Page 1
Contents
1.
INSTRUCTIONS FOR SAFE AND PROPER USE________________ 4
2. INSTALLATION OF THE APPLIANCE_________________________ 6
3. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 11
4. FINAL OPERATIONS_____________________________________ 13
5. DESCRIPTION OF CONTROLS ____________________________ 15
6. USE OF THE HOB _______________________________________ 20
7. USE OF THE OVENS_____________________________________ 21
8. AVAILABLE ACCESSORIES _______________________________ 22
9. COOKING HINTS________________________________________ 23
10. CLEANING AND MAINTENANCE ___________________________ 30
11. EXTRAORDINARY MAINTENANCE _________________________ 32
12. PROBLEMS AND CAUSES ________________________________ 34
Thank you for choosing our product.
We advise you to read this manual carefully. It contains all necessary
instructions for maintaining unaltered the appearance and functional
qualities of the cooker.
INSTRUCTIONS FOR THE INSTALLER: these are for the qualified
technician who must carry out a suitable check of the gas system,
install the appliance, set it functioning and carry out an inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice,
description of the commands and the correct procedures for cleaning
and maintenance of the appliance.
3
Page 2
Introduction
1. INSTRUCTIONS FOR SAFE AND PROPER USE
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE
PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE
READING THIS MANUAL AND ALL THE INSTRUCTIONS THERE IN BEFORE
USING THE COOKER.
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN
ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS
INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT
REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY
OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD.
ALL OTHER USES ARE CONSIDERED IMPROPER.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER
USE.
DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE
THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST
SPECIAL GARBAGE COLLECTION CENTRE.
IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED
ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION
TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW.
SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE
SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.
ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION
(OFF) WHEN YOU FINISH USING THE HOB.
NEVER PUT INFLAMMABLE OBJECTS INTO AN OVEN: IF THEY CATCH FIRE
THEY COULD CAUSE A FIRE IN THE HOME.
4
Page 3
Introduction
THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND
BRAND NAME IS POSITIONED VISIBLY IN THE STORAGE COMPARTMENT.
THE PLATE MUST NOT BE REMOVED.
DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS
ON THE HOB GRIDS.
DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE
OUTER PERIMETER OF THE HOB.
THE APPLIANCE IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW
CHILDREN OR INFIRM PERSONS TO GO NEAR OR PLAY WITH IT.
DURING USE THE APPLIANCE BECOMES HOT. CARE SHOULD BE TAKEN
TO AVOID TOUCHING THE HEATING ELEMENTS INSIDE THE OVEN. KEEP
CHILDREN AWAY FROM THE OVEN.
REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE
COLLECTION CENTRE.
THIS APPLIANCE IS DESIGNED FOR COOKING FOOD AND IT SHALL NOT
BE USED AS A SPACE HEATER.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT
IS IN OPERATION.
BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND
PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.
The manufacturer declines all responsibility for damage to persons
or things caused by non-observance of the above prescriptions or by
interference with any part of the appliance or by the use of non-original
spares.
5
Page 4
Instructions for the installer
2. INSTALLATION OF THE APPLIANCE
It is the law that all gas appliances are installed by authorised persons.
Clearance around the cooker must comply with the requirements of
AGA601.
2.1 Electrical connection
Make sure that the power line voltage matches the specifications
indicated on the rating plate located inside the storage compartment.
This rating plate must never be removed.
On the power line, install a two-pole cut-off device with contact cut-off
distance greater than or equal to 3 mm, located in an easily accessible
position near the unit.
If the power cable is replaced, the wire section
on the new cable must not be less than
2.5 mm2(3 x 2.5 cable), keeping in mind that
the end to be connected to the cooker must
have the ground wire (yellow-green) longer by
at least 20 mm. Use only the special cables
available at our Service Centres.
The manufacturer declines all responsibility for damage to persons
or things caused by non-observance of the above prescriptions or by
interference with any part of the appliance.
Overall dimensions: location of
gas and electrical connection
points (all measures in mm).
6
Page 5
Instructions for the installer
2.2 Gas connection
This appliance is suitable for installation with Natural
Gas or LPG. Refer to page 12 for the relevant burner
pressure and appropriate injector sizes. When the
appliance is to be connected to Natural Gas then the
pressure regulator supplied must be fitted to the gas
inlet. A test point (for checking the gas pressure) is
supplied either with the regulator or as a separate fitting
in the case of LPG appliances.
