Replacing The Light Bulb...................................................................................10
TRANSPORTATION AND CHANGING OF INSTALLATION POSITION..............11
Changing of Door Opening Direction................................................................11
BEFORE CALLING YOUR AFTER SALES SERVICE..........................................11
THE PARTS OF THE APPLIANCE AND THE COMPARTMENTS........................13
UK - 1 -
PART- 1.BEFORE USING THE APPLIANCE
Safety Instructions
• If the model contains R600a-see name plate under refrigerant (the coolant isobutane),
naturals gas that, is very environmentally friendly but also combustible. When
transporting and installing the unit care must be taken to ensure that none of the
refrigeration circuit components become damaged. In the event of damage avoid
naked flames or ignition sources and ventilate the room in which the unit is placed
for a few minutes.
Warning: Keep ventilation openings in appliance enclosure or in structure for building
in, clear of obstruction.
• Do not use mechanical devices or other artificial means to accelerate the defrosting
process.
• Do not use electrical appliances in the refrigerator or freezer compartment of the
appliance.
• If this appliance is to replace an old refrigerator with a lock; break or remove the lock
as a safety measure before storing it, to protect children while playing might lock
themselves inside.
• Old refrigerators and freezers contain insulation gases and refrigerant, which must
be disposed of properly. Entrust the disposal of a scrap unit categorically to
competence of your local waste disposal service and contact your local authority or
your dealer if you have any questions. Please ensure that the pipe of work of your
refrigerating unit does not get damaged prior to being picked-up by the relevant
waste disposal service.
Important note:
Please read this booklet before installing and switching on this appliance. The
manufacturer assumes no responsibility for incorrect installation and usage as described
in this booklet.
Conformity Information
• Tropical Class is defined for the environment temperatures between 16°C and 43°C
in accordance with the TS EN ISO 15502 Standards.
• The appliance is designed in compliance with the EN15502, IEC60335-1 /
IEC60335-2-24, 2004/108/EC standards.
UK - 2 -
Recommendations
Warning: Do not use mechanical devices or other means to accelerate the defrosting
process, other than those recommended by the manufacturer. Do not use electrical
appliances inside the food storage compartments of the appliance, unless they are of the
type recommended by the manufacturer. Keep ventilation openings, in the appliance
enclosure or in the built-in structure, clear of obstruction. Do not damage the refrigerant
circuit.
• Do not use adapters or shunts, which could cause overheating
or burning.
• Do not plug old, warped power supply cables.
• Do not twist and bend the cables.
• Do not allow children to play with the appliance. Children must
NEVER sit on drawers or hang from the door.
• Do not use sharp metal objects for removing ice on the freezer
compartment; they could puncture the refrigerator circuit and
cause unrepairable damage to the unit.
• Do not plug the power supply with wet hands.
• Do not place containers (glass bottles or tin containers) of liquids
into the freezer especially gassy liquids as they could cause the
container to burst during freezing.
• Bottles that contain a high percentage of alcohol must be sealed
well and placed vertically in the refrigerator.
• Do not touch the cooling surfaces, especially with wet hands as
you could be burnt or hurt.
• Do not eat ice, which have just been removed from the freezer.
• The appliance is not intended for use by people (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety. Children should be supervised to ensure that
they don’t play with the appliance.
• If the supply cord is damaged it must be replaced by the manufacturer or service
agent or similary qualified people in order to avoid a hazard.
UK - 3 -
Installation and Switching On The Appliance
• This appliance is connecting to 220-240V or 200-230V and 50 Hz. Please check
nameneplate of appliance and be sure voltage range suitable to your mains voltage.
• You can offer help from the service to install and switching on the appliance.
• Before making the connection to the power supply, ensure that the voltage on the
nameplate corresponds to the voltage of electrical system in your home.
• Insert the plug into a socket with an efficient ground connection. If the socket has no
ground contact or the plug does not match, we suggest you to call an authorised
electrician for assistance.
• The plug should be accessible after the appliance is positioned.
• Manufacturer is not responsible for failure to complete the ground
connection as described in this booklet.
• Do not place the appliance in direct sunlight.
• Do not use in open air and shall not be exposed to the rain.
• Place the refrigerator far from heat sources and in a wellventilated position. The refrigerator should be at least 50 cm
from radiators,gas or coal stoves and 5 cm far from electrical
stoves.
• Keep the top free for at least 15 cm.
• Do not place heavy and lots of things on the appliance.
• If the appliance is installed next to another refrigerator or freezer,
observe a miminum distance of 2 cm to prevent condensation.
• Do not put very (!) hot food or bowl on the top table. It can damage
the toptable.
• Fit the plastic wall spacers to the condenser at the back of the
refrigerator in order to prevent leaning to the wall for good
performance.
• The appliance must be stand firmly and level on the floor use
levelling-feet to compensate for an even floor.
