Contents
1. INSTRUCTIONS FOR SAFETY AND USE ____________________ 11
2. INSTRUCTIONS FOR DISPOSAL ___________________________ 13
3. INSTALLING THE DISPLAY UNIT ___________________________ 14
4. DESCRIPTION OF THE CONTROLS ________________________ 15
5. CLEANING _____________________________________________ 16
INSTRUCTIONS FOR THE INSTALLER: these are intended for the
qualified technician who must install the appliance, set it functioning
and carry out an inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice, a
description of the commands and the correct procedures for cleaning
and maintenance of the appliance.
10
Presentation
1. INSTRUCTIONS FOR SAFETY AND USE
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST
BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR
THE WHOLE WORKING LIFE OF THE APPLIANCE.
WE ADVISE YOU TO CAREFULLY READ THIS MANUAL AND ALL
THE INSTRUCTIONS THEREIN BEFORE USING IT. INSTALLATION
MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN
ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS
APPLIANCE IS INTENDED FOR PROFESSIONAL USE AND
CONFORMS TO THE EC DIRECTIVES CURRENTLY IN FORCE. THE
APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING
FUNCTIONS: HEATING FOOD; ALL OTHER USES ARE
CONSIDERED UNSUITABLE.
THE MANUFACTURER CANNOT BE HELD LIABLE FOR USE
OTHER THAN AS INDICATED.
DO NOT DISCARD PACKING IN THE HOME ENVIRONMENT.
SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM TO
THE NEAREST SELECTIVE WASTE COLLECTION CENTRE.
THE APPLIANCE MUST BE EARTHED IN COMPLIANCE WITH
ELECTRICAL SYSTEM SAFETY REGULATIONS.
WHEN CONNECTING TO THE ELECTRICITY SUPPLY USING PLUG
AND SOCKET, MAKE SURE THAT BOTH ARE COMPATIBLE AND
CONNECT THEM TO THE POWER SUPPLY CABLE IN
ACCORDANCE WITH THE REGULATIONS IN FORCE.
NEVER UNPLUG BY PULLING ON THE CABLE.
DO NOT OBSTRUCT VENTILATION OR HEAT DISPERSAL
OPENINGS.
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF
INSPECTION TEST OF THE APPLIANCE, FOLLOWING THE
INSTRUCTIONS PROVIDED FURTHER ON. SHOULD THE
APPLIANCE NOT WORK, DISCONNECT IT FROM THE SUPPLY AND
CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE. NEVER
ATTEMPT TO REPAIR THE APPLIANCE.
WHENEVER YOU FINISH USING IT, ALWAYS MAKE SURE THAT
THE SWITCH IS IN THE O (OFF) POSITION.
11
Presentation
NEVER INSERT INFLAMMABLE OBJECTS: THEY COULD BE
ACCIDENTALLY IGNITED AND CAUSE FIRES.
THE IDENTIFICATION PLATE BEARING THE TECHNICAL DATA,
SERIAL NUMBER AND BRAND NAME IS POSITIONED UNDER
THE APPLIANCE.
DO NOT REMOVE THIS PLATE FOR ANY REASON.
THE APPLIANCE IS DESIGNED FOR PROFESSIONAL USE BY
TRAINED PERSONS. KEEP CHILDREN AT A SAFE DISTANCE AND
NEVER ALLOW THEM TO PLAY WITH IT.
THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE
(INCLUDING CHILDREN) OF REDUCED PHYSICAL AND MENTAL
ABILITY, OR LACKING IN EXPERIENCE IN THE USE OF
ELECTRICAL APPLIANCES, UNLESS THEY ARE SUPERVISED OR
INSTRUCTED BY ADULTS OR PEOPLE RESPONSIBLE FOR THEIR
SAFETY.
THE APPLIANCE IS DESIGNED FOR A MAXIMUM LOAD OF 2 KG.
THIS APPLIANCE IS MARKED ACCORDING TO EUROPEAN DIRECTIVE
2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE).
THIS DIRECTIVE DEFINES THE STANDARDS FOR THE COLLECTION AND
RECYCLING OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
APPLICABLE THROUGHOUT THE EUROPEAN UNION.
BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL LABELS AND
PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.
The manufacturer declines all responsibility for damage to persons
or things caused by the non-observance of the above prescriptions or
deriving from tampering with any part of the appliance or by the use of
non-original spares.
