Smeg DWAU6D15XT3 User Manual
Contents
1. Safety and operating instructions __________________________ 2
2. Installation and hook-up _________________________________ 7
3. Description of the controls ______________________________ 11
4. Operating instructions __________________________________ 21
5. Cleaning and maintenance ______________________________ 40
6. Troubleshooting ______________________________________ 46
Thank you for choosing one of our products.
You are advised to read this manual carefully; it contains all the
information you need about the right conditions for the proper, safe use of
your dishwasher.
The individual sections are laid out to provide you with a step-by-step
guide to all your appliance's functions; the texts are easy to understand
and are complete with detailed illustrations.
Recommendations are given for the correct use of the baskets, spray
arms, containers, filters, washing programs, and for operating the controls.
Following the cleaning instructions provided here will keep your
dishwasher's performance at peak levels in the long term.
This user-friendly manual will provide answers to all your questions about
use of the dishwasher.
INSTALLATION INSTRUCTIONS: these are intended for the qualified
technician who must carry out the installation, hook-up and testing of the
appliance.
USER INSTRUCTIONS: these consist of recommendations for using the
appliance, a description of its controls and of the correct cleaning and
maintenance procedures.
1
MANUAL ALWAYS ACCOMPANIES THE APPLIANCE.
RESIDENTIAL FACILITIES.
PLACES (FOR EXAMPLE ON SHIPS, MOTOR CARAVANS, CARAVANS…….).
DESCRIBED ABOVE.
COMPLIANCE WITH THE REGULATIONS IN FORCE.
COLLECTION CENTRE.
APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.
User instructions
1. Safety and operating instructions
THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE; IT MUST
ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER FOR FUTIRE
REFERENCE. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE
INSTRUCTIONS CONTAINED IN THIS MANUAL. THEY CONTAIN IMPORTANT
INFORMATION FOR THE INSTALLATION, USE AND MAINTENANCE OF THE
APPLIANCE. IN THE EVENT OF SALE OR TRANSFER, ENSURE THAT THE
THIS APPLIANCE IS INTENDED FOR INDOOR USE IN A HOUSEHOLD
THIS APPLIANCE MUST NOT BE INSTALLED AND USED IN NON-STATIONARY
THIS APPLIANCE COMPLIES WITH DIRECTIVES 2006/95/EC AND
ENVIRONMENT AND SIMILAR SUCH AS STAFF KITCHENS OF SHOPS,
OFFICES AND OTHER WORKPLACES, INSTITUTIONS, AND FOR THE USE BY
GUESTS AT HOTELS, HOSTELS, BED AND BREAKFAST AND OTHER
2004/108/EC CURRENTLY IN FORCE, INCLUDING THE PREVENTION AND
ELIMINATION OF RADIO FREQUENCY INTERFERENCE AND IS DESIGNED
FOR THE FOLLOWING PURPOSE: WASHING AND DRYING OF DISHES; ANY
OTHER USE SHALL BE CONSIDERED IMPROPER. THE MANUFACTURER
DECLINES ALL RESPONSIBILITY FOR USES OTHER THAN THOSE
DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRANSIT!
IF IN DOUBT, CONSULT YOUR DEALER.
THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE
WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER.
INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN
DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED
WITHIN THE HOME. DO NOT ALLOW CHILDREN TO PLAY WITH PACKAGING
MATERIALS. SEPARATE THE VARIOUS MATERIALS WHICH MAKE UP THE
PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE
THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL NUMBER AND
MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE DOOR.
THE NAME PLATE MUST NEVER BE REMOVED.
THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN
ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO
PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO EARTH THE
2
FROM THE NETWORK..
DO NOT INSTALL THE APPLIANCE IN A PLACE SUBJECT TO FREEZING.
THEY MAY CAUSE DAMAGE.
OR BELOW IT.
FORBIDDEN.
AND THE CABINET, MUST BE ADEQUATELY FIXED.
AN ACCESSORY FROM SPECIALIST DEALERS OR THE AFTER
-
SALES.
THE RATINGS ON THE NAME PLATE OF THE APPLIANCE.
THE POSSIBILITY OF OVERHEATING OR BURNING.
NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER CORD.
POSITION ON THE SUPPLY LINE.
