Page 1
INSTALLATION REQUIREMENTS
WD6010 – GW6010 – WD7010 – GW7010
Pag. 1 - 5
INSTALLATION REQUIREMENTS
WD6010 – GW6010
WD7010 – GW7010
SMEG S.p.A. thank you for choosing this product.
Pre-installation operations (to be performed by the client):
room preparations (as needed)
pre-installation of properly operating systems, in compliance with the requirements and
regulations in force
positioning of the machine
Refer to this manual for detailed instructions on the steps mentioned above.
SMEG S.p.A. declines responsibility for damage to persons or property resulting from improperly
regulated or defective systems or for any installation of the appliance and/or accessories performed by
unauthorized personnel.
Any operation performed on the appliance by unauthorized personnel will invalidate the warranty.
19 561 0121 07 – IT
15 / 12 / 16
New mod. exp. – new document layout: part 1 descriptive, part 2 schematic with specific code.
19 561 0121 05 - IT
14 / 10 / 16
Added 7010 models and some value corrected
19 561 0121 04 - EN
06 / 06 / 16
Specified installation environment conditions. Added RS232 and LAN in the scheme.
19 561 0121 02 – EN
11 / 01 / 16
Specified cold water limits and added notes for the optional drain pump
19 561 0121 01 – EN
09 / 12 / 15
Update: hydraulic and electric connection from the upper side, Except the models provided with heating tanks
(«boiler»). Improved prescription regarding supply water.
REV. DOC.
DATE
NOTES
Page 2
INSTALLATION REQUIREMENTS
WD6010 – GW6010 – WD7010 – GW7010
Pag. 2 - 5
ELECTRICAL SYSTEM REQUIREMENTS
CAUTION
It is essential that the electrical system to which the machine is connected complies with current regulations.
All electrical testing operations and equipment installation should be made by qualified and trained personnel.
The designated personnel is responsible for ensuring the safety and efficiency of earth connection.
Components must always be replaced with genuine spare parts.
Refer to the Technical Data sheet to recognize the device’s electrical characteristics and connection requirements.
The device is supplied with a cable with insulated wire terminals; it is not supplied with a plug. The electrical connection of
the device must be carried out with a permanent connection.
CIRCUIT-BREAKER
A CIRCUIT-BREAKER must be installed for each appliance.
Circuit-breaker characteristics:
a. Omnipolar: must break all live conductors;
b. Easily accessible to the user;
c. Easily operated (no additional tools required);
d. Located in close proximity to the appliance;
e. Clearly marked as the appliance circuit-breaker
The same specifications apply to the main switch on the machine: it must be easily accessible. Do not place
objects in a way that limits accessibility.
A PROTECTIVE DEVICE specifically for the appliance (e.g. magneto thermal breaker or fuse on every phase, with
appropriate dimensions based on the electrical characteristics indicated) should be installed in the room’s
electrical panel.
Page 3
INSTALLATION REQUIREMENTS
WD6010 – GW6010 – WD7010 – GW7010
Pag. 3 - 5
Technical data
Water connections
Microbial contamination limits - Minimum microbiological
quality required:
“drinking water type” (ref. limits
provided by European Directive
98/83/CE)
"CW" COLD WATER
Connection:
3/4" maschio-male - DN20
Min -Max flow rate:
4 - 12 l/min (0,88-2,64 gal/min)
Min - flow pressure:
100 kPa (1,0 bar)
Max. pressure:
600 kPa (6,0 bar)
Min-Max. temperature:
8°C / 25°C ( 46°F / 75°F)
Max. hardness:
8 °f (4,5 °d)
Ferro Max - Fe2+ / Fe3+ [max]
0,5 ppm
pH:
7÷8
"HW" WARM WATER
Connection:
3/4" maschio-male - DN20
Min/Max flow rate:
4 - 12 l/min (0,88-2,64 gal/min)
Min. flow pressure:
100 kPa (1,0 bar)
Max. pressure:
600 kPa (6,0 bar)
Max. temperature:
60°C (140°F)
Max. hardness:
8 °f (4,5 °d)
Fe2+ / Fe3+ [max]
0,5 ppm
pH:
7÷8
"DW" DEMI WATER
Connection:
3/4" maschio-male - DN20
Min/Max flow rate:
4 - 12 l/min(0,88-2,64 gal/min)
Min. flow pressure:
100 kPa (1,0 bar)
Max. pressure:
600 kPa (6,0 bar)
Min-Max. temperature:
8°C / 60°C ( 46°F / 140°F)
Max. hardness:
0 °f (0 ppm CaCO3)
Max. conductivity / pH:
30 µS/cm / 5÷8 pH
TDS max
40 mg/l
Note: if local-regional requirements are more stringent than those prescribed above, the local
requirements shall be followed. It remains the user's responsibility to provide water supply that
comply with the requirements.
