
MIN
40cm
Loading...