Smeg DD612S7 User Manual

INSTRUCTION MANUAL

GGUUIIDDEEFFOORRUUSSIINNGGTTHHEEDDIISSHHWWAASSHHEERRAANNDDTTHHEEWWAASSHHIINNGGPPRROOGGRRAAMMS

Contents

1. Description of the controls________________________________16

2. Troubleshooting _______________________________________26

Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher. The individual sections are laid out to provide you with a step-by-step guide to all your appliance's functions; the texts are easy to understand and are complete with detailed illustrations. This user-friendly manual will provide answers to all your questions about use of the dishwasher. For any other information about use and maintenance of the dishwasher, read the enclosed manual carefully.

USER INSTRUCTIONS: useful information is provided for the use of the washing programs and all the dishwasher's functions.

User instructions

1. Description of the controls

1.1 Front panel

All the dishwasher control are grouped on the front panel.

1 ON/OFF

2 SELECTION PROGRAMS

3 DELAY PROGRAM

½LOADWASH

"3/1" OPTION

5 START/PAUSE

6 POWER ON

7 PROGRAMS

8 DELAY PROGRAM

9 ½LOADWASH

10 PHASES/PROGRAM

11 NO SALT

12 NO RINSE AID

RECESSED DOOR HANDLE

BUTTON

BUTTON (on some models only)

BUTTON

LIGHT

LIGHTS

LIGHTS (on some models only)

LIGHT (on some models only)

LIGHTS

LIGHT (on some models only)

BUTTONS

(P1...P5)

User instructions

PROGRAM SELECTION TYPE AND GR ADE DIRT

PAN S AN D DI SHE S

SOAK

QUICK

ECO (*)

EN 50242

DAILY

IN WAITING OF

COMPLETING

THE LOAD

DISHES NOT MUCH DIRTY

AND WITH "FRESH DIRT"

WITHOUT RESIDUAL DRY

PANSAND DISHES

NOT VERY DIRTY BUT

WITH DRY RESIDUALS

PAN S AN D DI SHE S

WITH NORMAL DIRT,

WITHOUT DRY RESIDUAL

PROGRESS

PROGRAM

Cold prewash

Wash at 38°C Cold rinse Rinse at 58°C

Wash at 50°C Cold rinse Rinse at 66°C Dry

Wash at 65°C Cold rinse Rinse at 68°C Dry

DURATION CONSUMPTION

MINUTES

(2)

WATE R

LITRES (1)

POWER KWh ( 2)

15 6 0,03

45 13 0,80

180 ** **

85 13 1,25

Wash at 70°C

STRONG

PAN S AN D DI SHE S

VERY DIRTY

2 cold rinses Rinse at 70°C

95 17 1,45

Dry

Cold prewash

DELICATE

DISHES

NOT VERY DIRTY

Wash at 45°C Cold rinse Rinse at 68°C

75 17 1,05

Dry

Cold prewash

BIO

PANS AND DISHES DIRTY

AND WITH DRY RESIDUALS

Wash at 55°C Cold rinse Rinse at 69°C

120 14 1,20

Dry

Cold prewash

NORMAL

PANS AND DISHES DIRTY

AND WITH DRY RESIDUALS

Wash at 65°C Cold rinse Rinse at 68°C

90 17 1,30

Dry

Prewash at 45°C Wash at 70°C 2coldrinses Rinse at 70°C

110 20 1,60

SUPER

PAN S AN D DI SHE S

VERY DIRTY AND WITH

DRY RESIDUALS

Dry

Only run the soak program with half loads. The HALF LOAD - "3/1" option (4) is available for all programs except the soak program. (*) Reference program as per EN 50242 standard.

(**) See energy label.

(1) Average power consumption with the softener set on level 2. (2) The cycle duration and power consumption may vary according to the water and room

temperatures, and the type and amount of dishes.

User instructions

1.2 Washing programs

The dishwasher is equipped with a control panel, described in chapter "1. Description of the controls", from which it is possible to carry out all the power switch-on, switch-off and programming operations.

