Smeg HB6422BRU Operating Manual

Installation and Operating Instructions

Built-In Gas Cooktops

To avoid the risk of accidents or damage to the Gas Cooktops,
it is essential to read these operating instructions
before it is installed or used for the rst time.
And please keep this manual for later reference.

HB6422BRU

P/No.: MFL62060313

www.lg.com

Contents

Introduction ................................................................................. 3

1. Instructions for safe and proper use ...................................... 3

Instructions for the installer ...................................................... 5

2. Positioning of the hob ............................................................ 5

3. Electrical connection .............................................................. 7

4. Gas connection ...................................................................... 8

5. Adaptation to different types of gas ...................................... 10

6. Final operations ................................................................... 13

Instructions for the user .......................................................... 15

7. Using the hob ....................................................................... 15

8. Cleaning and maintenance .................................................. 17

These instructions are valid only for end user countries whose
identification symbols appear on the cover of this manual.

INSTRUCTIONS FOR THE INSTALLER: these are for the
authorised person who must carry out a suitable check of the gas
system, install the appliance, set it functioning and carry out an
inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,
description of the commands and the correct procedures for
cleaning and maintenance of the appliance.

2

Introduction

1. Instructions for safe and proper use

This manual is an integral part of the appliance and therefore must
be kept in its entirety and in an accessible place for the whole
working life of the cooking hob. We advise reading this manual and
all the instructions therein before using the cooking hob. Also keep
the series of nozzles supplied. Installation

must be carried out by qualified personnel in accordance with the
regulations in force. This appliance is intended for domestic uses
and conforms to current regulations in force. The appliance has
been built to carry out the following functions: Cooking and

heating-up of food. All other uses are considered improper.
The manufacturer declines all responsibility for improper use.

Do not leave the packing in the home environment. Separate the
various waste materials and take them to the nearest special
garbage collection centre.

It is obligatory for the electrical system to be grounded according to
the methods required by safety rules.

The plug to be connected to the power cable and the socket must
be the same type and must conform to current regulations.

Never unplug by pulling on the cable.

Immediately after installation carry out a brief inspection test of
the cooking hob, following the instructions below. Should the
appliance not function, disconnect it from the supply and call the
nearest technical assistance centre.

Never attempt to repair the appliance.

Always check that the control knobs are in the position
“ZERO”(OFF) when you finish using the hob.

3

Introduction

The identification plate, with technical data, serial number and
marking is clearly visible under the casing.

The plate on the casing must not be removed.

Before connecting the device, make sure that it has been regulated for
the type of gas that will feed it, checking the label under the casing.

Do not put pans without perfectly smooth and flat bottoms on the
cooking hob grids.

Do not use recipients or griddle plates that extend beyond the
external perimeter of the hob.

The hob is to be used by adults only. Do not let unsupervised
children play with the hob.

This appliance is designed for cooking food and it shall not be used
as a space heater.

Do not spray aerosols in the vicinity of this appliance while it is in operation.

The manufacturer declines all responsibility for damage to persons or things
caused by non-observance of the above prescriptions or by interference with
any part of the appliance or by the use of non-original spares.

THIS APPLIANCE IS MARKED ACCORDING TO EUROPEAN DIRECTIVE 2002/96/
EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). THIS
GUIDELINE IS THE FRAME OF EUROPEAN-WIDE VALIDITY OF RETURN AND
RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT.

DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE
APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.

DO NOT MODIFY THIS APPLIANCE

4

Instructions for the installer

2. POSITIONING OF HOB

The following operation requires building and/or carpentry work so
must be carried out by a competent tradesman.
Installation can be carried out on various materials such as
masonry, metal, solid wood or plastic laminated wood as long as
they are heat resistant (T 90°C).
Never use silicone or other insulating products when installing the
appliance; use only the rubber gasket provided.

2.1. Attachment to support structure

Create an opening with the dimensions shown in the figure in the
top surface of the counter, keeping a minimum distance of 50 mm
from the rear border. This appliance can therefore be mounted
against walls higher than the work surface on condition that a
certain distance “X” be kept between the appliance and the wall as
shown in the figure so as to avoid damage from overheating.
Make sure there is a minimum of 750 mm between the hot plate
flames and any shelf that may be installed directly above them.

5

Instructions for the installer

Accurately position the gasket provided all around the outer edge of
the hole in the top surface as shown in the figures below, pressing it
down so as to make it adhere properly. For measurements, refer to
the figure depending on the hob model to be installed, bearing in
mind that in both models the front and rear sides must skim the hole.
Secure the hob to the counter with brackets A (supplied). Carefully
trim any excess from border B of the gasket. The distances in the
following drawing refer to the hole on the inner side of the gasket.

In case of installation on a hollow compartment with doors, a
separating panel has to be placed under the hob. Keep a minimum
distance of 10 mm between the bottom of the unit and the panel
surface. The panel has to be easily removable to allow access in
the event of technical service.

6