Smeg DWF62WH.1,LS200B.1,LVF23B.1,LVF23B.2,PL200K,PLTW62-2,SDTW62-2,SNZ660X.1 Instruction Manual

INSTRUCTION MANUAL
DISHWASHER
Contents
25
1. Safety and operating instructions __________________________ 26
2. Installation and hook-up _________________________________ 28
2.2 Electrical connection ________________________________________________________ 29
3. Description of the controls _______________________________ 30
3.1 Front panel________________________________________________________________ 30
3.2 Washing programs__________________________________________________________ 33
4. Operating instructions___________________________________ 35
4.1 Using the water softening system ______________________________________________ 35
4.2 Using the rinse aid and detergent dispensers _____________________________________ 37
4.3 General warnings and recommendations ________________________________________ 39
4.4 Using the baskets___________________________________________________________ 40
5. Cleaning and maintenance _______________________________ 43
5.1 General warnings and recommendations ________________________________________ 43
Thank you for choosing this product. We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. The manual is divided into paragraphs, which provide a step by step description of the dishwasher functions, with clear instructions accompanied by detailed illustrations. Recommendations are given for the correct use of the baskets, spray arms, containers, filters, washing programs, and for operating the controls. Follow the recommended cleaning procedures to ensure that your dishwasher always remains in perfect working order. This manual provides a quick and easy reference for answering all your questions concerning the use of your new dishwasher.
INSTALLATION INSTRUCTIONS: these are intended for the
qualified technician
who must carry
out the installation, hook-up and testing of the appliance.
USER INSTRUCTIONS: these consist of recommendations for using the appliance, a description of its controls and of the correct cleaning and maintenance procedures.
Safety instructions
26
1. Safety and operating instructions
THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE, AND COMPLIES WITH THE
EEC DIRECTIVES 72/23, 89/336 (INCLUDING 92/31)
CURRENTLY IN FORCE, INCLUDING THE PREVENTION AND ELIMINATION OF RADIO FREQUENCY INTERFERENCE. THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE:
WAS HIN G AND DRYING OF DISHES
; ANY OTHER USE SHALL BE CONSIDERED
IMPROPER.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR USES OTHER THAN THOSE
DESCRIBED ABOVE.
THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL NUMBER AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE DOO R.
THE NAME PLATE ON THE INNER EDGE OF THE DOOR MUST NEVER BE
REMOVED.
DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS MATERIALS WHICH MAKE UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE.
THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO EARTH THE APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.
IF THE APPLIANCE IS NOT CONNECTED TO THE ELECTRICAL POWER SUPPLY BY MEANS OF A PLUG, IT IS NECESSARY TO INSTALL AN ISOLATION SWITCH WITH A CONTACT OPENING GAP OF AT LEAST 3 MM.
THE PLUG ON THE POWER CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE, AND MUST CONFORM TO THE REGULATIONS IN FORCE. CHECK THAT THE VOLTAGE AND FREQUENCY OF THE ELECTRICAL POWER SUPPLY MATCH THE RATINGS ON THE NAME PLATE. AVOID USING ADAPTORS OR SHUNT CONNE CT IONS.
NEVER UNPLUG THE APPLIANCE BY PULLING THE POWER CORD.
AFTER INSTALLATION, THE PLUG MUST REMAIN ACCESSIBLE.
IN THE EVENT OF DAMAGE TO THE POWER CORD, HAVE IT REPLACED BY A QUALIFIED TECHNICIAN.
IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR, ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT OBSTRUCTED.
ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO AVOID WASTING ELECTRICITY.
OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET, AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN (LOCKS, DOORS, ETC.). THE APPLIANCE MUST THEN BE TAKEN TO A SORTED WASTE COLLECTION CENTRE.
IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER FROM THE ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP. THEN CALL IN A QUALIFIED TECHNICIAN.
Safety instructions
27
DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRANSIT! IF IN DOUBT, CONSULT YOUR DEALER. THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY A QUALIFIED TECHNICIAN.
THE APP LIAN CE IS IN TE NDED FOR U SE BY ADULTS .
