Smeg GW0160 Programs table [GB]

GW0160 Series

- PROGRAMS TABLE -

WARNING

This document is an appendix to the appliance's user manual and must be consulted together with the manual for proper, safe use of the device. It contains up-to-date information concerning the characteristics of the washing programs installed in the appliance. Due to changes made in response to improvements in products, the programs described here may differ from those described in the manual: in this case, only refer to the information provided in this document.

Programs may vary depending on the firmware version installed in the appliance. If in doubt, have Smeg authorised staff check on the appliance that the installed version is the same as the version stated in the table at the back of this document.

ABBREVIATIONS USED IN THE TABLE OF PROGRAMS

Demi: demineralised water, the type of water used in a specific phase of the program. Cold: cold mains water, the type of water used in a specific phase of the program. Load H2O: type of water while loading Holding time: Temperature extension INT: intensive - refers to programs which include particularly intensive washing phases. N.C.: "NOT CONTROLLED" - refers to the relatively short heating phases during which the heating elements are on but no target temperature value is set. PET: petroleum – refers to the program developed to wash glassware and items in general used to contain petroleum and its derivates. PLAST: plastics – refers to the program developed to wash plastics, with target temperatures generally suitable for washing plastic containers and other items for professional use. TD, Therm: thermal disinfection - phase during which the target temperature is kept above a target value for a specified time. The efficacy of the thermal disinfection process is indicated by means of parameter A0. In Smeg programs, the target value for a thermal disinfection process is always at least 80°C. Temp °C: Target temperature of the current phase. The temperature inside the tank is kept constant around the specified value for the time shown in the table. The phase during which

the temperature is held at the target value is called the EXTENSION phase. When no target temperature is indicated or the indication is (“0”), the heating elements are not activated (e.g. during a cold prewash or for cold rinses). Un: universal – a type of washing program designed to be particularly intensive. P1,P2: the code refers to the activation of the relative peristaltic pump, with dispensing of the liquid detergent associated to it. DD: powder dispenser. To use in alternative to P1. If you use the dispenser, the proper dosage should be carried out manually by the user at the beginning of the cycle. (The dispenser is only available in certain models of the GW0160 series, ref. to the manual for explanations).

PUMP

GW DEFAULT DOSAGE

[ml/litre]

DOSAGE FOR SERVICE PROGRAM 8

ONLY [ml/litre]

3-5 [g/litre]

VARIOUS NOTES:

WATER INTAKE: water intake for each phase is 9 litres. For program “8 Service” only, water intake is 6 litres for phases 1 and 2 and 9 litres for the rinse phase 3. Program “8 Service” only

comprises 3 phases and is generally used during installation, to prime the detergent intake lines correct and allow use of the device.

PHASE NUMBERING: a record of the parameters for the various cycle phases is maintained in the appliance’s memory. The first phase is numbered “PHASE 1”, the second “PHASE 2”, etc.

CYCLE TIME: the stated time for the complete cycle refers to standard test conditions: intake water pressure 3bar, cold water temperature 25°C, 3/N/PE 7kW three-phase electrical

connection, void washing chamber. The single-phase connection performs the activation of a single heating element instead of three, the cycle times are significantly longer.

PARAMETER A0

Parameter A0 is used by product standard UNI EN ISO 15883-1 to assign a numerical value to the thermal disinfection process. It is calculated mathematically using the formula:

z = 10°C - t = duration of time interval considered in seconds - T = load temperature in °C.

When calculating the parameter, only the time intervals during which the temperature is above 80°C are considered. For SMEG thermal disinfection programs, the calculation is simplified by only including the “extension” phase, when the temperature is kept constant with reference to the target value set.

PROCESSABLE LOAD: never exceed a total load of 23 kg to ensure good washing results. The items in the load must be positioned correctly, with no overlapping.

+ 1 hidden pages