• The outside of the appliance and the accessories inside should be cleaned with a
solution of water and liquid soap; the inside of the appliance with sodium bicarbonate
dissolved in lukewarm water. After drying replace all the accessories.
Before Switching On
• Wait after 3 hours before plugging the appliance in to the power to
ensure proper performance.
• There can be an odor when you first switch on the appliance. It will
disappear after the appliance starts to cool.
UK - 4 -
PART- 2.
THE VARIOUS FUNCTION AND POSSIBILITIES
Thermostat Setting
• Thermostat automatically regulates the inside temperature of the refrigerator
compartment and freezer compartment.By rotating the knob from position 1. to 5.,
colder temperatures can be obtained.
• « 0 » position shows thermostat is closed and no cooling is available.
• For short-term storage of food in the freezer compartment, you can set the knob
between minimum and medium position.(1-3)
• For long-term storage of food in the freezer compartment, you can set knop medium
position.(3-4)
Note that; the ambiant temperature, temperature of the freshly stored food and how
often the door is opened, affects the temperature in the refrigerator compartment. If
required,change the temperature setting.
• When you first switch on the appliance, for starting a suitable cooling, the appliance
should work 24 hours continuously until it cools down to sufficient temperature.
• In this time do not open the door so often and place a lot of food inside the appliance.
• If the unit is switched off or unplugged, you must allow at least 5 minutes before
restarting or re-plugged the unit in order not to damage the compressor.
• The freezer of the refrigerator can cool up to -12°C .
UK - 5 -
Accessories
“Door Open” Indicator;
• The « Door Open » indicator on the handle shows whether the door
has closed properly or whether it is still open.
• If the indicator is red, the door is still open.
• If the indicator is white, the door is properly closed.
• Observe that the freezer’s door should always be kept closed. This
will prevent food products from defrosting; it will avoid heavy ice and
frost build-up inside the freezer and an unnecessary increase in
energy consumption.
Making Ice cubes;
Ice tray ;
• Fill the ice tray with water and place in freezer compartment.
• After the water completely turned into ice, you can twist the tray as shown below to get
the ice cube.
(In some models)
UK - 6 -
Temperature indicator
In order to help you better set your refrigerator, we have
equipped it with a temperature indicator located in the coldest area.
To better store the food in your refrigerator, especially in
the coldest area, make sure the message “OK” appears
on the temperature indicator. If « OK » does not appear,
this means that the temperature setting has not been done
properly.
Since “OK” appears in black, it will be difficult to see this indication if the temperature
indicator is badly lit. To be able to see this indication properly, there should be enough
light.
Each time the temperature setting device is changed, wait for the stabilisation of the
temperature inside the appliance before proceeding, if necessary, with a new temperature setting. Please change the position of the temperature setting device progressively
and wait at least 12 hours before starting a new check and potential change.
NOTE: Following repeated openings (or prolonged opening) of the door or after putting
fresh food into the appliance, it is normal for the indication “OK” not to appear in the
temperature setting indicator. If there is an abnormal ice crystals build up (bottom wall of
the appliance) on the refrigerator compartment evaporator (overloaded appliance, high
room temperature, frequent door openings), put the temperature setting device on a
lower position until compressor off periods are obtained again.
Putting food in the coldest area of the refrigerator
Your foods will be better stored if you put them in the most
appropriate cooling area. The coldest area is just above the
crisper.
The following symbol indicates the coldest area of your refrigerator.
To be sure to have a low temperature in this area, make sure
the shelf is located at the level of this symbol, as shown in the
illustration.
UK - 7 -
The upper limit of the coldest area is indicated by the
lower side of the sticker (head of the arrow). The coldest
area upper shelf must be at the same level with the
arrow head. The coldest area is below this level.
As these shelves are removable, make sure they are
always at the same level with these zone limits
described on the stickers, in order to guarantee temperatures in this area.
Each type of food has an ideal conservation temperature and consequently a particular location to follow.
LocationsProducts
Upper shelves
Coldest area
CrisperFresh vegetables and fruits.
Door-liner
Cooked foods, desserts and all foods to be
eaten fast enough
Meat, poultry, game and raw fish
Maximum conservation time : 1 to 2 days.
Fresh fruits, cooked pork meat.
Door trays shall contain bottles at the
bottom side and, in their upper parts, low
volume and currently used products like
yoghurt, fresh cream, etc.
Butter, cooked cheese and eggs shall be
introduced in appropriate holders.
UK - 8 -
PART- 3.
• Disconnect unit from the power supply before cleaning.
• Do not clean the appliance by pouring water.
• The refrigerator compartment should be cleaned
periodically using a solution of bicarbonate of soda and
lukewarm water.
• Clean the accessories seperately with soap and water Do
not clean them in the washing machine.
• Do not use abrasive products, detergents or soaps.After
washing, rinse with clean water and dry carefully. When the
cleaning operations have been completed reconnect the
plug of the unit with dry hands.
• You should clean the condenser with broom at least twice
a year in order to provide energy saving and increase the
productivity.
