e
PRECAUTIONS 9
General safety instructions 9
Declaration of conformity 10
Declaration art. 10.10 Directive 2014/53/EU 10
This user manual 10
How to read the user manual 10
USE 10
SmegConnect 10
Connectivity requirements 10
We advise you to read this manual carefully, which contains all the instructions for maintaining the
appliance’s aesthetic and functional qualities. For further information on the product: www.smeg.com
Apple, App Store and iOS are trademarks of Apple Inc.
Google Play Store and Android are trademarks of Google Inc.
Wi-Fi is a trademark of Wi-Fi Alliance.
Installation of the App 10
Creation of the account 10
Product registration 11
Connection to the device 11
Remote connection 12
Change Access Point credentials 12
Information on the connection 13
Deletion of the registration 13
Software updates 13
What to do if... 13
PRECAUTIONS
General safety instructions
• The use of the App requires the
availability of a WLAN (Wi-Fi)
network with dedicated Internet
router, for the connection
between appliance and mobile
device.
• In case of poor signal for the
use of the appliance, envisage
to install a Wi-Fi repeater
nearby.
• Outside the coverage range of
the Wi-Fi network, the use of
the App involves the availability
of a data link for the mobile
device. CAUTION: additional
costs might arise depending on
the contract with the mobile
phone operator.
• The appliance can operate offline as a "non-connected"
household appliance, but it
cannot be controlled through
the App when the Wi-Fi
connection or the data link are
deactivated.
• In compliance with the
provisions regarding
electromagnetic compatibility,
the appliance belongs to group
2 and class B (EN 55011).
• This appliance complies with
the current standards and
directives regarding safety and
electromagnetic compatibility.
It is however recommended for
pacemaker wearers to
maintain a minimum distance of
20-30 cm between the
appliance when it is operating
and the pacemaker. Consult
the pacemaker manufacturer
for more information.
• In some models only, for safety
PRECAUTIONS - 9914779624/A
reasons and in compliance with
current legislation, some
functions cannot be activated
remotely.
Declaration of conformity
The manufacturer, SMEG, declares that the
types of radio equipment:
CVI118RWS2 - CVI118LWS2
CVI118RWN2 - CVI118LWN2
CVI318RWX2 - CVI318LWX2
CVI618RWNR2 - CVI618LWNR2
CVI618RWNX2 - CVI618LWNX2
CVI638RWN2 - CVI638LWN2
CVI338RWX2 - CVI338LWX2
CVI138RWS2 - CVI138LWS2
CVI621LWNR3 - CVI621RWNR3
CVI621LWNX3 - CVI621RWNX3
CVI638LWN3 - CVI638RWN3
comply with the directive 2014/53/EU.
• Technology: Wi-Fi IEEE 802.11 b/g/n.
• Frequencies: 2400-2497 MHz.
• Max. output power: +18.5 dBm.
• The equipment operates in the ISM band at
2.4 GHz.
The complete text of the EU declaration of
conformity is available at the following internet
address:
www.smeg.com/smegconnect/direttiva_red
Declaration art. 10.10
Directive 2014/53/EU
This radio equipment is NOT subject to
restrictions on putting into service or to
requirements concerning authorisation for use in
any of the EU Member States.
This user manual
• This user manual is an integral part of the
appliance and must therefore be kept in its
entirety and within the user's reach for the
whole working life of the appliance.
• Read this user manual carefully before using
the appliance.
• The explanations in this manual include
images, which describe all that regularly
appears on the display. However, it should
be kept in mind that the appliance may be
equipped with an updated version of the
system, and as such, all that appears on the
display may differ from those in the manual.
How to read the user manual
This user manual uses the following reading
conventions:
Warning/Caution
Information/Advice
USE
SmegConnect
The appliance is equipped with SmegConnect
technology that allows the user to control the
appliance operation via an App on his/her
smartphone or tablet.
For further information, refer to the supplied
brochure and/or visit the site
www.smeg.com
Connectivity requirements
• Smartphone or tablet running iOS version
10.x or later or Android version 5.1 or later.
• Wi-Fi network (2.4 GHz band, WPA2
protected) active and available in the place
where the appliance is installed.
• Internet connection.
10 - USE 914779624/A
• Name and password of the home Wi-Fi.
Installation of the App
Download the App SmegConnect on your
mobile smartphone or tablet from App Store
(Apple devices) or Google Play Store (Android
devices) and install it.
Creation of the account
1. Launch the SmegConnect App.
e
2. Enter the information required in order to
register.
The fields marked with an asterisk “*”
are mandatory.
3. A confirmation e-mail is sent to the address
that has been entered when the registration
procedure has been completed.
Product registration
6. Press and hold the light forced
within 30 seconds until it starts flashing.
7. Select Manual mode.
8. Go to the Wi-Fi settings on the mobile
device and select the “smegconnect”
network.
9. Enter the password “smeg0001” and wait
for the connection to be established.
10.Go back to the SmegConnect App and tap
Next.
key
The registration step is formed by alternated
operations to be made in the App and on
the control panel of the appliance . Make
sure you are close to the appliance.
If Connection Failed is
displayed during registration, it means
that some passages of the procedure
did not work properly or were
interrupted.
To remove press the
key (wine cellars with single
compartment) or the display
compartment display
cellars with double compartment).
The procedure can be interrupted at
any time by pressing the
key.
Alarm
for upper
(wine
Connection
Connection to the device
1. Tap Log in.
2. In the following screen (Home page), tap
Add product.
3. Select the type of product you wish to
connect (in this case "wine cellar").
11.Press the
within one minute, to confirm your presence.
The Connection key starts flashing.
12.Enter the Access Point data:
• Name of the home Wi-Fi network.
• Wi-Fi password.
13. Tap Next and wait for the confirmation
page.