Page 4
INSTALLATION REQUIREMENTS
WD6010 – GW6010 – WD7010 – GW7010
Pag. 4 - 5
Electrical connections
"EC" Electrical connections
Standard 400V connection three-phases with neutral
Standard Voltage:
400V 3N~ / PE / 50Hz / 24A
Electrical protection required:
3P+N, 32 A
Cable and min. section:
5 x 6 mm2
Power:
13 kW
230V connection three-phases without neutral
Configurable Voltage:
230V 3~ / PE / 50Hz / 36A
Electrical protection required:
3P, 40 A
Cable and min. section:
4 x 6 mm2
Power:
13 kW
Drain and exhaust
"EX" EXHAUST DUCT
Connection:
ø 50 mm ( 2 in)
Peak flow rate:
approx.220-250 m3/h
Max. temperature:
95 °C (203°F)
"FD" DRAIN FLOOR (standard)
Connection:
ø 50 mm ( 2 in)
Peak flow rate:
50 lt/min (6,6 gal/min)
Max. height:
floor level (0mm)
Max. temperature:
95 °C (203°F)
"D" DRAIN WALL (optional)
Connection:
ø 40 mm (1,6 in)
Peak flow rate:
30 lt/min (6,6 gal/min)
Altezza max. - Max. height:
800 mm (32 in)
Temperatura max. - Max. temperature:
95 °C (203°F)
Others
WEIGHTS
Model
WD6010,
GW6010
WD7010,
GW7010
Total net max:
280 kg/daN
300 kg/daN
Total gross max:
310 kg/daN
340 kg/daN
Max. on working:
380 kg/daN
400 kg/daN
Floor load:
600 kg/m2
(daN/m2)
600 kg/m2
(daN/m2)
ENVIRONMENT
Temperature min-max
T = 10 - 40 °C (50-104°F)
Umidity max.:
80% for temperatures up to 31°C
(88°F) with a linear drop to 50%
humidity at 40°C (104°F)
Minimum diffused illumination required
300 lx
Maximum altitude
1000m. s.l.m.
heat emission to atmosphere (excluding steam exhaust)
Max 1000W – 3500 BTU/hr
Noise level emission:
< 66 dB (A)
Page 5
INSTALLATION REQUIREMENTS
WD6010 – GW6010 – WD7010 – GW7010
Pag. 5 - 5
NOTES
1) It is the customer’s responsibility to insure that the specified pressure ranges are respected (water
mains and, if applicable, steam and air pressure). The pressure has to be measured at the point of
connection to the device.
2) It is customer’s responsibility to provide, if necessary, shock arrestors and / or pressure regulators
to eliminate water hammer conditions.
3) It is customer’s responsibility to provide shutoff valves for incoming cold, hot, demineralized water,
and steam and air (optional). The valves must always be easily accessible to the operator.
4) It is the customer’s responsibility to provide a proper drainage system based on the requirements of
the device and in accordance with national and local regulations. It is necessary to prevent backflow
to the device.
5) Steam exhaust: It is customer’s responsibility to ensure that the ducts are constructed to prevent
the accumulation of condensate. If the machine is connected to free discharge pipes for
steam/fume exhaust, condensation deposit in pipes must be prevented. Moreover, this section of
the machine must be equal to or higher than the given dimensions and there must not be areas
with condensation deposits. In case of fume extraction, the clearances as shown in the schemes
must be observed. At any rate the indicated flow rates must be observed and the materials must be
resistant to the expected temperatures.
6) Even in case of two or more machines installed side by side, the service area required must be
respected.
7) In case of double-door machines, it is customer’s responsibility to provide a barrier wall for the
separation between the loading side (unclean side) and the unloading side (clean side).
8) In the case of water loading taps placed near the top of the machine: it is necessary that the
position of the taps is suitably offset, with respect to the machine, to absolutely avoid water spills
on the device, in the connection and disconnection operations of the fittings.
Smeg S.p.A.
Instruments Division
Via Leonardo da Vinci, 4 – 42016 Guastalla (RE) Italy
Tel. +39 0522 8211 – Fax +39 0522 821 592
Servizio Clienti Assistenza Instruments +39 0522 184 85 95
e-mail: instruments@smeg.it - service.instruments@smeg.it - assistenza.instruments@smeg.it
www.smeg-instruments.com
Loading...