User instructions
DURING THE INSTALLATION THE APPLIANCE MUST BE DISCONNECTED
IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR,
ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT OBSTRUCTED.
DO NOT INSTALL THE APPLIANCE NEAR EQUIPMENT WITH HIGH
IRRADIATION TEMPERATURES (EG. GAS BURNERS, FIREPLACES, ETC.) AS
IF THE APPLIANCE IS INSTALLED IN A COMPARTMENT ABOVE OR BELOW
ANOTHER EQUIPMENT (EG. GAS BURNERS, OVENS, ETC.), READ
CAREFULLY THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OF
THE EQUIPMENT. IF THE INSTRUCTIONS OF THE EQUIPMENT DO NOT
CONTAIN INFORMATION, CONTACT THE MANUFACTURER OF THE
EQUIPMENT TO ENSURE THAT THE APPLIANCE CAN BE INSTALLED ABOVE
BUILDING-IN THE APPLIANCE UNDERNEATH A HOB IS ABSOLUTELY
FORBIDDEN.
INSTALL A HOB ON TOP OF A FREE-STANDING APPLIANCE IS ABSOLUTELY
TO ENSURE STABILITY, INSTALL THE APPLIANCE ONLY UNDER
CONTINUOUS WORKTOP, SECURELY FIXED TO ADJACENT CABINETS. IF
THE APPLIANCE IS INSTALLED IN A HIGH CABINET BOTH, THE APPLIANCE
IF THE APPLIANCE IS NOT BUILT-IN AND IS THEREFORE ACCESSIBLE ON
ONE SIDE, THE DOOR HINGE AREA MUST BE COVERED FOR SAFETY
REASON (INJURY HAZARD). THE COVERING FIXTURES ARE AVAILABLE AS
CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH
THE PLUG ON THE SUPPLY CORD AND THE CORRESPONDING SOCKET
OUTLET MUST BE OF THE SAME TYPE AND MEET THE REGULATION IN
FORCE.
DO NOT USE ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID
THE PLUG OF THE APPLIANCE MUST BE ACCESSIBLE AFTER
INSTALLATION.
IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD, A
CIRCUIT BREAKER PROVIDING A FULL DISCONNECTION IN OVERVOLTAGE
PROTECTION CLASS III MUST BE INSTALLED IN AN EASILY ACCESSIBLE
3
HOSES; OLD HOSES MUST NEVER BE REUSED.
TO REPAIR THE APPLIANCE.
PERSON RESPONSIBLE FOR THEIR SAFETY.
DO NOT ALLOW CHILDREN TO PLAY
WITH THE APPLIANCE.
PACKAGING OF THESE PRODUCTS.
AFTER COMPLETION OF THE WASH CYCLE.
DO NOT LOAD DISHES
THAT ARE SOILED WITH ASH, WAX OR PAINT.
CAUSE THE APPLIANCE TO OVERTURN.
NOT PROJECT FROM THE BASKET.
User instructions
THE APPLIANCE MUST BE CONNECTED TO THE WATER SUPPLY BY NEW
IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK
TEST OF THE APPLIANCE. IF THE DISHWASHER FAILS TO OPERATE
CORRECTLY, DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY
AND CALL THE NEAREST TECHNICAL SERVICE CENTRE. DO NOT ATTEMPT
THIS DISHWASHER MUST BE USED BY ADULTS. USE OF THE APPLIANCE
BY CHILDREN AGED FROM EIGHT YEARS AND PERSONS WITH REDUCED
PHYSICAL, SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE
AND KNOWLEDGE IS ONLY PERMITTED UNDER THE SUPERVISION OF A
SOME DETERGENTS ARE STRONGLY ALKALINE. AVOID CONTACT WITH
THE SKIN AND EYES. DETERGENTS CAN BE EXTREMELY DANGEROUS IF
SWALLOWED. THEY CONTAIN SUBSTANCES CAPABLE OF CAUSING
PERMANENT DAMAGE TO THE MOUTH AND THROAT, AND EVEN LEADING
TO SUFFOCATION. OBSERVE ALL THE SAFETY INSTRUCTIONS ON THE
KEEP CHILDREN AWAY FROM THE DISHWASHER WHEN THE DOOR IS
OPEN. ALWAYS CHECK THAT THE DETERGENT RECEPTACLE IS EMPTY
DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE
THE DISHES OR APPLIANCE AT THE END OF THE WASHING PROGRAM.
DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE IN
THE APPLIANCE, AS THIS MAY CAUSE AN EXPLOSION.
NEVER LEAVE THE DISHWASHER DOOR OPEN; PEOPLE MIGHT TRIP OVER
IT.
LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY
KNIVES OR OTHER SHARP-ENDED COOKING TOOLS MUST BE PLACED IN
THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN THE TOP
BASKET. TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT THEY DO
4
WAR
RANTY, AS WELL AS POSING A POTENTIAL HAZARD TO THE USER.
THE
MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE.
WIRING
RESPONSIBLE FOR THEIR SAFETY.
DO NOT USE STEAM CLEANERS TO CLEAN THE DISHWASHER.
MAINS POWER SUPPLY
.
PHOTOBIOLOGICAL RISK IN NORMAL CONDITIONS OF USE.
User instructions
THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE
REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL
EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED
EXCLUSIVELY BY TRAINED AND AUTHORISED TECHNICIANS: REPAIRS
CARRIED OUT BY UNAUTHORISED PERSONS WILL INVALIDATE THE
IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER FROM THE
ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP.
IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY
SOME COMPONENTS ARE LIVE EVEN WITH THE ON/OFF BUTTON IN THE
OFF POSITION. BEFORE MAINTENANCE WORK ON THE APPLIANCE,
DISCONNECT THE PLUG OR TURN OFF THE MAINS SWITCH IN THE FIXED
CLEANING AND REGULAR MAINTENANCE OF THE APPLIANCE BY
CHILDREN IS ONLY PERMITTED UNDER THE SUPERVISION OF A PERSON
MODELS WITH “AQUASTOP” DEVICE
THE “AQUASTOP” DEVICE PREVENTS FLOODING IN THE EVENT OF A
WATER LEAK. WHEN THE “AQUASTOP” DEVICE IS TRIPPED, CALL IN A
QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT.
INSIDE THE “AQUASTOP” WATER INTAKE HOSE, THERE ARE ELECTRICAL
PARTS. DO NOT CUT THE HOSE AND DO NOT ALLOW THE “AQUASTOP”
DEVICE TO DROP INTO WATER. IN THE EVENT OF DAMAGE TO THE
“AQUASTOP” WATER INTAKE HOSE, DISCONNECT THE APPLIANCE FROM
THE ELECTRICAL SUPPLY AND FROM THE WATER SUPPLY.
WARNING:
THE DEVICE ONLY WORKS IF THE DISHWASHER IS CONNECTED TO THE
MODELS WITH INTERNAL LIGHTING
THE LIGHTING SYSTEM OF THE APPLIANCE BELONGS TO RISK GROUP 1
UNDER THE IEC/EN 62471 STANDARD. THIS MEANS THAT THERE IS NO
5
MATERIALS WHICH COMPOSED THE DEVICE.
TECHNICAL DATA
from 8
50 mm to 8
88 mm Capacity
15 Standard place settings
User instructions
IN ACCORDANCE TO ART. 26 OF THE LEGISLATIVE DECREE 14 MARCH
2014, NR. 49 “IMPLEMENTATION OF THE DIRECTIVE 2012/19/EU ON WASTE
OF ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)”.
THE SYMBOL OF A CROSSED OUT WHEELIE BIN ON THE DEVICE OR
PACKAGE SHOWS THAT THE PRODUCT MUST BE COLLECTED SEPARATE
FROM OTHER WASTE, AT THE END OF ITS SERVICE LIFE. THEREFORE, THE
USER HAS TO TAKE ANY EQUIPMENT THAT HAS REACHED THE END OF ITS
SERVICE LIFE TO LOCAL WASTE DISPOSAL CENTRES FOR ELECTRICAL
AND ELECTRONIC EQUIPMENT WASTE.