Connection of the appliance to the gas supply must be in
accordance with the requirements of AS5601. A ½” BPS
connector at the inlet is recommended and the gas
supply line to the appliance must be of adequate length
to allow sufficient withdrawal of appliance for service or
disconnection and be:
(a)- annealed copper pipe; or
(b)- a hose assembly complying with requirements of AS 1869 - class B
or equivalent.
The cooker must be installed with provision to allow the gas to be turned
off and disconnected for servicing and removal of the appliance as
required from the gas supply.
Before the cooker is operated make certain all relevant parts are placed
in the correct position.
When the installation is completed the installation connections of cooker
will require to be leak tested, the burner operating pressure and flame
checked and adjusted.
Warranty service calls do not cover these adjustments!
To check the operating pressure of the appliance it is recommended at
least 2 large size burners are used. Ensure appliance is secured to wall
when installation is completed.
N.G. The regulator supplied must be fitted to the ½ BSP thread at the
rear of the appliance. An approved manual shut-off valve must be
installed. The N.G. regulator must be checked and adjusted to 1.0kPa
after installation.
L.P.G. Can be connected to the inlet fitting directly. The
pressure must be checked to ensure it is operating at
2.75kPa.
7
Page 6
Instructions for the installer
2.3 Room ventilation
Caution – This cooker may only be installed and operated in rooms
permanently ventilated in accordance with current regulations. For
proper operation of a gas appliance it is essential for the air necessary
for combustion of the gas to be able to flow naturally into the room. Air
must flow directly into the room through openings in its outside walls.
This (these) opening (s) must have a free passage cross-section of at
least 100 cm2, or 200 cm2 for appliances not equipped with gas safety
device. These openings must be constructed so that they cannot be
obstructed indoors or outdoors, and should preferably be close to the
floor on the side opposite to the combustion gas discharge point. If it is
not possible to make the openings in the room where the cooker is
installed, the necessary air may be taken from an adjoining room,
proveded it is not a bedroom or a room with fire risk.
2.4 Clearance above and around domestic cookers
Extract from AGA601
8
Page 7
Instructions for the installer
REQUIREMENTS
1 Overhead clearances – (Measurement A)
Range hoods and exhaust fans shall be installed in accordance with
the manufacturer’s instructions. However, in no case shall the
clearance between the highest part of the hob of the cooking
appliance and a range hood be less than 600 mm or, for an overhead
exhaust fan, 750 mm.
Any other downward facing combustible surface less than 600 mm
above the highest part of the hob shall be protected for the full width
and depth of the cooking surface area in accordance with Clause
5.12.1.2. However, in no case shall this clearance to any surface be
less than 450 mm.
2 Side clearances – (Measurements B & C)
Where B, measured from the periphery of the nearest burner to any
vertical combustible surface, is less than 200 mm, the surface shall
be protected in accordance with Clause 5.12.1.2 to a height C of not
less than 150 mm above the hob for the full dimension (width or
depth) of the cooking surface area. Where the cooking appliance is
fitted with a ‘splashback’, protection of the rear wall is not required.
3 Additional requirements for Freestanding and Elevated Cooking
Appliaces – (Measurements D & E)
Where D, the distance from the periphery of the nearest burner to a
horizontal combustible surface is less than 200 mm, then E shall be
10 mm or more, or the horizontal surface shall be above the trivet.
See insets above.
NOTES
1 Requirement 3 does not apply to a freestanding or elevated
cooking appliance which is designed to prevent flames or the
cooking vessels from extending beyond the periphery of the
appliance.
2 The ‘cooking surface area’ is defined as that part of the
appliance where cooking normally takes place and does not
include those parts of the appliance containing control knobs.
3 For definition of hob, see Clause 1.4.64.
4 For definition of trivet, see Clause 1.4.109.
5 Consideration is to be given to window treatments when
located near cooking appliances. See Clause 5.3.4.
9
Page 8
Instructions for the installer
2.5 Instruction for wall fixing
1) Fix the screw to the wall and hook the chain (B);
2) Hook the chain to the hole positioned at the rear of the cooker by the
gas pipe (A);
3) Once the chain is in position, push the cooker against the wall;
4) The height of the screw hole from floor level must not exceed 800
mm (C).
A
B
C
1
0
Page 9
Instructions for the installer
3. ADAPTATION TO DIFFERENT TYPES OF GAS
Before performing any cleaning or maintenance work, detach the
appliance from the electrical socket.
The hob of the cooker is adjusted for use with natural gas at a pressure of
1.0kPa. If used with other types of gas, you have to replace the nozzles and
regulate the primary air to the burners. Then adjust the minimum flame on the
gas taps. For nozzle replacement and burner adjustment you must raise the
hob as described in the following paragraph.