CLEANING AND MAINTENANCE
Defrosting
For cooler compartment ;
• Defrosting occurs automatically in refrigerator compartment during operation ; the
defrost water is collected by the evaporating tray and evoparates automatically.
• The evaporating tray and the defrost water drain hole should be cleaned periodically
with defrost drain plug to prevent the water from collecting on the bottom of the
refrigerator instead of flowing out.
• You can also pour ½ glass of the water to drain hole to clean inside.
UK - 9 -
For freezer compartment;
The frost, accumulated in the freezer compartment, should be removed periodically. The
freezer compartment should be cleaned in the way as the refrigerator compartment, with
the defrost operations of the compartment at least twice a year.
For this;
• The day before you defrost, set the thermostat dial to 5. position to freeze the foods
completely.
• During defrosting, frozen foods should be wrapped in several layers of paper and
kept in a cool place. The inevitable rise in temperature will shorten their storage life.
Remember to use these foods within a relatively short period of time.
• Switch the refrigerator off at the socket outlet and pull the main plug
• Leave the door open and to accelerate the defrosting process one or more basins of
warm water can be placed in the freezer compartment.
• Dry the inside of the unit and water tray, refit the tray plug and set the thermostat knob
to 5 position.
Replacing The Light Bulb
When replacing the light of the refrigerator compartment;
1. Unplug the unit from the power supply,
2. Press the hooks on the sides of the light cover top and remove the light cover
3. Change the present light bulb with a new one of not more than 15 W.
4. Replace the light cover and after waiting 5 minutes plug the unit.
UK - 10 -
PART- 4.
TRANSPORTATION AND CHANGING OF
INSTALLATION POSITION
Transportation and Changing of Installation Position
• The original packages and foamed polystyrene (PS) can be concealed if required.
• In transportation the appliance should be tied with a wide stripe or a strong rope. The
rules written on the corrugated box must be applied while transporting.
• Before transporting or changing old installation position, all the moving objects
(ie,shelves,crisper…) should be taken out or fixed with bands in order to prevent the
shake.
Changing of Door Opening Direction
In case you need to change door-opening direction, please consult the domestic after
sales service.
(for some models)
PART- 5.BEFORE CALLING YOUR AFTER SALES SERVICE
If your refrigerator is not working properly,it may be a minor problem, therefore check the
following, before calling an electrician to save time and money.
What to do if your refrigerator does not operate ;
Check that ;
• There is no power,
• The general switch in your home is not disconnected ,
• The thermostat setting is on « 0 » position,
• The socket is not sufficient. To check this, plug in another appliance that you know
which is working into the same socket.
What to do if your refrigerator performs poorly ;
Check that ;
• You have not overloaded the appliance ,
• The doors are closed perfectly ,
UK - 11 -
• There is no dust on the condenser ,
• There is enough place at the rear and side walls.
If there is noise ;
The cooling gas which circulates in the refrigerator circuit may make a slight noise(bubbling
sound) even when the compressor is not running. Do not worry this is quite normal. If
these sounds are different check that ;
• The appliance is well leveled ,
• Nothing is touching the rear ,
• The stuffs on the appliance are vibrating.
If there is water in the lower part of the refrigerator ;
Check that ;
The drain hole for defrost water is not clogged(Use defrost drain plug to clean the drain
hole)
If your fridge is not cooling enough;
Your fridge is designed to operate in the ambient temperature intervals stated in the
standards, according to the climate class stated in the information label. We do not
recommend operating your fridge out of stated temperatures value limits in terms of
cooling effectiveness.
Climate ClassAmbient Temperature (°C)
TBetween 16 and 43 (°C)
STBetween 16 and 38 (°C)
NBetween 16 and 32 (°C)
SNBetween 10 and 32 (°C)
Recommendations
• In order to increase space and improve the appearance,the « cooling section » of
refrigerators is positioned inside the back wall of the refrigerator compartment. When
the appliance is running, this wall is covered with frost or water drops,according to
weather the compressor is running or not. Do not worry. This is quite normal. The
appliance should be defrosted only if an excessively thick layer forms on the wall.
• If the appliance is not used for long time (for example during the summer holidays)set
te thermostat knob to « 0 » position. Defrost and clean the refrigerator leaving the
door open to prevent the formation of midew and smell.
UK - 12 -
5 6 7
8 9 10
PART- 6.
THE PARTS OF THE APPLIANCE AND THE
COMPARTMENTS
1
2
3
4
This presentation is only for information about the parts of the appliance.
Parts may vary according to the appliance model.
1) REFRIGERATOR SHELF
2) CRISPER COVER (SAFETY GLASS -In some models- )
3) CRISPER
4) LEVELING FEET
5) THERMOSTAT BOX
6) FREEZER COMPARTMENT
7) TOP TABLE
8) ICE TRAY
9) EGG SHELF
10) BOTTLE SHELF
UK - 13 -
52059424
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.