Before starting a washing program make sure that:

 The water supply tap is  The

 The baskets have been  The spray arms are able to

 Thedishwasherdooris

correct amount of detergent

dispenser

obstruction.

open.

has been added to the

correctly loaded.

rotate freely

securely closed

and without

LIGHTING

When the and the light

PHASES/PROGRAM

PROGRAMMING

In this model of dishwasher, all programming procedures can only be carried out with the door closed. As long as the door is open, the

PROGRAMS

off.

ON/OFF

(6)

lights

(1)

button

comes on. About

lights

(7)

and

is pressed, the dishwasher switches on

(10)

will come on.

PHASES/PROGRAM

2 seconds

(10)

lights

later, the

will remain

User instructions

SELECTION PROGRAM

The program selection is possible

(5)

(2)

for a few

through the relative buttons

When the button relating to the program required is pressed, the relative light will come on to confirm the operation.

START PROGRAM

To start the dishwasher, press the

START/PAUSE

button seconds, until the light of the first phase of the selected program starts to flash (confirmation beep). This phase, that updates itself during the cycle, is “indicative” since it is influenced by the washing conditions such as dishwasher type and quantity, entry temperature etc. For this reason it is normal to see the updating during a program (increment and decrease of minutes) specially in the passage from one phase to the other (for example, from washing to rinse).

As the program runs, the the current cycle status.

Prewash

Wash

Rinse

Dry

PHASES/PROGRAM

lights

(10)

will indicate

The light of the phase in progress will flash, while the lights of the previous and subsequent phases remain on.

N.B.

during execution of programs which

do not include a prewash, the first

PHASES/PROGRAM

light

(10)

will remain

off.

User instructions

END PROGRAM

When the program finishes, a buzzer sounds briefly and all the

(10)

flash.

PHASES/PROGRAM

lights

Press any of the flashins, and the dishwasher is now ready to perform a new cycle; opening and shutting the door or switching the appliance off and on has the same effect.

INTERRUPTION OF A PROGRAM

In order to interrupt a running program it is necessary:

 press the

goes out;

 keep the button pressed until the

come on (confirmation buzzer).

SELECTION PROGRAMS

START/PAUSE

button

buttons

(5)

, the light of the current phase

PHASES/PROGRAM

(2)

, stops the light

lights

(10)

TO CHANGE A PROGRAM

To change the running program it is necessary:

 to interrupt the running program (see “  select the new program;  to press again the

program.

START/PAUSE

NTERRUPTION OF A PROGRAM

button

(5)

to make start the new

”);

User instructions

ANNULLING A PROGRAM

To annul the program in progress, it must first be interrupted (see

“

NTERRUPTION OF A PROGRAM

In case that the door is opened during the operation, to the next door closing it is going to be necessary to start the program as shown in paragraph “ which it was interrupted.

In case that the tub temperature is higher than 50°C the program will start about 30 seconds later.

The washing cycle will not take place if the dishwasher door is left open or not properly closed.

HALF LOAD WASH FUNCTION (on some models only) (available in all programs except the soak program)

Pressing button only.

After selecting the program, proceed as follows:

 press the button

(the relative light comes on);

 press the button

wash status (the light goes out).

½LOAD

The

soak

N.B.:

TART PROGRAM

wash option can be selected in all programs

program.

selecting the

½ LOAD WASH (4)

½LOAD

”).

Now press buttonsP1+P2simultaneously and the first three program lights will come on.

”. The program will resume from the point in

selects washing on the top basket

½LOADWASH(4)

option changes the duration of the program.

once to select the top basket

again to return to full load

except the

It is possible to place a cutlery basket inside the basket selected for the

HALF-LOAD

WARNING: do not load dishes and cutlery into the non-selected basket, because the water spray will only reach the selected basket.

program; the other basket

must remain empty.

User instructions

"3/1" OPTION BUTTON (on some models only) (available in all programs except the soak program)

By pressing the button the relative light comes on. This option has been studied for the use of dishwashing powder or tablets with integrated substances in place of regenerating salt or rinse-aid known on the market as “3 in 1” or “triple action” products; in this case the dishwasher will use the product in an optimal way avoiding salt and rinse-aid consumption, which could already be found in the dishwasher.