3.1 Raising of the hob
Remove the grids, first the middle one then the ones at the sides; remove all
the burner caps, the flame cap crowns and the burners.
1. Remove the programmer buttons;
2. Remove the knobs;
3. Unscrew the front panel fixing screws and remove it after disconnecting
the thermostat tell-tale light faston;
4. Loosen the screws of the hinge on the back of the cooker;
5. Raise the surface from the front end;
6. Place the surface support brackets in the front groove of the side;
7. Proceed to replacement of the burner nozzles in accordance with the
appropriate gas table;
8. Adjust the primary air as described in paragraph “3.2
Adjustment for
LPG
”;
9. After adjustment, fully tighten the fixing screws.
11
Page 10
Instructions for the installer
3.2 Adjustment for LPG
Loosen screw A and push air regulator B to
the bottom. With a 7 mm wrench, remove
nozzle C and replace it with the proper one
(follow the instructions on the reference
tables for the type of gas to be used). The
torque wrench setting of the nozzle must not
exceed 3 Nm. Adjust the air by sliding
regulator B until reaching distance “X”
shown in the table in paragraph “3.4
Regulation of primary air”. Lock regulator B
by tightening screw A.
Model CSA19
Models CSA196 / CSA20
LPG – 2.75 kPa
LPG – 2.75 kPa
Burner
Nominal gas
consumption
(MJ/h)
Turn-down gas
consumption
(MJ/h)
Injector
(mm)
Nominal gas
consumption
(MJ/h)
Turn-down gas
consumption
(MJ/h)
Injector
(mm)
Auxiliary 4.80 1.5 0.60 5.30 1.5 0.62
Semi rapid 5.80 1.5 0.67 6.60 1.5 0.70
Rapid 9.30 3.2 0.85 9.00 3.2 0.82
Wok 13.00 5.4 1.00 15.00 5.4 1.05
Fish burner (*) 9.20 3.2 0.85 6.60 2.9 0.70
(*) Models CSA19 / CSA196
3.3 Adjustment for natural gas
The hob has been tested for natural gas at a pressure of 1.0kPa. To
allow the unit to work with this type of gas, perform the same operations
described in paragraph “3.2 Adjustment for LPG”, but choose the nozzles
and adjust the primary air for natural gas, as shown in the following table
and in paragraph “3.4 Regulation of primary air”.
Model CSA19
Models CSA196 / CSA20
NG – 1.00 kPa
NG – 1.00 kPa
Burner
Nominal gas
consumption
(MJ/h)
Turn-down gas
consumption
(MJ/h)
Injector
(mm)
Nominal gas
consumption
(MJ/h)
Turn-down gas
consumption
(MJ/h)
Injector
(mm)
Auxiliary 5.30 1.4 1.04 5.30 1.4 1.00
Semi rapid 6.60 1.4 1.15 6.60 1.4 1.15
Rapid 9.00 2.4 1.35 9.00 2.4 1.35
Wok 12.50 4.3 1.65 15.00 4.3 1.75
Fish burner (*) 10.20 3.2 1.45 6.60 2.9 1.15
(*) Models CSA19 / CSA196
1
2
Page 11
Instructions for the installer
3.4 Regulation of primary air
Referred to distance “X” in mm.
Models CSA19 / CSA196 / CSA20
Burner
NG
1.00 kPa
LPG
2.75 kPa
Auxiliary 3.0 2.5
Semi rapid 3.0 2.0
Rapid 3.0 2.0
Wok 4.0 2.5
Fish burner (*) 4.0 4.0
(*) Models CSA19 / CSA196
4. FINAL OPERATIONS
Having carried out the above adjustments, reassemble the appliance
following, backwards, the instructions in paragraph “3.1 Raising of the
hob”.
4.1 Adjustment of minimum for natural gas
Light the burner and take it to the minimum .
Remove the gas tap knob and turn the
adjustment screw inside or at the side of the tap
shaft (depending on the model) until there is a
regular minimum flame. Replace the knob and
check burner flame stability: (rapidly turning the
knob from maximum to minimum position, the
flame should not go out). Repeat the operation on
all the gas taps.
4.2 Adjustment of minimum for LPG
To regulate the minimum for LPG, completely tighten (clockwise) the
screw inside or next to the gas tap pin (depending on the model).
1
3
Page 12
Instructions for the installer
4.3 Arrangement of burners on the hob
Model CSA19 Model CSA196
Model CSA20 Burners
1 Auxiliary
2 Semi rapid
3 Rapid
4 - 5 Wok
6 Fish burner
4.4 Positioning and levelling of the appliance
Having carried out the electricity and gas hook-up, level the appliance
using the four adjustable legs.
