Smeg PA106SX User Manual

Contents

1 INSTRUCTIONS FOR SAFE AND PROPER US 2 POSITIONING OF THE HOB _________________________________________________6 3 GAS CONNECTION_______________________________________________________10 4 ELECTRICAL CONNECTION _______________________________________________11 5 ADAPTING TO DIFFERENT TYPES OF GAS___________________________________12 6 FINAL OPERATIONS______________________________________________________14 7 DESCRIPTION OF THE CONTROLS _________________________________________16 8 USING THE HOB _________________________________________________________17 9 CLEANING AND MAINTENANCE ____________________________________________18 10 PROBLEMS AND CAUSES________________________________________________19

Thank you for choosing our product.

We advise you to read this manual carefully. It contains all necessary instructions for maintaining unaltered the appearance and functional qualities of the hob.

INSTRUCTIONS FOR THE INSTALLER: these are for the authorised persons wh

must carry out a suitable check of the gas system, install the appliance, set i functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice, description of th commands and the correct procedures for cleaning and maintenance of the appliance.

_______________________________4

1 INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE

MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. INSTALLATION MUST BE CARRIED OUT BY AUTHORISED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: COOKING AND

HEATING-UP OF FOOD. ALL OTHER USES ARE CONSIDERED IMPROPER. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE THE

VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED

ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE SOCKET

MUST BE THE SAME TYPE AND MUST CONFORM TO CURRENT REGULATIONS.

NEVER UNPLUG BY PULLING ON THE CABLE.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST

OF THE COOKING HOB, FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION "ZERO"

(OFF) WHEN YOU FINISH USING THE HOB.

THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND

MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. A COPY OF THE PLATE IS ENCLOSED WITH THIS BOOKLET AND SHOULD BE STICKED IN THE FRAME IN THE INNER COVER. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT.

DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE COOKING HOB GRIDS.

Introduction

DO NOT USE PANS OR GRIDDLE PLATES THAT EXTEND BEYOND THE

EXTERNAL PERIMETER OF THE HOB.

THE APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR

INFIRM PERSON WITHOUT SUPERVISION. YOUNG CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE.

REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE

COLLECTION CENTRE.

WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS,

IT SHALL NOT BE USED AS A SPACE HEATER.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS

IN OPERATION.

The manufacturer declines all responsibility for damage to persons or things cause

by non-observance of the above prescriptions or by interference with any part of th appliance or by the use of non-original spares.

Introduction

Instructions for the installer

Create an opening with the dimensions shown in the figure in the top surface of the

2 POSITIONING OF THE HOB

It is the law that all gas appliances are installed by authorised persons.

Clearance around the appliance must comply with the requirements of AGA601. The following operation requires building and/or carpentry work so must be carrie out by a competent tradesman. Installation can be carried out on various material such as masonry, metal, solid wood or plastic laminated wood as long as they ar heat resistant (T 90°C).

2.1 Attachment to the support structure

counter, keeping a minimum distance of 50 mm from the rear border. This appliance is classified as “type Y” in relation to fire hazards and can therefore be mounted against walls higher than the work surface on condition that a certain distance “X” be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating. Make sure there is a minimum of 600 mm between the hot plate flames and any shelf that may be installed directly above them. In case of installation on a hollow compartment with doors, a separating panel has to be placed under the hob. Keep a minimum distance of 10 mm between the bottom of the unit and the panel surface. The panel has to be easily removable to allow access in the event of technical service.

Instructions for the installer

Carefully position the insulation gasket (supplied) on the external perimeter of the

hole made in the top surface (see figures below) and try to make it stick to the entire surface by applying light pressure with your hands. Refer to the distances shown in the figure for the model to be installed, keeping in mind that for both models the long front side has to skim the hole. Secure the hob to the counter with brackets A (supplied). Carefully trim any excess from border B of the gasket. The distances in the following drawing refer to the hole on the inner side of the gasket.

The diagram below shows the exact positions of the holes to be used for clamping the hob to the top correctly.

Overall dimensions: location of gas and electrical connection points (all measures in mm).

60 cm

A 45 105 105 B 290 340 470 C 45 45 45 D 45 45 65

hob

70 cm 100 cm

hob hobs

Instructions for the installer

Extract from AS5601

2.2 Clearance above and around domestic appliances

REQUIREMENTS 1 Overhead clearances – (Measurement A)

Range hoods and exhaust fans shall be installed in accordance with the

manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or, for an overhead exhaust fan, 750 mm.

Any other downward facing combustible surface less than 600 mm above the

highest part of the hob shall be protected for the full width and depth of the cooking surface area in accordance with Clause 5.12.1.2. However, in no case shall this clearance to any surface be less than 450 mm.

2 Side clearances – (Measurements B & C) Where B, measured from the periphery of the nearest burner to any vertical

combustible surface, is less than 200 mm, the surface shall be protected in accordance with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for the full dimension (width or depth) of the cooking surface area. Where the cooking appliance is fitted with a ‘splashback’, protection of the rear wall is not required.

3 Additional requirements for Freestanding and Elevated Cooking Appliaces –

(Measurements D & E)

Where D, the distance from the periphery of the nearest burner to a horizontal

combustible surface is less than 200 mm, then E shall be 10 mm or more, or the horizontal surface shall be above the trivet.

+ 14 hidden pages