Note:

When selecting the "

rinse-aid lights remain on, if their containers are empty.

DELAY PROGRAM (on some models only) (available in all programs except the soak program)

PROGRAM DELAY

The the washing program by3, the dishwasher to work at your preferred time of day.

(4)

you activate the "

3/1

" button, it is normal that the salt and

(3)

button

6 or 9 hours.

can be pressed to delay the start of

3/1

" option, confirmed when

This function allows you to set

After selecting the delay, start the program (see relative section). The appliance will prewash the dishes, after which the "program delay" set previously will come into effect (the light corresponding to

hours

flashes).

reset or change the delay

 press the

PHASES/PROGRAM

 press the

program delay” returns to zero (all the lights indicating the delay go out);

 press the

START/PAUSE

DELAY PROGRAM

START/PAUSE

once the program has started:

(10)

(5)

for a few seconds, until the

come on;

(3)

button

(5)

several times “until the

to start the new program.

button

lights

button

3, 6or9

User instructions

To set the delay once the program has started

If the program you wish to carry out is the same as the one already in progress:

 press the

PHASES/PROGRAM

 annul the program in progress (see relative section) and wait for the

cycletocometoanend;

 select the program again;  select the delay required;  press the

If the program you wish to carry out is different from the one already in progress:

 press the

PHASES/PROGRAM

 change the program;  select the delay required;  press the

dishwahser will pump out the water and restart with the delay set and the new program.

START/PAUSE

lights

START/PAUSE

lights

START/PAUSE

button

(10)

(5)

come on;

(5)

to start the new program.

(5)

come on;

(5)

to start the new program. The

, proceed as follows.

for a few seconds, until the

User instructions

TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT

 Always try to run the dishwasher  Do not wash the dishes in running water.  Use the washing program that is

load.

 Do not carry out any preliminary rinsing.  If available, connect the dishwasher to a hot water supply up to

60°C.

TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT

The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following:



separate

resistant to aggressive detergents and high temperatures;



do not pour

the more delicate items from dishes that are more

the detergent directly on the dishes.

fully loaded

most appropriate

for each type of

REMOVING THE DISHES

At the end of the washing program, wait at least removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is upper basket.

advisable

to unload the lower basket first, and then the

20 minutes

before

User instructions

ADJUSTING THE WATER SOFTENING SYSTEM

The dishwasher is equipped with an device for the user to adjust the water softening system according to the hardness of the water supply.

According to the machine model, the selector which acts on the adjustment may be located:  inside the plastic locking ring located on the

the dishwasher;

 inside the water softener, just below the cap.

Both allow for adjustment to5settings:

right-hand

side, inside

WATER HARDNESS TABLE

WATER HARDNESS

German Degrees (°dH) French Degrees (°dF)

0-4 0-7 Setting N. 1 NO SALT

5-15 8-25 Setting N. 1 16 - 23 26 - 40 Setting N. 2 24 - 31 41 - 60 Setting N. 3 32 - 47 61 - 80 Setting N. 4 48 - 58 81 - 100 Setting N. 5

SETTING

Contact your local water board for information on the hardness of your water supply.

User instructions

2. Troubleshooting

In case of a malfunction, the dishwasher will identify the program by switching on a combination of lights.

When an alrm is present, all the

PROGRAM PHASES/PROGRAM

the error code:

CODE PHASES LIGHTS DESCRIPTION

lights

(7)

come on, while the

(10)

lights

identify

The anti-flooding system (if installed) has been tripped.

The system which limits the water level inside the dishwasher (safety unit) has been tripped.

The appliance cannot heat the water.

Temperature sensor disconnected.

The appliance is not able to take in water.

The appliance is not able to pump out the water from the tank.

The appliance is not able to measure the amount of water loaded accurately (on models with turbine flow-regulator only).

Anomaly in the system which distributes water to the basket (where installed).

The maximum level of water for loading has been exceeded (on models with turbine flow-regulator only).

+ 28 hidden pages