4.5 Lubrication of gas taps
With time it may happen that the gas taps get blocked and hard to turn.
Clean them inside and re-grease them. This operation must be done
by an authorised person.
1
4
Page 13
Instructions for the user
5. DESCRIPTION OF CONTROLS
5.1 Front control panel
All the cooker controls and commands are on the front panel.
Model CSA19
Model CSA196
Model CSA20
Before using the main oven check that the electronic programmer is
showing the symbol (see paragraph “5.2.1 Clock adjustment”).
DESCRIPTION OF SYMBOLS
BACK LEFT BURNER
BACK RIGHT BURNER
FRONT LEFT BURNER
FRONT RIGHT BURNER
WHERE AVAILABLE
FRONT CENTRAL
BURNER
BACK CENTRAL
BURNER
CENTRAL
BURNER
MAIN OVEN
THERMOSTAT
AUXILIARY OVEN
THERMOSTAT
MAXI OVEN
THERMOSTAT
MAIN OVEN
FUNCTIONS
AUXILIARY OVEN
FUNCTIONS
MAXI OVEN
FUNCTIONS
1
5
Page 14
Instructions for the user
HOB BURNER COMMAND KNOB
The flame is lit by pressing the knob and turning it
anticlockwise to maximum flame . To adjust the flame
turn the knob between maximum ( ) and minimum ( ).
The burner goes out when the knob is returned to the
position .
THERMOSTAT KNOB (OVENS)
Selection of cooking temperature is carried out by turning
the knob clockwise to the required temperature, between
50° and 250°C. The tell-tale light comes on to indicate
that the oven is warming up. When it goes out it means
that the required temperature has been reached. Regular
flashing means that oven temperature is being constantly
maintained at the programmed level.
FUNCTION SWITCH KNOB (OVENS)
Turn the knob to select from the following functions:
MAIN OVEN AUXILIARY OVEN (MODEL CSA20)
NO FUNCTION SET
NO FUNCTION SET
OVEN LIGHT
OVEN LIGHT
UPPER AND LOWER
HEATING ELEMENT
UPPER AND LOWER
HEATING ELEMENT
GRILL ELEMENT
UPPER HEATING ELEMENT
GRILL ELEMENT + VENTILATION
LOWER HEATING ELEMENT
LOWER HEATING ELEMENT +
VENTILATED HEATING ELEMENT
GRILL ELEMENT
VENTILATED HEATING ELEMENT +
VENTILATION
GRILL + SPIT ELEMENT
16
Page 15
Instructions for the user
5.2 Electronic Programmer
The programmer user instructions are valid only for the main oven.
LIST OF FUNCTIONS
MINUTE-COUNTER KEY
COOKING TIME KEY
END-OF-COOKING KEY
DECREASE TIME KEY
INCREASE TIME KEY
5.2.1 Clock adjustment
When using the oven for the first time, or after a power failure, the display
flashes regularly and indicates
. Press the keys and at
the same time the keys
o : each single press changes the time by
1 minute either up or down.
Before setting the programmer activate the desired function and
temperature.
17
Page 16
Instructions for the user
5.2.2 Semiautomatic cooking
Use this setting for automatic oven switch-off at the end of cooking time.
By pressing key
, the display lights up, showing ; keep the key
pressed and at the same time, press keys
o to set the cooking
time.
Release key
to start the programmed cooking time count. The display
will now show the right time together with symbols A and
.
5.2.3 Automatic cooking
Use this setting to automatically start and stop the oven.
By pressing key
, the display lights up showing ; keep the key
pressed and at the same time, press keys
or to set the cooking
time.
By pressing key
the sum of the right time + cooking time will appear;
keep the key pressed and at the same time, press keys
o to
regulate the end of cooking time.
Release key
to start the programmed count and the display will show
the right time together with symbols A and
.
After set-up, to see the cooking time remaining, press the key ; to see
the end of cooking time press the key .
Set-up with incoherent values is logically prevented (e.g. the contrast
between a cooking time and a longer period will not be accepted by the
programmer).
5.2.4 End of cooking
When cooking is over, the oven will automatically switch off and, at the
same time, an intermittent alarm will sound. After switching off the alarm,
the display will once again show the right time together with the symbol
, indicating that the oven has returned to manual operation mode.
1
8
Page 17
Instructions for the user
5.2.5 Adjusting alarm volume
The acoustic alarm has three different settings. These can be operated,
while the alarm is sounding, by pressing key
.
5.2.6 Switching off the alarm
The alarm switches off automatically after seven minutes. They can be
manually de-activated by pressing the keys
and together.