AS AN ALTERNATIVE TO THE IDEPENDENT MANAGEMENT, IT IS POSSIBLE
TO DELIVER THE EQUIPMENT WHICH HAS TO BE DISPOSED OF TO THE
DEALER, AT THE MOMENT OF PURCHASING A NEW EQUIVALENT DEVICE
AT THE ELECTRONIC EQUIPMENT DEALERS WITH A SALES AREA OF AT
LEAST OF 400 M2. ALSO, FOR DISUSED DEVICES WITH DIMENSIONS
INFERIOR TO 25 CM, FREE DELIVERY TO THE DEALERS IS POSSIBLE, WITH
NO PURCHASE OBLIGATION
A PROPER SEPARATE WASTE COLLECTION AND THE CONSEQUENT
HEADING OF THE DISUSED DEVICE TOWARDS ITS RECYCLING, TREATMENT
AND ENVIRONMENTALLY COMPATIBLE DISPOSAL, CONTRIBUTES IN
PREVENTING ANY POSSIBLE NEGATIVE EFFECTS ON ENVIRONMENT AND
HEALTH; ALSO, IT SUPPORTS THE REUSE AND/OR RECYCLE OF THE
OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE
MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET,
AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR
CHILDREN (LOCKS, DOORS, CABLES, HOSES, ETC.).
The manufacturer declines all responsibility for damage to persons or property
resulting from failure to observe the above precautions, from tampering with
even a single component of the appliance, or from the use of non original spare
parts.
Width
Depth measured flush with the
outer edge of the control panel
Height (depending on models)
Water supply pressure min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar)
Electrical characteristics See rating plate
6
597 599 mm
570 mm
from 818 mm to 888 mm
out by authorised staff.
User instructions
2. Installation and hook-up
Remove the polystyrene basket retainers.
Position the appliance in the desired place of installation. The back or
sides of the dishwasher may be placed up against walls or other furniture
units. If the dishwasher is installed near a heat source, fit the special
insulating panel to prevent overheating and malfunction of the appliance.
To ensure stability, install integrated or built-under dishwashers only under
continuous worktops, and screw them to the adjacent units. To facilitate
the installation procedure, the intake and drain hoses can be positioned in
any direction; make sure that the hoses are not kinked, crushed or pulled
too tightly. Make sure to tighten the locking ring-nut once the pipes have
been placed in the direction required. A hole at least 8 cm in diameter is
required to allow the power supply cable and pipes to pass. Before putting
the dishwasher into its definitive position, turn on the water tap and check
that there are no leaks from the tap connection, the dishwasher
connection or the hose.
Level the appliance on the floor using the appropriate Allen key to regulate
the adjustable feet. This operation is essential for ensuring correct
operation of the dishwasher.
Some models are equipped with only one adjustable foot at the rear, which
can be adjusted by turning the screw on the lower front part of the
appliance.
Building-in a dishwasher underneath a hob is absolutely forbidden.
Moreover, dishwashers may not be installed directly touching appliances
which are not conventional built-in kitchen appliances (e.g. fireplaces,
stoves, etc.).
When installing the dishwasher in a compartment next to one or more other
appliances, it is essential to comply with all the recommendations provided
by the appliance’s manufacturer (minimum distances, installation
procedures, etc.).
For free-standing models only:
- Installing a hob on top of a free-standing dishwasher is absolutely
forbidden.
- To build in the dishwasher, the special kit must be purchased from
authorised dealers or the After-Sales Service.
- The tops of free-standing dishwashers can be removed to allow them to
be installed underneath a worktop. This procedure must be carried
7
Connect the intake hose to a cold water supply with ¾” gas
Take care to screw the hose firmly into place with your
hands and then complete by tightening about ¼ of a
In dishwashers equipped with the ACQUASTOP device,
User instructions
2.1 Water supply connection
Preventing the risk of clogging or damage: if the water pipe is new or
has not been used for a long time, before connecting to the water supply
check that the water is clear and free of impurities, to prevent damage to
the appliance.
The dishwasher must always be connected to the water system with
new hoses; old or used hoses must never be reused.
CONNECTING TO THE WATER SUPPLY
thread, inserting the filter A supplied with the dishwasher.
turn with pliers.
the filters is already fitted inside the threaded ring.
The dishwasher can also be connected to a hot water supply not exceeding
60°C. Supplying the appliance with hot water cuts down the washing time
by approximately 20 minutes, but slightly reduces its effectiveness. Make
the connection to the domestic hot water supply using the same procedure
described for connecting to the cold water supply.
