Smeg DWD1E User Manual

INSTRUCTION MANUAL

DISHWASHER

Contents

1. Safety and operating instructions ___________________________ 28

2. Installation and hook-up __________________________________ 30

2.1 Water supply connection _____________________________________________________ 30

2.2 Electrical connection ________________________________________________________ 31

3. Description of the controls_________________________________ 32

3.1 Front panel ________________________________________________________________ 32

3.2 Information display __________________________________________________________ 32

3.3 Washing programs __________________________________________________________ 35

4. Operating instructions ____________________________________ 38

4.1 Using the water softening system ______________________________________________ 38

4.2 Using the rinse aid and detergent dispensers _____________________________________ 40

4.3 General warnings and recommendations ________________________________________ 42

4.4 Using the baskets___________________________________________________________ 43

5. Cleaning and maintenance ________________________________ 46

5.1 General warnings and recommendations ________________________________________ 46

6. Troubleshooting ________________________________________ 49

Thank you for choosing this product. We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. The manual is divided into paragraphs, which provide a step by step description of the dishwasher functions, with clear instructions accompanied by detailed illustrations. Recommendations are given for the correct use of the baskets, spray arms, containers, filters, washing programs, and for operating the controls. Follow the recommended cleaning procedures to ensure that your dishwasher always remains in perfect working order. This manual provides a quick and easy reference for answering all your questions concerning the use of your new dishwasher.

INSTALLATION INSTRUCTIONS: these are intended for the out the installation, hook-up and testing of the appliance.

qualified technician

who must carry

USER INSTRUCTIONS: these consist of recommendations for using the appliance, a description of its controls and of the correct cleaning and maintenance procedures.

Safety instructions

1. Safety and operating instructions

THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE, AND COMPLIES WITH THE PREVENTION AND ELIMINATION OF RADIO FREQUENCY INTERFERENCE. THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE: IMPROPER.

DESCRIBED ABOVE.

THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL NUMBER AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE DOOR.

REMOVED.

DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS MATERIALS WHICH MAKE UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR USES OTHER THAN THOSE

EEC DIRECTIVES 72/23, 897336 (INCLUDING 92/31)

WASHING AND DRYING OF DISHES

THE NAME PLATE ON THE INNER EDGE OF THE DOOR MUST NEVER BE

CURRENTLY IN FORCE, INCLUDING THE

; ANY OTHER USE SHALL BE CONSIDERED

THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO EARTH THE APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.

IF THE APPLIANCE IS NOT CONNECTED TO THE ELECTRICAL POWER SUPPLY BY MEANS OF A PLUG, IT IS NECESSARY TO INSTALL AN ISOLATION SWITCH WITH A CONTACT OPENING GAP OF AT LEAST 3 MM.

THE PLUG ON THE POWER CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE, AND MUST CONFORM TO THE REGULATIONS IN FORCE. CHECK THAT THE VOLTAGE AND FREQUENCY OF THE ELECTRICAL POWER SUPPLY MATCH THE RATINGS ON THE NAME PLATE. AVOID USING ADAPTORS OR SHUNT CONNECTIONS.

NEVER UNPLUG THE APPLIANCE BY PULLING THE POWER CORD.

• AFTER INSTALLATION, THE PLUG MUST REMAIN ACCESSIBLE.

• IN THE EVENT OF DAMAGE TO THE POWER CORD, HAVE IT REPLACED BY A QUALIFIED TECHNICIAN.

IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR, ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT OBSTRUCTED.

ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO AVOID WASTING ELECTRICITY.

OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET, AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN (LOCKS, DOORS, ETC.). THE APPLIANCE MUST THEN BE TAKEN TO A SORTED WASTE COLLECTION CENTRE.

IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER FROM THE ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP. THEN CALL IN A QUALIFIED TECHNICIAN.

Safety instructions

DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRANSIT! IF IN DOUBT, CONSULT YOUR DEALER. THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY A QUALIFIED TECHNICIAN.

THE APPLIANCE IS INTENDED FOR USE BY ADULTS.

THE DISHWASHER. KEEP CHILDREN AWAY FROM DETERGENTS AND FROM THE OPEN DISHWASHER DOOR. THE PACKAGING MATERIALS (PLASTIC BAGS, POLYSTYRENE, METAL BARS, ETC.) MUST NOT BE LEFT WITHIN THE REACH OF CHILDREN. KEEP CHILDREN AWAY FROM THE OPEN DISHWASHER. THE APPLIANCE MAY CONTAIN RESIDUES OF DETERGENT WHICH CAN CAUSE IRREVERSIBLE DAMAGE TO THE EYES, MOUTH, AND THROAT, AS WELL AS POSSIBLE DEATH BY SUFFOCATION.

DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH MAY CAUSE AN EXPLOSION.

DO NOT LOAD DISHES THAT ARE SOILED WITH ASH, WAX OR PAINTS.

LEARNING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY CAUSE THE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK.

DO NOT UNDER ANY CIRCUMSTANCES TOUCH THE HEATING ELEMENT IMMEDIATELY AFTER THE END OF A WASHING PROGRAM.

OVER TIME, THE DISHWASHER HEATING ELEMENTS MAY CHANGE COLOUR, IN PART OR OVERALL. THIS IS PERFECTLY NORMAL AND DOES NOT IN ANY WAY AFFECT THE OPERATION OF THE APPLIANCE.

DO NOT ALLOW CHILDREN TO COME NEAR OR PLAY WITH

DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE.

AQUASTOP M ODE LS

THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A WATER LEAK. WHEN THE AQUASTOP DEVICE IS TRIPPED, CALL IN A QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT. IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE.

DO NOT CUT THE HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO WATER.

EVENT OF DAMAGE TO THE WATER INTAKE HOSE, DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY AND FROM THE WATER SUPPLY.

IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW. IF THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE.

DO NOT ATTEMPT TO REPAIR THE APPLIANCE.

THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN:

INVALIDATE THE WARRANTY, AS WELL AS POSING A POTENTI AL HAZARD TO THE USER.

The manufacturer declines all responsibility

REPAIRS CARRIED OUT BY UNAUTHORISED PERSONS WILL

for damage to persons or property resulting from failure to

IN THE

observe the above precautions, from tampering with even a single component of the appliance, or from the use of non original spare parts.

Installation instructions

2. Installation and hook-up

Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. To ensure stability, install integrated or built-under dishwashers only under continuous worktops, and screw them to the adjacent units. To facilitate the installation procedure, the intake and drain hoses can be positioned in any direction; make sure that the hoses are not kinked, crushed or pulled too tightly.

Level the appliance on the floor using its adjustable feet. This operation is essential for ensuring correct operation of the dishwasher.

Some models are equipped with only one adjustable foot at the rear, which can be adjusted by turning the screw on the lower front part of the appliance.

2.1 Water supply connection

Preventing the risk of clogging or damage:

long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance. The dishwasher must always be connected to the water system with new hoses; old or used hoses must never be reused.

CONNECTING TO THE WATER SUPPLY

Connect the intake hose to a cold water supply with 3/4” gas thread, inserting the filter A supplied with the dishwasher.

Take care to screw the hose firmly into place with your hands and then complete by tightening about 1/4 of a turn with pliers. In dishwashers equipped with the ACQUASTOP device, the filters is already fitted inside the threaded ring.

if the water pipe is new or has not been used for a

The dishwasher can also be connected to a hot water supply appliance with hot water cuts down the washing time by approximately 20 minutes, but slightly reduces its effectiveness. Make the connection to the domestic hot water supply using the same procedure described for connecting to the cold water supply.

not exceeding 60°C

. Supplying the

Installation instructions

DRAIN CONNECTION

Insert the dishwasher’s drain hose into a drain pipe having a diameter of at least place it inside the kitchen sink using the plastic support provided, taking care not to crush or excessively bend the hose. It is important to prevent the hose from coming loose and falling. For this purpose, the plastic support is equipped with a hole for tying it to the wall or water tap. The free end should be positioned at a height of between submerged in water. If a horizontal drain extension hose is used (for a maximum of 3 m) the drain hose can be placed at a maximum height of

30 and 100 cm

85 cm

4 cm

, or alternatively,

, and should never be

from the ground.

2.2 Electrical connection

Plug the power cord into a suitable electrical outlet, according to the instructions given in chapter "1. Safety and operating instructions".

User instructions

3. Description of the controls

3.1 Front panel

All the dishwasher's controls and indicators are located on the front panel, with layout varying depending on the models. Check whether your panel is Type "A" or "B" and then identify the control and monitoring devices in the key below.