5.2.7 Minute Counter
The programmer can also be used as a simple minute counter. By
pressing key
, the display shows ; keep the key pressed and
at the same time press keys
o . On releasing the key ,
programmed counting will begin and the display will show the current
time and the symbol
.
After set-up, to see the remaining time, press the key .
Use as a minute counter does not interrupt functioning of the oven at the
end of the programmed time.
5.2.8 Cancellation of set data
Once the programme has been set, keep the key of the function to be
cancelled pressed, while at the same time
is reached by means
of variation keys
o . Time cancellation will be considered as end-of-
cooking time by the programmer.
5.2.9 Changing the set data
The cooking data entered can be changed at any time by keeping the
function key pressed and at the same time adjusting the keys
o .
1
9
Page 18
Instructions for the user
6. USE OF THE HOB
6.1 Lighting of the hob burners
Before lighting the hob burners check that the flame cap crowns are
properly positioned with their appropriate burner caps: niche A must be
centred with pin B.
Grid C should be used with Chinese woks.
Each knob corresponds to the burner indicated. The appliance is
equipped with an electronic lighting device. Just press and turn the knob
anticlockwise to the maximum flame symbol until the burner lights.
Keep the knob pressed for about 2 seconds to let the thermocouple heat
up. If the burner turns off when the knob is released, it means that the
thermocouple isn’t hot enough. Repeat ignition and keep the knob
pressed longer.
If the burners turn off accidentally, a safety device will trip after about 20
seconds to cut off gas flow (even with the gas tap open).
6.2 Practical advice for using the hob burners
For better use of the burners and lower gas consumption, use covered
containers that are proportional in size to the burner to prevent the flame
from licking the sides (see paragraph “6.3 Diameter of containers”).
When water reaches the boiling point, lower the flame so that it doesn’t
overflow. To avoid burns or damage to the hob, all recipients or griddle
plates must be placed within the perimeter of the hob. All containers
have to have a flat and smooth bottom. When using fats or oils, be
extremely careful that they don’t overheat and catch fire.
If the flame accidentally goes out, turn off the control knob and wait at
least 1 minute before trying to re-light the burner.
2
0
Page 19
Instructions for the user
6.3 Diameter of containers
Models CSA19 / CSA196 / CSA20
(*)
Burners
Ø min. and max. (in cm)
1
Auxiliary 12-14
2
Semi rapid 16-20
3
Rapid 18-24
4
Wok 20-26
5
Wok (Model CSA20) 20-24
6
Fish burner (Models CSA19 / CSA196) Special oval-shaped pan
(*) For burner reference numbers, see page 14.
7. USE OF THE OVENS
7.1 Warnings and general advice
Before using the oven for the first time, pre-heat it to maximum
temperature (250°C) long enough to burn any manufacturing oily
residues which could give the food a bad taste.
After a power failure, the display will flash at regular intervals showing
. To regulate, refer to paragraph "5.2 Electronic Programmer”.
To prevent any steam in the oven creating
problems, open the door in two stages: half open (5
cm approx.) for 4-5 seconds and then fully open.
To access food, always leave the door open as
short a time as possible to prevent the temperature
in the oven from falling and ruining the food.
7.2 Oven Light
It comes on when the function switch knob is turned to any position.
7.3 Storage compartment
A storage compartment, accessible by
pulling on the top edge of the door, is located
beneath the ovens. Never store inflammable
materials such as rags, paper or the like.
The compartment is intended only for
holding the metal accessories of the range.
21
Page 20
Instructions for the user
8. AVAILABLE ACCESSORIES
The oven features 4 support positions for
plates and racks of different height.
Models CSA19 / CSA196
Model CSA20
Main
Auxiliary
Oven grill: for cooking food
on plates, small cakes, roasts
or food requiring light grilling.
Plate grill: for placing above
plate for cooking foods that
might drip.
Oven plate: useful for
catching fat from foods on the
grill above.
Pastry plate: for baking
cakes, pizza and oven
desserts.
Auxiliary oven
Roasting spit: useful for
cooking chicken, sausages
and anything else requiring
uniform cooking over the
whole surface.
Spit Frame: to be inserted in
the guides of the oven before
using the spit.
Spit supports: to be inserted
in the holes of the oven plate
before mounting the roasting
spit.
Accessories on Request
You can order the lower base and self-cleaning oven panels through
Authorised Assistance Centres.