DO NOT ALLOW CHILDREN TO COME NEAR OR PLAY WITH THE DISHWASHER. KEEP CHILDREN AWAY FROM DETERGENTS AND FROM THE OPEN DISHWASHER DOOR. THE PACKAGING MATERIALS (PLASTIC BAGS, POLYSTYRENE, METAL BARS, ETC.) MUST NOT BE LEFT WITHIN THE REACH OF CHILDREN. KEEP CHILDREN AWAY FROM THE OPEN DISHWASHER. THE APPLIANCE MAY CONTAIN RESIDUES OF DETERGENT WHICH CAN CAUSE IRREVERSIBLE DAMAGE TO THE EYES, MOUTH, AND THROAT, AS WELL AS POSSIBLE DEATH BY SUFFOCATION.
DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH MAY CAUSE AN EXPLOSION.
DO NOT LOAD DISHES THAT ARE SOILED WITH ASH, WAX OR PAINTS.
LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY CAUSE THE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK.
DO NOT UNDER ANY CIRCUMSTANCES TOUCH THE HEATING ELEMENT IMMEDIATELY AFTER THE END OF A WASHING PROGRAM.
OVER TIME, THE DISHWASHER HEATING ELEMENTS MAY CHANGE COLOUR, IN PART OR OVERALL. THIS IS PERFECTLY NORMAL AND DOES NOT IN ANY WAY AFFECT THE OPERATION OF THE APPLIANCE.
DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE.
KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE­DOWN, OR LAID HORIZONTAL IN THE TOP BASKET. TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT THEY DO NOT PROJECT FROM THE BASKET.
AQUASTOP MODELS
THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A WATER LEAK. WHEN THE AQUASTOP DEVICE IS TRIPPED, CALL IN A QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT. IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE.
DO NOT CUT THE HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO WATER.
IN THE EVENT OF DAMAGE TO THE WATER INTAKE HOSE, DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY AND FROM THE WATER SUPPLY.
IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW. IF THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE.
THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN:
REPAIRS CARRIED OUT BY UNAUTHORISED PERSONS WILL
INVALIDATE THE WARRANTY, AS WELL AS POSING A POTENTIAL HAZARD TO THE USER.
The manufacturer declines all responsibility
for damage to persons or property resulting from failure to observe the above precautions, from tampering with even a single component of the appliance, or from the use of non original spare parts.
Installation instructions
28
2. Installation and hook-up
Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. To ensure stability, install integrated or built-under dishwashers only under continuous worktops, and screw them to the adjacent units. To facilitate the installation procedure, the intake and drain hoses can be positioned in any direction; make sure that the hoses are not kinked, crushed or pulled too tightly. A hole at least 8 cm in diameter is required to allow the power supply cable and pipes to pass.
Level the appliance on the floor using its adjustable feet. This operation is essential for ensuring correct operation of the dishwasher.
For free-standing models only:
if the appliance is not built-in and is therefore accessible on one side, the door hinge area must be covered for safety reasons (injury hazard). The covering fixtures are available as an accessory from specialist dealers or the After-Sales Service.
Some models are equipped with only one adjustable foot at the rear, which can be adjusted by turning the screw on the lower front part of the appliance.
2.1 Water supply connection
Preventing the risk of clogging or damage:
if the water pipe is new or has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance.
The dishwasher must always be connected to the water system with new hoses; old or used ho se s must ne ver be reused.
CONNECTING TO THE WATER SUPPL Y
Connect the intake hose to a cold water supply with ¾” gas thread, inserting the filter A supplied with the dishwasher.
Take care to screw the hose firmly into place with your hands and then complete by tightening about ¼ of a turn with pliers. In dishwashers equipped with the ACQUASTOP device, the filters is already fitted inside the threaded ring.
Installation instructions
29
The dishwasher can also be connected to a hot water supply
not exceeding 60°C
. Supplying the appliance with hot water cuts down the washing time by approximately 20 minutes, but slightly reduces its effectiveness. Make the connection to the domestic hot water supply using the same procedure described for connecting to the cold water supply.
DRAIN CONNECTION
Insert the dishwasher’s drain hose into a drain pipe having a diameter of at least
4 cm
, or alternatively, place it inside the kitchen sink using the plastic support provided, taking care not to crush or excessively bend the hose. It is important to prevent the hose from coming loose and falling. For this purpose, the plastic support is equipped with a hole for tying it to the wall or water tap. The free end should be positioned at a height of between
30 and 100 cm,
and should never be submerged in water. If a hor i zo nt al d rain exte nsio n hose is used (for a maximum of 3 m) the drain hose can be placed at a maximum height of
85 cm
from the ground.