YPE

"A"T

1 WASHING PROGRAM

2 ON/OFF

3 ON/OFF

4 POWER ON

5 START/STOP

6 ½ LOAD WASH

7 ECO DRYING CYCLE

8 INFORMATION DISPLAY

9 ½ LOAD WASH

10 ECO DRYING CYCLE

11 SALT

12 RINSE AID

13 DELAYED START

WARNING LIGHT

RECESSED DOOR HANDLE

DELAYED START

AND

BUTTON

LIGHT

BUTTON

LIGHT

WARNING LIGHT

SELECTOR

LIGHT

SELECTOR

BUTTON (certain models only)

YPE

"B"

3.2 Information display

The dishwasher is equipped with a practical the programmed dishwasher functions.

SETTING THE WASHING PROGRAM

To select the most suitable washing program, refer to the table below which indicates the recommended washing according to dish type and the degree of soiling.

Once the most suitable washing program has been selected using the table provided, turn the

WASHING PROGRAM SELECTOR (1)

to set the program required, placing it against the

identification symbol or nummer.

DISPLAY

which provides information on

User instructions

PROGRAM

SUPER

ECO

(*) BIO

EN 50242

(3)

EVERYDAY

NORMAL

PROGRAM SELECTOR

ECO

DRYING

(OPTIONAL)

INFORMATION

DISPLAY

DISHE TYPE

AND DEGREE

OF SOILING

HEAVILY SOILED

DISHES, POTS

AND PANS

WITH DRIED-ON

RESIDUE

NORMALLY

SOILED DISHES,

POTS AND PANS

WITH DRIED-ON

RESIDUE

SLIGHTLY SOILED

DISHES, POTS

AND PANS

WITH DRIED-ON

RESIDUE

NORMALLY SOILED DISHES, POTS AND PANS

WITHOUT DRIED-

ON RESIDUE

NORMALLY SOILED DISHES, POTS AND PANS

QUANT ITY

DETERGENT

10 - 25

PROGR AM SEQUE NCE DURATION CONSUMPTION

PRE-WASH WASH COLD

HOT

COLD

70°C 2 YES YES 135' 17 1,45

55°C 1 YES YES 118' 11 1,15

55°C 1 YES YES 160'

65°C 1 YES YES 100' 11 1,20

65°C 1 YES YES 104' 14 1,25

RINSE

HOT

RINSE

DRYING MINUTES

(2)

(3)

WATER

LITRES (1)

14 1,05

POWER Kwh (2)

(3)

QUICK

(4)

DELICATE

SOAK

(4)

Only

The

run the soak program with half loads.

HALF LOAD

SLIGHTLY

SOILED DELICATE

DISHES

SLIGHTLY

SOILED DISHES

DISHES, POTS

AND PANS

AWAITING COMPLETION OF THE LOAD

option

(6)

COLD

45°C 2

45°C 1 YES YES 78' 10 0,9

is available for all programs

NO 32' 10 0,4

NO 18' 4

except the soak program

(*) Reference program as EN 50242 standard.

(-) Not present.

(1) Average power consumption with the softener set on

level 2

(2) The cycle duration and power consumption may vary according to the water and room temperatures, and the type and amount of dishes.

(3) With

(4) For these programs, the

ECO DRYING

function selected.

ECO DRYING

function has no effect.

In programs containing the

symbol,

the ECO drying cycle option

is available. This activates the ventilation system which allows the dishes to be dried at lower temperatures (energy saving). With this option active, the program times are longer (about

20’

about

If the dishwasher door is left open or is not properly closed, the

for all the other cycles).

INFORMATION DISPLAY (8)

50’

for the

BIO P6

program;

will

signal that the washing program cannot be started.

User instructions

POWER SWITCH-ON (T

YPE

"A")

In order to switch on the appliance just turn the

POWER SWITCH-ON (T

To switch on the dishwasher press the

YPE

"B")

ON/OFF

will come on.

YPE

"A"T

ON/OFF

button

selector

(3)

(2)

till it corresponds with the letter

to start the program. The

YPE

"B"

PILOT

light

(4)

TABLE FOR CERTIFICATION BODIES

Reference standard EN 50242

Reference program

(*) Selector on P6 +

ECO DRYING

Load 12 place-settings Type of detergent B Amount of detergent 30 g Rinse aid setting Depending on the model 3/4 or 4/6

EN 50242

DISABLING THE END OF CYCLE ACOUSTIC DEVICE

It is possible to disable the sounding of the start/end of cycle acoustic device. Proceed as follows:

• press down the

INFORMATION DISPLAY (8)

• press the

HALF LOAD (6)

button for a few seconds until the symbol bSappears on the

;

button again to disable the acoustic device (the symbol bN appears

on the display);

•

press the

START/STOP (5)

button twice to exit the set-up mode.

+ 19 hidden pages