2
2
Page 21
Instructions for the user
9. COOKING HINTS
9.1 Traditional cooking
FUNCTION SWITCH
THERMOSTAT SELECTOR SWITCH FROM
50° TO 250°C
This traditional cooking method, in which heat comes from above and
below, is suitable for cooking food on a single level. You have to preheat the oven until the set temperature is reached. Place the food in the
oven only after the thermostat indicator light has turned off. very fatty
meats may be put in when the oven is still cold. Put frozen meat in
immediately, without waiting for it to thaw. The only precaution you need
to take is to set the temperature about 20°C lower and cooking time
about 1/4 longer than you would for fresh meat.
Use high-rim pans to prevent fat splashing and
dirtying the sides of the oven.
9.2 Hot-air cooking (main oven)
FUNCTION SWITCH
THERMOSTAT SELECTOR SWITCH FROM
50° TO 250°C
This system is suitable for cooking on several levels, including different
types of food (fish, meat etc.), without the tastes and smells mingling. Air
circulation in the oven ensures a uniform distribution of heat. Pre-heating
is not necessary.
23
Page 22
Instructions for the user
Multiple cooking is possible as long as the cooking temperature of the
different foods is the same.
9.3 Grill cooking
FUNCTION SWITCH
THERMOSTAT SWITCH AT MAXIMUM
Permits rapid browning of foods. You are advised to place the pan in the
highest guide. For short-term cooking of small quantities, place the grid
in the third guide from the bottom. For long-term cooking and grills, put
the grid in the lowest guide in accordance with the size of the pieces.
Make sure that the oven door is closed during cooking.
9.4 Hot-air grilling (main oven)
FUNCTION SWITCH
THERMOSTAT SWITCH FROM 50° TO 200°C
Ensures uniform heat distribution with greater heat penetration into the
food. Food will be lightly browned on the outside and remain soft inside.
Keep the oven door closed during cooking. Heating up time must
not exceed 60 minutes.
2
4
Page 23
Instructions for the user
9.5 Delicate cooking (auxiliary oven of model CSA20)
FUNCTION SWITCH
THERMOSTAT SELECTOR SWITCH FROM
50° TO 250°C
Ideal for pastries and cakes with wet covering and little sugar and damp
desserts in moulds. Excellent results can also be achieved in completing
cooking at the bottom and with dishes requiring heat in the lower area in
particular. The plate is best inserted at bottom level.
9.6 Defrosting (main oven)
FUNCTION SWITCH
THERMOSTAT SWITCH IN POSITION 0
The flow of air produced by the fan ensures quicker defrosting.
The air circulating inside the oven is at room temperature.
The advantage of defrosting at room temperature is that it does not alter
the taste and appearance of the food.
2
5
Page 24
Instructions for the user
9.7 Spit cooking (Models CSA19 / CSA196)
FUNCTION SWITCH
THERMOSTAT SWITCH AT MAXIMUM
Insert the food to be cooked on to the rod and tighten screws A of the
forks. Fit frames B into the holes of the bowl F. Remove handle D and
position the spit rod so that pulley E fits into the slot on the right-hand
side of frame B. Completely introduce the bowl into the oven until the tip
of the rod of frame B on the left-hand side fits into drive seat C of the spit
motor on the back wall of the oven. Pour a bit of water into the pan to
avoid smoke from the dripping.
Make sure that the oven door is closed during cooking.
It is normal for the thermostat light to flash during cooking. This indicates
the temperature inside the oven is regular.
2
6
Page 25
Instructions for the user
9.8 Spit cooking (auxiliary oven of model CSA20)
FUNCTION SWITCH
THERMOSTAT SWITCH AT MAXIMUM
This type of cooking is only for the auxiliary oven. Use it for small size
pieces.
Prepare the spit with the food, blocking fork screws A. Insert frame B
into the third guide from the bottom. Remove handle D and position the
spit shaft so that pulley E is guided on the link of frame B. Fully insert
frame B until the point of the spit shaft enters the spit-turning motor
housing C on the rear wall of the oven. Position pan F on the lowest
guide and pour a little water in to avoid smoke forming.
Make sure that the oven door is closed during cooking.
It is normal for the thermostat light to flash during cooking. This indicates
the temperature inside the oven is regular.
2
7
Page 26
Instructions for the user
9.9 Recommended cooking table
Cooking times, especially meat, vary according to the thickness and
quality of the food and to consumer taste.
TRADITIONAL COOKING
LEVEL
FROM BELOW
TEMPERATURE
(°C)
TIME IN
MINUTES (*)
FIRST COURSES
LASAGNE
OVEN-BAKED PASTA
2 - 3
2 - 3
210 - 230
210 - 230
30
40
MEAT
ROAST VEAL
ROAST BEEF
ROAST PORK
CHICKEN
DUCK
GOOSE - TURKEY
RABBIT
LEG OF LAMB
2
2
2
2
2
2
2
1
170 - 200
210 - 240
170 - 200
170 - 200
170 - 200
140 - 170
170 - 200
170 - 200
30 - 40 / KG.