12
Presentation
2. INSTRUCTIONS FOR DISPOSAL OUR ENVIRONMENTAL CARE
Our product's packing is made of non-polluting materials, therefore
compatible with the environment and recyclable. Please help by
disposing of the packing correctly. Find the addresses of collection,
recycling and disposal centres from your retailer or from the competent
local organisations.
Do not throw the packing or any part of it away. They can constitute a
suffocation hazard for children, especially the plastic bags.
Your old appliance also needs to be disposed of correctly.
Important: hand over your appliance to the local agency authorised for
the collection of electrical appliances no longer in use. Correct disposal
means intelligent recycling of valuable materials.
Before disposing of your old appliance remove the door and leave the
racks in their normal working positions so that children cannot get stuck
in the compartment whilst playing.
It is also necessary to cut the interconnecting cable to the power supply
network, removing it along with the plug.
INFORMATION FOR USERS
Pursuant to Directives 2002/95/EC, 2002/96/EC and 2003/108/EC
relating to the reduction of the use of hazardous substances in electrical
and electronic appliances, as well as to the disposal of refuse, the
crossed-out bin symbol on the appliance indicates that the product, at
the end of its useful life, must be collected separately from other refuse.
Therefore, the user must consign the product that has reached the end
of its working life to the appropriate differentiated collection centres for
electrical and electronic refuse, or deliver it back to the retailer when
purchasing an equivalent product, on a one for one basis. Adequate
selective collection for the subsequent forwarding of the
decommissioned product to recycling, treatment and ecologically
compatible disposal contributes to avoiding possible negative effects on
the environment and on health and promotes the recycling of the
materials of which the appliance consists. Illicit disposal of the product by
the user will result in the application of administrative sanctions.
13
Instructions for the installer
3. INSTALLING THE DISPLAY UNIT
The appliance must be installed on a free-standing horizontal work top.
The distance from the rear wall must allow easy access to the terminal
board for connection of the power supply cable. Installation must be
carried out by a qualified technician and in compliance with EC
DIRECTIVES currently in force.
3.1 Electrical connection
Make sure the voltage and the cross-section of the power supply line
match the specifications indicated on the identification plate positioned
underneath. Do not remove this plate for any reason.
The appliance is fitted with a H05RN-F three-core cable for operation at
230V∼ and a power supply plug.
The supplied cable is a H5RN-F 3 x 0.75 mm2 three-core cable.
The power supply cable must be replaced by the manufacturer or by an
authorised service centre to prevent any risks.
The terminal indicated by this symbol links up parts that are normally
earthed. Connect the appliances appropriately using this terminal in
order to make sure that they are equipotential.
The plug and wall-mounted socket must be of the same type (in
accordance with current regulations). Make sure that the supply line is
suitably earthed. Avoid use of adapters and shunts.
The manufacturer cannot be held liable for damage to persons or
things caused by failure to observe the above instructions or deriving
from tampering with any part of the appliance.
14
Instructions for the user
4. DESCRIPTION OF THE CONTROLS
THERMOSTAT KNOB
Allows you to select the most suitable heating
temperature.
The desired temperature is selected by turning the knob
clockwise. Adjustment is progressive so that the oven
also operates at any intermediate value.
ON / OFF BUTTON
Allows you to switch on the heating element inside the display
unit.
GREEN INDICATOR LIGHT
When on, it indicates that the appliance is heating up. When
the temperature set using the thermostat knob is reached, the
light goes off. During heating, the light comes on and goes off
various times signalling that the temperature is being kept
constant as per the set value.
IMPORTANT
When using the exhibitor for heating,
make sure that the sponge inside the
central tray is immersed in the water
in order to humidify the inside.
15
Instructions for the user
5. CLEANING
Important:
do not aim jets of water directly against the appliance; avoid the use of
pressure jets.
Before performing any operations, switch off the power supply.
5.1 Cleaning the Plexiglas parts
Use specific products for cleaning. It is not recommended to use alcohol.
5.2 Cleaning the stainless steel parts
To clean and preserve the stainless steel surfaces, always use only
specific products that do not contain abrasives or chlorine-based acids.
How to use: pour the product onto a damp cloth and wipe the surface,
rinse thoroughly and dry with a soft cloth or chamois leather.
Do not use metallic sponges or sharp scrapers: they will
damage the surface.
Use ordinary non-abrasive products for steel, with the aid of
wooden or plastic utensils if necessary.
Rinse thoroughly and dry with a soft cloth or chamois leather.
16
Loading...