8
85 cm
User instructions
DRAIN CONNECTION
Insert the dishwasher’s drain hose
into a drain pipe having a diameter
of at least 4 cm, or alternatively,
place it inside the kitchen sink
using the plastic support provided,
taking care not to crush or
excessively bend the hose. It is
important to prevent the hose from
coming loose and falling. For this
purpose, the plastic support is
equipped with a hole for tying it to
the wall or water tap.
The free end should be positioned at a height of between 30 and 100 cm,
and should never be submerged in water. If a horizontal drain extension
hose is used (for a maximum of 3 m) the drain hose can be placed at a
maximum height of
from the ground.
Class of protection against moisture: IPX0
9
LEAD.
User instructions
2.2 Electrical connection and precautions
CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH
THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON
THE INNER EDGE OF THE DOOR.
10
THE PLUG ON THE SUPPLY CORD AND THE CORRESPONDING SOCKET
OUTLET MUST BE OF THE SAME TYPE AND MEET THE REGULATIONS IN
FORCE.
THE PLUG MUST BE ACCESSIBLE AFTER INSTALLATION.
NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY
AFTER CHANGING THE SUPPLY CORD, MAKE SURE THAT THE BRACKET
WHICH SECURES THE CORD IS FIXED SECURELY IN PLACE.
DO NOT USE ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID
THE POSSIBILITY OF OVERHEATING OR BURNING.
In the event of damage to the supply cord, have it replaced by the
manufacturer or an Authorized Technical Service Centre in order to
avoid any risk.
Some components are live even with the ON/OFF button in the OFF position.
Before maintenance work on the appliance, remove the plug or turn off the
power supply at the wall switch.
User instructions
3. Description of the controls
3.1 Front panel
All the dishwasher controls are grouped on the upper panel. Switching
on, programming, switching off etc. are only possible when the door is
open.
ON/OFF BUTTON
1
OPTION BUTTONS/LIGHTS
2
SELECTED PROGRAM BUTTONS/LIGHTS
3
START/PAUSE BUTTON
4
TOP DISPLAY (3 FIGURES)
5
SALT WARNING LIGHT
6
RINSE AID WARNING LIGHT
7
3.2 The front panel
The front panel includes the DISPLAY which provides all information
concerning the programmed functions.
FRONT DISPLAY
8
DOOR HANDLE
9
N.B.: symbols and styling are guideline and may vary depending on
the model or version of the dishwasher purchased.
11
01.05
1 h
E01
h.3
P0
12
User instructions
Information shown on top display
Example of screen and information provided
Estimated wash cycle duration and time remaining
Delayed start information
Error message CHECK
Softener setting
Program cancellation
Information shown on front display
End of cycle message End
Estimated wash cycle duration and
time remaining
01: 55
Delayed start information Start in "X" hours
Error message Error 01 ……11
Softener setting h.3
Language selected IT-EN-FR……..
Prewash
Program phase icons.
Wash
They indicate the program status when a
program is running
Rinse
Drying
The icon appears if the washing program is cancelled or if there
is an error.
It does not appear during the drainage phases that are normally
part of the washing program, if it is carried out correctly.
10 seconds.
User instructions
LANGUAGE SELECTION
1-Switch on the dishwasher
2-Select a wash program (not Special Programs)
3-Press and hold the “half load” button until the currently selected language
appears on the front display.
Press the button again to scroll through the available languages. When the
required language appears on the display, select it by simply waiting a few
seconds without selecting any other options (the name of the chosen
language appears on the display) or switch off the dishwasher by pressing
the on/off button.
N.B.:
- With the door open, the display switches off after about
10 seconds with no commands.
- With the door closed, if the dishwasher is programmed but the start
is not confirmed (cycle not confirmed, program interrupted, start
not confirmed…) the name smeg appears on the display after about
WASH PROGRAM SELECTION AND SWITCHING-ON
For selection of the most suitable program for the dishes to be washed,
refer to the table below, which specifies the recommended type of wash,
also considering the type of dishes and the degree of soiling.
13
IEC/DIN***
Dry
hygiene.
the end of the cycle
door
opened
15 cm
Only
PROGRAMME
NUMBER
& SYMBOL
1 EXPRESS
27’
2 AUTO
45°-65°
3 (*)
NORMAL ECO
LOAD CROCKERY AND
Quick wash cycle for
lightly soiled dishes,
washed immediately after
Wash cycle for normally
soiled mixed loads such
as dishes and pans, even
with dried-on residues.