30 - 40 / KG.
30 - 40 / KG.
45 - 60
45 - 60
45 - 60
50 - 60
15 / KG.
ROAST FISH 1 - 2 170 - 200 ACCORDING TO
DIMENSIONS
PIZZA 1 - 2 210 - 240 40 - 45
DESSERTS
MERINGUE
SHORT PASTRY
CIAMBELLA
SAVOYARDS
BRIOCHES
FRUIT CAKE
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
1 - 2
50 - 70
170 - 200
165
150
170 - 200
170 - 200
60 - 90
15 - 20
35 - 45
30 - 50
40 - 45
20 - 30
(*) = WITH PREHEATED OVEN
GRILLING
LEVEL
FROM BELOW
TIME IN MINUTES
FIRST SURFACE SECOND SURFACE
PORK CHOPS
FILLET OF PORK
FILLET OF BEEF
LIVER
VEAL ESCALOPES
HALF CHICKEN
SAUSAGES
MEAT-BALLS
FISH FILLETS
TOAST
4
3
3
4
4
3
4
4
4
4
7 - 9
9 - 11
9 - 11
2 - 3
7 - 9
9 - 14
7 - 9
7 - 9
5 - 6
2 - 4
5 - 7
5 - 9
9 - 11
2 - 3
5 - 7
9 - 11
5 - 6
5 - 6
3 - 4
2 - 3
2
8
Page 27
Instructions for the user
HOT-AIR COOKING
LEVEL
FROM BELOW
TEMPERATURE
(°C)
TIME
IN MINUTES
FIRST COURSES
LASAGNE
OVEN-BAKED PASTA
CREOLE RICE
2
2
2
190 - 210
190 - 210
190 - 220
20 - 25
25 - 30
20 - 25
MEAT
ROAST VEAL
ROAST PORK
ROASTED BEEF
FILLET OF BEEF
ROAST LAMB
ROAST BEEF
ROAST CHICKEN
ROAST DUCK
ROAST TURKEY
ROAST RABBIT
ROAST HARE
ROAST PIGEON
2
2
2
2
2
2
2
2
2
2
2
2
150 - 170
150 - 160
160 - 170
160 - 180
130 - 150
170 - 180
170
160 - 170
150 - 160
150 - 160
160 - 170
140 - 170
65 - 90
70 - 100
65 - 90
35 - 45
100 - 130
40 - 45
70 - 90
100 - 160
160 - 240
80 - 100
30 - 50
15 - 25
FISH 2 - 3 150 - 170 ACCORDING
TO DIMENSIONS
PIZZA 2 - 3 210 - 240 30 - 50
DESSERTS (PASTRIES)
CIAMBELLA
FRUIT CAKE
SPONGE-CAKE
BRIOCHES
STRUDEL
SAVOYARD PUDDING
BREAD
TOAST
2 - 3
2 - 3
2 - 3
2 - 3
1 - 2
2 - 3
2 - 3
1 - 2
150 - 170
170 - 190
190 - 220
160 - 170
150
160 - 170
190 - 210
220 - 240
35 - 45
40 - 50
25 - 35
40 - 60
25 - 35
30 - 40
40
7
29
Page 28
Instructions for the user
10. CLEANING AND MAINTENANCE
10.1 Cleaning stainless steel
To keep stainless steel in good condition it should be cleaned regularly
after use. Let it cool first.
10.1.1 Ordinary Daily Cleaning
To clean and preserve the stainless steel surfaces, always use only
specific products that do not contain abrasives or chlorine-based acids.
How to use: pour the product on a damp cloth and wipe the surface,
rinse thoroughly and dry with a soft cloth or deerskin.
10.1.2 Food stains or residues
Do not use metallic sponges or sharp scrapers: they will
damage the surface.
Use normal non-abrasive products for steel, and a wooden or
plastic tool if necessary.
Rinse thoroughly and dry with a soft cloth or deerskin.
10.2 Cleaning of the hob components
10.2.1 Grids
Extract the grids (the central one first, then the side ones). Clean with
warm water and non-abrasive detergent, taking care to remove
incrustation. Reassemble positioning the side ones first and then the
central one.