2.2 Electrical connection
Plug the power cord into a suitable electrical outlet, according to the instructions given in chapter "1. Safety and operating instructions".
User instructions
30
3. Description of the controls
3.1 Front panel
All the dishwasher controls are grouped on the front panel, which is of different shape depending on the model.
1
WASHING PROGRAM
SELECTOR
2
SELECTED PROGRAM
INDICATOR DISC (certain models only)
3
ON/OFF
BUTTON
4
ECO (45°C-55°C) PROGRAM
BUTTON (depending on models)
5
POWER ON
LIGHT
6
SALT
WARNING LIGHT (certain models only)
7
RINSE AID
WARNING LIGHT (certain models only)
8
RECESSED DOOR HANDLE
SETTING THE WASHING PROGRAM
To select the most suitable washing program, refer to the table below which indicates the recommended washing according to dish type and the degree of soiling.
After using the table to identify the most appropriate washing program, turn the
PROGRAM
SELECTION
knob
(1)
to set the program of choice by aligning the pointer with the program number. If the applia nce is fitted with the selected program indicator disc, this will show the number of the program set.
User instructions
31
TABLE OF PROGRAMS 45°C (6 program models)
AMOUNT OF DETERGENT
PROGRAM SEQUENC E DURATION CONSUMPTION
CYCLE SWITCH BUTTON
TYPE A ND DEGREE
OF DI RT O N DIS HES
GRAMS PREWASH WASH COLD RINS E HOT RINSE DRYING MINUTES
(2)
WATER
LITRES (1)
POWER KWh (2)
SOAK
1
_
PANS AND DISHES PENDING COMPLETI ON OF THE L OAD
_
COLD
_ _ _ _
6' 4
_
INTEN SIVE
65°C
2
_
VERY DIRTY P ANS AND DISHES, EVEN WITH DRIED-ON DIRT
30
COLD
65°C 2 65°C YE S 90' 22 1,55
NORMAL
60°C
3
_
PANS AND DISHES WITH NORMAL DIRT
30
COLD
60°C 1 65°C YE S 80' 18 1,40
NORMAL
45°C
(*) EN50242
3
ECO
DISHES WITH NORMAL DIRT
30
COLD
45°C 1 65°C YE S 76' 18 1,24
ECON OMY
45°C
4
ECO
DISHES WITH LIGHT DIRT
30
_
45°C 1 65°C YE S 70' 14 1,20
RINSE
5
_
DISHES FOR RINSING AND DRYING
_ _ _
1 65°C YE S 45' 9 0,8
TABLE OF PROGRAMS 55°C (6 program models)
AMOUNT OF DETERGENT
PROGRAM SEQUENC E DURATION CONSUMPTION
CYCLE SWITCH BUTTON
TYPE A ND DEGREE
OF DI RT O N DIS HES
GRAMS PREWASH WASH COLD RINS E HOT RINSE DRYING MINUTES
(2)
WATER
LITRES (1)
POWER KWh (2)
SOAK
1
_
PANS AND DISHES PENDING COMPLETI ON OF THE L OAD
_
COLD
_ _ _ _
6' 4
_
INTEN SIVE
65°C
2
_
VERY DIRTY P ANS AND DISHES, EVEN WITH DRIED-ON DIRT
30
COLD
65°C 2 65°C YE S 90' 22 1,55
NORMAL
60°C
3
_
PANS AND DISHES WITH NORMAL DIRT
30
COLD
60°C 1 65°C YE S 80' 18 1,40
NORMAL
55°C
(*) EN50242
3
ECO
DISHES WITH NORMAL DIRT
30
COLD
55°C 1 65°C YE S 76' 18 1,24
ECON OMY
55°C
4
ECO
DISHES WITH LIGHT DIRT
30
_
55°C 1 65°C YE S 70' 14 1,20
RINSE
5
_
DISHES FOR RINSING AND DRYING
_ _ _
1 65°C YE S 45' 9 0,8
Only
run the soak program with half loads. (*) EN 50242 reference program, for Class "C" energy efficient devices. (**) EN 50242 reference program, for Class "B" energy efficient devices.
(–) Not present. (1) Average power consumption with the softener set on
level 2
.
(2) The cycle duration and power consumption may vary according to the water and room temperatures, and the type and amount of dishes.
Loading...
+ 18 hidden pages