Smeg LSA6544X2 User manual [GB]

INSTRUCTION MANUAL

GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS

Contents

1. Description of the controls ________________________________ 2

2. Operating instructions ___________________________________ 14

3. Cleaning and maintenance _______________________________ 30

4. Troubleshooting _______________________________________ 34

Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher. The individual sections are laid out to provide you with a step-by-step guide to all your appliance's functions; the texts are easy to understand and are complete with detailed illustrations. Recommendations are given for the correct use of the baskets, spray arms, containers, filters, washing programs, and for operating the controls. Following the cleaning instructions provided here will keep your dishwasher's performance at peak levels in the long term. This user-friendly manual will provide answers to all your questions about use of the dishwasher.

USER INSTRUCTIONS: these consist of recommendations for using the appliance, a description of its controls and of the correct cleaning and maintenance procedures.

INFORMATION DISPLAY (9)

1. Description of the controls

User instructions

1.1 Front panel

The ON/OFF is on the top edge of the panel, and all the dishwasher’s other controls and monitoring devices are on the central display. Programming and option selection are only possible with the door

closed.

NOTA:

The displays illustrated in the instruction manual are purely guideline; symbols, programs and options may vary depending on the model purchased.

The 4-figure

informs the user about the program delay, time remaining (washing cycle duration) and alarms.

User instructions

1 ON/OFF BUTTON 2 SELECTION PROGRAMS BUTTON 3 START/PAUSE BUTTON 4 PROGRAMS LIGHTS 5 PHASES/PROGRAM LIGHTS

WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT

The light flashes to indicate that the appliance is in “water hardness adjustment” mode.

SALT WARNIN LIGHT

Illumination of this light denotes a regenerating salt warning level.

7 NO RINSE AID LIGHT 8 OPTIONS 9 INFORMATION DISPLAY

PROGRAMS TABLE

User instructions

<<OPTIONS(8)>>

Depending on the model, this zone may contain one or more of the following options, identified by the relative symbols and described in more detail in the relevant sections of the manual. It is not possible to select any options when the soak program is being used. All options except "Flexi Tabs" are disabled at the end of the wash cycle. To disable the “Flexi Tabs” option, press the relative button (the light goes out).

Flexi Tabs

Option recommended for the use of multi-function tablet detergent.

HYCLEAN

Increases the temperature of the final hot rinse to 70°C to ensure a further reduction in the bacteria level.

Spread HALF LOAD WASH

Allows washing of just a few dishes placed in both baskets.

PROGRAM DELAY

Allows the program to be set to start with a delay of up to 9, 12 or 24 hours, depending on the model.

QUICK TIME

Select this option together with any washing program (except the soak program) to SHORTEN the cycle.

ENERSAVE

Indicated option for save energy.

The manual contains the programs table for several models. To find the table for your dishwasher, compare the program symbols at the top of the table with those on your control panel.

User instructions

PROGRAMM

NUMBER &

SYMBOL

SOAK

GLASS

DELICATE

ECO (*)

EN 50242

AUTO

40-50

AUTO

60-70

IEC/DIN***

SUPER

****

LOAD CROCKERY AND

CUTLERY

Pans and dishes awaiting

completion of the load.

Delicate dishes with light dirt.

Delicate dishes with normal dirt.

Dishes with normal dirt, even

with dried-on residues.

Pans and dishes with normal

dirt, washed immediately after

use.

Pans and dishes with normal

dirt, even with dried-on residues.

Very dirty pans and dishes,

even with dried-on residues.

PROGRAM

PROGRESS

Cold prewash

Wash at 45°C Cold rinse Rinse at 70°C Dry

Cold prewash Wash at 45°C Cold rinse Rinse at 70°C Dry

Wash at 45°C Cold rinse Rinse at 55°C Dry

When the "

recognises the type of dirt and automatically adjusts the

When the "

recognises the type of dirt and automatically adjusts the

AUTO

washing parameters as appropriate.

AUTO

washing parameters as appropriate.

Hot prewash Wash at 70°C Cold rinse (2) Rinse at 70°C Dry

DURATION

MINUTES

(1)

CONSUMPTION

WATER LITRES

15 3,5 0,02

9,5 1,10

12,5 1,1

** **

" program is selected, the dishwasher

155

15,5 1,60

IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.

If the dishwasher door is open or not properly closed, the washing cycle will not start.

POWER KWh (1)

User instructions

QUICK TIME PROGRAMS

(see relevant section for explanation of functioning modes)

PROGRAMME

NUMBER E

SYMBOL

RAPID 27’

DELICATE

QUICK

ECO

QUICK

DAILY QUICK

NORMAL

QUICK

STRONG and

FAST

LOAD CROCKERY AND

CUTLERY

Dishes with light dirt,

washed immediately after

use

Dishes with normal dirt,

even with dried-on residues

Dishes with normal dirt,

washed immediately after

use.

Dishes with normal dirt,

washed immediately after

use.

Dishes with normal dirt,

even with dried-on residues

Mixed dishes with normal dirt

without dried-on residues.

DURATION

MINUTI

(1)

PROGRAM

PROGRESS

Wash at 38°C Rinse at 50°C

Cold prewash Wash at 50°C Cold rinse Rinse at 70°C

Cold prewash Wash at 60°C Cold rinse Rinse at 70°C

Wash at 70°C Cold rinse Rinse at 70°C

Cold prewash Wash at 70°C Cold rinse Rinse at 70°C

Wash at 65°C Cold rinse Rinse at 70°C

CONSUMPTION

WATER LITRES

6,5 0,70

12,5 1,15

12,5 1,40

9,5 1,40

13 1,40

9,5 1,35

IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.