30
Page 29
Instructions for the user
10.2.2 Burner caps, flame cap crowns and burners
To facilitate cleaning, caps, flame cap crowns, and burners are all
removable. To remove the flame separating crown of the fish hob, loosen
the two screws exposed after having removed the cap. Wash all parts
with warm water and non-abrasive detergent taking care to remove all
tough spots. Wait for all parts to be fully dry before remounting.
Re-install the caps on the corresponding crowns making sure that
grooves A are perfectly aligned with pins B of the burners. Re-tighten the
securing screws of the fish hob flame cap crown.
10.2.3 Ignition plugs and thermocouples
To work well, the ignition plugs and thermocouples must always be very
clean. Check them frequently and clean them with a wet rag if
necessary. Any dry residue should be removed with a toothpick or a
needle.
10.3 Cleaning of ovens (without self-cleaning panels)
To keep an oven in good condition it must be cleaned regularly. Let it
cool first. Take out all the removable parts.
Remove the side guides by raising them at the front. Free them from the
rear hole and extract them.
• Clean the oven grill and side guides with hot water and non-abrasive
detergent. Rinse and dry.
31
Page 30
Instructions for the user
• Clean the internal walls of the oven with a soft ammoniac-soaked
cloth. Rinse and dry. If there are still stains or drops, place a damp
ammoniac-soaked cloth on the bottom of the oven, close the door
and after a few hours wash the oven with hot water and liquid
detergent. Rinse and dry.
10.4 Door glass
These should always be kept very clean. Use absorbent kitchen paper or,
in case of hard to remove dirt, wash with a wet sponge and ordinary
detergent.
11. EXTRAORDINARY MAINTENANCE
Ovens periodically require small maintenance interventions or
replacement of parts subject to wear and tear such as gaskets, electric
bulbs etc. Specific instructions for each intervention of this type appear
below.
Before performing any operations requiring access to powered
parts, switch off the power supply to the machine.
11.1 Replacement of light bulbs
Remove cover A by twisting anticlockwise, replace bulb B with another
similar bulb. Refit the cover A.
Only use oven bulbs (T 300°C).
32
Page 31
Instructions for the user
11.2 Dismantling of the doors
Hold the door on both sides
with both hands near hinges
A and raise levers B. Lift up
the door forming an angle of
about 45° and remove. To
refit, slide the hinges A in the
grooves, drop the door and
release levers B.
11.3 Oven door gaskets
The door gaskets can be dismantled for thorough
cleaning of the ovens. Before removing the gaskets the
oven doors must be removed as previously described.
With the doors removed, raise the tabs at the corners
as shown in the figure.
11.4 Preventive maintenance
This appliance does not need any special maintenance. However, a few
simple operations have to be carried out periodically to prevent
malfunctioning:
Burners: the burners must be cleaned periodically to ensure correct
combustion; make sure that all the openings and flame ports are clean and
free of obstacles, and that the burners rest firmly on their supports.
Gas connection: the gas connection must be checked periodically. Each
time the cooker is moved the connection may be stressed: test it for
leakages using special sprays or a solution of soap and water.
Flexible pipes: if a flexible pipe is used, it must be inspected periodically
(once a year) for leakages: if the surface of the pipe appears rigid and
cracked, disconnect immediately the cooker from the gas supply and
replace the pipe with a new one.
Valves: if the gas valves get stuck or hard to turn, they need to be cleaned
and re-greased; this operation must be carried out by an authorised person.
Oven gasket: with time the oven gasket may harden and crack on the
surface, resulting in leakage of heat from the oven and higher temperatures
on the control panel and knobs. Check it periodically and replace it if
necessary.
33
Page 32
Instructions for the user
12. PROBLEMS AND CA USES
Each of the following cases is caused by an abnormal operation of the
appliance and should be dealt with by a skilled operator: please contact
your local dealer or Service Center in case you detect any of these
malfunctioning.
PROBLEM
CAUSE
WHAT TO DO
The flame is very long with
bright yellow tips.
Black deposits on the
bottom of the pans.
Defect of comburent air
or incorrect injectors.
Call Service Center.
The flame is very short and
noisy. The flame moves
away from the burner ports.
Excess of comburent
air.
Call Service Center.
The flame extinguishes
when the burner knob is set
to the low flame position.
Incorrect adjustment of
the minimum heat input
or excess of comburent
air.
Call Service Center.
The valve knob is hard to
rotate.
Gas valve worn out or
needs lubrification.
Call Service Center.
The cooker suddenly stops
working during operation of
the oven.
The electronic programmer
is not operating.
Overheating of the
appliance.
Let the appliance cool
down: the safety thermal
cut-out will self-reset
when the temperature
has decreased to a
correct value. Should the
problem arise again, call
the Service Center.
3
4
Loading...