Smeg LBS645 User Manual
Washing machine
LBS 645
12
IT
Contents
Specifications of your Washing Machine
Warnings
Installation
Preparation
Program Selection and Operating Your Machine
Maintenance and Cleaning
> 4
> 5
> 6
> 8
> 9
> 13
2
23
IT
Your Washing Machine
Detergent Drawer
Control panel
Tabletop
Adjustable feet
Front door
Filter cover
3
34
IT
In order to improve the product quality, modifications can be made in the specifications without prior notice.
The illustrations in this guide are schematic and may not exactly match with your
product.
The values that are declared in the markings on your product or in the printed
documents accompanying are obtained in a laboratory environment according to the
related standards. These values may vary according to the usage of the product and
environmental conditions.
Specifications of your Washing Machine
Models
LBS 645
Maximum dry laundry capacity (kg.) 4.5
Height (cm.) 85
Width (cm.) 60
Depth (cm.) 45
Net Weight (kg.) 58
Electricity (V/Hz.) 230/50
Total Current (A) 10
Total Power (W) 2350
Washing -rinsing cycle (cyc/min) 52
Spinning cycle (max cyc/min) 600
4
45
IT
Warnings
• This product is designed for home
use.
• Your washing machine is adjusted to
230V.
• If the fuse in your house is less than
16A than have a certified electrician
deploy an 16A fuse.
• In case of transformer or non-transformer use, grounding installation
must be performed with a licensed
electrician. Any use before grounding
is not our responsibility.
• Never place your machine over a carpet covered floor. Otherwise electrical
parts of your machine may overheat.
This may cause malfunction of your
machine.
• Make sure hot and cold taps are
connected correctly. Otherwise your
laundry may come out hot and torn .
• Please call certified service for a failure of electric plug / cable.
• Be careful about your water hoses are
not old. Do not use old / torn water
hoses. This may cause stain in your
laundry .
• At first use, washing must be performed at Cotton 90°C program without loading with laundry for getting
your machine ready for washing.
• Performance of your washing machine depends on the quality of water
and hygiene compound used. If low
quality and unfitting cleaning material
is used the stains will be fixed. Before
washing your laundry with stain keep
your attention on cleaning the laundry
as explained in following pages.
• This is period of keeping spare parts
for your machine to operate. Because
of quality control procedures there
might be little amount of water in your
machine. This does not have any
damage to your machine.
• Your machine is programmed for starting operation again when electricity
is off and on afterwards. You can
not press On / Off button to cancel
program. Machine will go on program
when electricity is on. To CANCEL the
program press >Start/Pause/Cancel<
button for three seconds. (See. Cancelling a program)
If “Door” led on program progress
display is blinking program selection
knob is middle position. In this case
turn the knob and adjust it again. If
the warning continues call authorized
service.
• After your machine starts operation, if
Start/Pause/Cancel key starts blinking
than door is not locked. Open and
close the door again begin washing
program again.
• If the “washing” led on the program
progress display is blinking either
there is no water or tap is off. Check
your taps. Turn your machine off and
on. If the problem persists unplug
your machine, turn off tap water and
call authorized service.
• If program is started and program
selection can not be performed your
machine might be in protection mode
due to infrastructure problem (voltage,
water pressure, etc.) Press and hold
the > Start/Pause/Cancel < button for
3 seconds in order to switch machine
to factory settings.
• Most of the warnings resulting in calling an authorized service are due to
infrastructure problems. For this reason applying to an Authorized Service
is recommended.
5
Loading...