Crockery and cutlery
normally soiled.
User instructions
PROGRAMS TABLE
CUTLERY
use.
PROGRAM
PROGRESS
Wash at 38°C
Rinse at 50°C
When the "AUTO" program is selected, the dishwasher
recognises the type of dirt and automatically adjusts the
Cold prewash
Wash at 50°C
Cold rinse
Rinse at 42°C
DURATION
MINUTES
(1)
27
CONSUMPTION
WATER
LITRES
6,5 0,70
washing parameters as appropriate.
Waiting for the
Australian tests lab data
POWER
KWh (1)
4 REGULAR
Wash cycle for normally
soiled mixed loads such
as dishes and pans, even
with dried-on residues.
Wash at 55°C
Cold rinse
Rinse at
55°C or 70°C (2)
Dry
140/
90 (2)
13,5 1,35
Intensive wash cycle
5 STERILISE
ideal for plates, pots,
pans, cutting boards,
feeding bottles. Ideal for
baby dishes or if there
are allergy sufferers in
the family in order to
achieve a higher level of
Hot prewash
Wash at 75°C
2 cold rinses
Rinse at
55°C or 70°C (2)
Dry
160/
130 (2)
15,5 1,60
* Reference program as per AS/NZS 2007.
During the comparative tests the dishwasher shall to be setted as follow:
- DRY ASSIST option DISABLED
- At
the
must be
about
.
run the soak program with partial loads.
(1) The cycle duration and power consumption may vary according to the water
and room temperatures, and the type and amount of dishes.
(2) DRY ASSIST option selected or not selected
DRY ASSIST is activated automatically if the selected program is compatible
with the option. It can be disabled by pressing the relative button.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
14
+
during the night.
dried in 60 minutes.
level of hygiene.
lights
User instructions
SPECIAL PROGRAMS (see relevant section for explanation of functioning modes)
PROGRAMME
NUMBER E
SYMBOL
6 SOAK
7 CRYSTAL
8 SILENT
+
+
LOAD CROCKERY AND
CUTLERY
Recommended for rinsing
dishes while waiting for
another wash cycle.
Wash cycle for delicate
items, such as wine glasses
and lightly soiled fine china.
Ideal when you require
dazzlingly clean glassware
Wash cycle suitable for
normally soiled dishes, even
with dried-on residues.
Ensures maximum noise
reduction and is therefore
ideal if you wish to run it
PROGRAM
PROGRESS
Cold prewash
Wash at 45°C
2 Cold rinses
Rinse at
55°C or 70°C (2)
Dry
Wash at 55°C
Cold rinse
Rinse at
55°C or 65°C (2)
Dry
DURATION
MINUTES
(1)
CONSUMPTION
WATER
LITRES
15 3,5 0,02
125/
75 (2)
10,5 1,15
270/
245 (2)
12,5 1,25
POWER
KWh (1)
9 FULL
EXPRESS 60’
+
Quick wash cycle for
normally soiled mixed loads
such as dishes and pans,
even with dried-on residues.
Dishes are washed and
Wash at 65°C
Cold rinse
Rinse at
55°C or 70°C (2)
Dry
110/
60 (2)
13 1,40
Intensive wash cycle ideal
10 STERILISE
+
for plates, pots, pans,
cutting boards, feeding
bottles. Ideal for baby dishes
or if there are allergy
sufferers in the family in
order to achieve a higher
Hot prewash
Wash at 70°C
2 cold rinses
Rinse at
55°C or 70°C (2)
Dry
190/
155 (3)
10 1,20
The STERILISE program terminate with an extra anti-bacteria rinse that ensures a
further reduction in the bacteria level. If the temperature falls during this stage of the
program (e.g. because the door is opened or due to a power blackout), the program
flash to warn that the anti-bacteria effect is not guaranteed.
(1) The cycle duration and power consumption may vary according to the water
and room temperatures, and the type and amount of dishes.
(2) DRY ASSIST option selected.
DRY ASSIST is automatically activated if the selected program is compatible with
the option. It can be disabled by pressing the relative button.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
15
Loading...