The washing cycle will not take place if the dishwasher door is left open or not properly closed.

POWER KWh (1)

User instructions

NOTES AND REFERENCES

Only

EN 50242

ENERSAVE

IEC/DIN

ENERSAVE

be enabled

20g

dispenser

10g

run the soak program with half loads. Options cannot be used with the soak program. The ENERSAVE option cannot be used with soak, ultra clean, or any programs

which do not include the final drying stage.

Standard programme under

. The

option must

enabled.

** See information sheet provided

***

Reference program for laboratories: Detergent:

****

reference programme. The

option must

in the

the door or tablet. Configuration: see photo in “Using the baskets”.

(1) The cycle duration and power consumption may vary according to the water

and room temperatures, and the type and amount of dishes.

(2) 1 or 2 cold rinses depending on the model.

REFERENCES for the ENERGY LABEL supplied with the dishwasher:

- Annual energy consumption is based on 280 standard wash cycles with cold water and consumption of low-energy operating modes. Actual consumption depends on the way in which the appliance is used.

- Water consumption is based on 280 standard wash cycles. Actual consumption depends on the way in which the appliance is used.

- Information refers to the EN 50242 STANDARD programme (identified in the programmes table), which is the most effective in terms of combined energy and water consumption. The programme is recommended for dishes with a normal level of dirt.

- Energy consumption in “sleep” mode = 0.02 W.

- Energy consumption in “on” mode = 1.5 W.

- Drying efficiency class on a scale from “G” (minimum efficiency) to “A” (maximum efficiency).

SWITCHING ON

PROGRAMMING

PROGRAM SELECTION

(2)

User instructions

1.2 Washing programs

The dishwasher is equipped with a control panel, described in chapter

"3. Description of the controls", from which it is possible to carry out all the power switch-on, switch-off and programming operations.

Before starting a washing program make sure that:

• The water supply tap is open.

• The correct amount of detergent has been added to the

dispenser.

• The baskets have been correctly loaded.

• The spray arms are able to rotate freely and without

obstruction.

• The dishwasher door is securely closed.

When the ON/OFF button (1) is pressed, the dishwasher switches on.

Programming operations are only possible with the door closed.

Press the

button

several times until the light of the program required comes on. As the user scrolls through the programs the INFORMATION DISPLAY (9) will show the scheduled duration of each program, and the PHASES/PROGRAMS lights (5) will indicate the washing phases it includes.

User instructions

STARTING THE PROGRAM

END OF PROGRAM

INTERRUPTION A PROGRAM

To start the dishwasher, press the START/PAUSE button (3) for a few seconds, until the light of the first phase of the selected program starts to flash (confirmation beep). As the program runs, the PHASES/PROGRAM lights (5) will indicate the current cycle status.

The light of the phase in progress will flash, while the lights of the

subsequent phases remain on.

At the end of the program, a short beep sounds, the word “End on the DISPLAY (9) and the PHASES/PROGRAMS (5) lights flash.

Pressing the SELECTION PROGRAMS (2) button clears the word “End from the display and the dishwasher is ready for a new cycle.

To interrupt a program in progress:

• press the START/PAUSE button (3 ) for a few seconds; the light of

the phase in progress remains on and the light of the program in progress flashes (confirmation beep);

• you may now restart the program by pressing button (3) again until it

restarts, or change or annul the program (see "C

PROGRAM", or "ANNULLING A PROGRAM").

End” appears

EndEnd

End”

EndEnd

HANGING A

CHANGING

PROGRAM

ANNULLING A PROGRAM

ENERSAVE

automatically every time

User instructions

To change the running program it is necessary:

• to interrupt the running program (see “INTERRUPTION A PROGRAM”);

• select the new program;

• start the program (see “STARTING THE PROGRAM”).

To annul the program

• press the START/PAUSE button (3 ) for a few seconds; the light of

the phase in progress remains on and the light of the program in progress flashes (confirmation beep);

• Keep the START/PAUSE button (3) pressed until the PROGRAM

PHASES lights (5) go out (confirmation beep). “

” will appear on

P0 P0

the DISPLAY and pump-out of the water in the tank will begin, ending the program at the point where it was interrupted. When the operation is complete, the PHASES/PROGRAM LIGHTS (5) flash.

The water in the tank will be pumped out and the program will end at the

point where it was interrupted. When the operation is complete, the PROGRAM PHASES lights (5) flash.

In case that the door is opened during the operation, to the next door closing it is going to be necessary to start the program as shown in paragraph “ point in which it was interrupted.

TARTING THE PROGRAM”. The program will resume from the

In case that the tub temperature is higher than 50°C the program will start about 60 seconds later.

This option can be selected with the wash programme of choice to further reduce energy consumption. Drying is aided by a special device that automatically releases the door, which opens slowly and smoothly by a few centimetres. This ensures perfect drying and greater control of rinsing temperatures, which can be kept at lower levels for significant energy saving. Once the door has opened, the end of the wash cycle is indicated by a short beep. Enersave is activated

a wash cycle is selected (except for programs that do not include the final drying phase; see programs table) and can be disabled before the program is started. Flexi Tabs, once selected, remains enabled until intentionally disabled.

+ 25 hidden pages