14. Wait for the confirmation acoustic signal.
The product registration procedure is
completed.
The device is connected to the Internet and can
be remotely controlled.
Fan key on the appliance
The device supports network names
(SSID) up to 24 digits (including
spaces) and WPA2 security settings
(not WEP or WPA).
During this step, the mobile device
automatically reconnects to the initial
Wi-Fi network or data network. No user
operation is required.
4. Press any key on the device to activate the
control panel.
5. Hold down the Connection key for a
few seconds. The device enters the
SmegConnect menu; the display shows
.
USE - 11914779624/A
Remote connection
Once the device is registered, it can be
connected or disconnected from the
Internet at any time.
The remote connection is only available
if the device has been registered.
5. Press and hold the ON/OFF
30 seconds until it starts flashing.
On some models only, the ON/OFF
key is lit only if the product has already
been registered.
6. Select Manual mode.
7. Go to the Wi-Fi settings on the mobile
device and select the “smegconnect”
network.
8. Enter the password “smeg0001” and wait
for the connection to be established.
9. Go back to the SmegConnect App and tap
Next.
key within
To disconnect the device:
1. At any time, press the
The Connection key stops flashing and
2.
becomes solid again.
To connect the device again:
1. At any time, press the
2. The Connection key starts flashing. For
a few seconds the display will show
alternately with the value of the temperature,
until the Internet connection is completed.
Connection key.
Connection key.
Change Access Point credentials
The procedure can be interrupted at
any time by pressing the
key.
To change your Access Point credentials
(network name or password):
1. Log in the App, tapping Log in.
2. In the Settings menu of the product pages
select Change Access Point.
3. Press any key on the device to activate the
control panel.
4. Hold down the Connection key for a
few seconds. The device enters the
SmegConnect menu; the display shows
.
Connection
10.Press the
within one minute, to confirm your presence.
The Connection key starts flashing.
11.Enter the Access Point data:
• Name of the home Wi-Fi network.
• Wi-Fi password.
12.Tap Next and wait for the confirmation
page.
13.Wait for the confirmation acoustic signal.
The Access Point credentials change procedure
is completed.
The device is connected to the Internet and can
Fan key on the appliance
The device supports network names
(SSID) up to 24 digits (including
spaces) and WPA2 security settings
(not WEP or WPA).
During this step, the mobile device
automatically reconnects to the initial
Wi-Fi network or data network. No user
operation is required.
12 - USE 914779624/A
e
be remotely controlled.
If Connection Failed is
displayed during registration, it means
that some passages of the procedure
did not work properly or were
interrupted.
To remove press the
key (wine cellars with single
compartment) or the display
Alarm
compartment display
cellars with double compartment).
Information on the connection
for upper
(wine
3. Within 30 seconds press simultaneously the
keys
and for a few seconds until
they start flashing.
4. Wait for the confirmation acoustic signal.
This procedure only deletes the
registration and restores the factory
settings for the SmegConnect menu.
The deletion
on the device does not need
the cloud connection.
This type of deletion only affects the
product, please delete the device also
from the App.
Within the App, in the Settings menu of the
product pages you will find information
about the connection, such as:
• device registration date;
• name of the network;
• level of Wi-Fi signal;
• MAC address of the Connectivity board;
• Firmware version of the Connectivity board;
• IPv4 and IPv6 network addresses;
• SW Compliance ID (identification of
compliance with the essential requirements
of the RED directive).
Deletion of the registration
To delete the registration of the device from
the App:
•Go to the Settings menu on the App and
follow the instructions.
The product can be registered again
following the procedure described
above.
To delete the registration of the device on the
product (on some models only):
1. Press any key on the device to activate the
control panel.
2. Hold down the Connection key for a
few seconds. The device enters the
SmegConnect menu; the display shows
.
The product can be registered again
following the procedure described
above.
To delete the registration of the user:
• Go to the My account menu on the App
and follow the instructions of the Privacy
Policy.
Software updates
This stage does not require any activity
of the user.
Software updates are occasionally released
concerning the device connectivity.
If the device is connected to the home Wi-Fi
network, the updates are automatically
downloaded and installed.
The display shows (on some models
only), or
alternated with the
temperature value, or .
During these stages, the connectivity
service is temporarily interrupted.
Updating lasts some minutes.
However, you cannot change the status
of the Connection key or access the
SmegConnect menu and procedures.
During software updates, the devices
operates as usual.
What to do if...
Once the product is registered, the display
USE - 13914779624/A
shows alternating with the temperature
value. If this condition continues for more than
one minute, there might be problems in the
remote connection:
• Check if the Wi-Fi router is switched on.
• Ensure that the Wi-Fi router is not too far.
• Check the conditions of the Wi-Fi network
(2.4 GHz band).
• Check the conditions of the Internet
connection.
• Press the Connection key to disconnect
the device and retry the connection later on.
• Disconnect the device from the socket and
switch it on again after having ascertained
that it switched off.
Product registration or Access Point change
procedures fail:
• Check if the Wi-Fi router is switched on.
• Ensure that the Wi-Fi router is not too far.
• Check the conditions of the Wi-Fi network
(2.4 GHz band).
• Check the availability of the WPA2 data
protection mode.
• Ensure that the name of the network is
shorter than 24 digits (including spaces).
• Check the conditions of the Internet
connection.
• Check the conditions of the data
connection, if the mobile device uses the
latter for Internet.
•Retry later on.
• Disconnect the device from the socket and
switch it on again after having ascertained
that it switched off.
The display shows : device fault:
• Contact technical support.
The App shows : device fault:
• Contact technical support.
For further information see:
• the section Recommendations / FAQ /
Connectivity on the App.
• the web page www.smeg.it/faq/
smegconnect/
14 - USE 914779624/A
Loading...