Smeg CIR575XS5 User manual [GB]

Contents

3

1. INSTRUCTIONS FOR SAFE AND PROPER USE ________________ 4

2. POSITIONING OF THE HOB ________________________________ 6

3. GAS CONNECTION ______________________________________ 10

4. ELECTRICAL CONNECTION _______________________________ 12

5. ADAPTATION TO DIFFERENT TYPES OF GAS ________________ 13

6. FINAL OPERATIONS _____________________________________ 15

7. USING THE HOB _________________________________________ 17

8. CLEANING AND MAINTENANCE ____________________________ 20

9. PROBLEMS AND CAUSES _________________________________ 22

Thank you for choosing our product.
We advise you to read this manual carefully. It contains all necessary
instructions for maintaining unaltered the appearance and functional
qualities of the hob.

NSTRUCTIONS FOR THE INSTALLER: these are for the authorised
persons who must carry out a suitable check of the gas system, install
the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,
description of the commands and the correct procedures for cleaning
and maintenance of the appliance.

Instructions for the installer

1. INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE
PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE
READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE
USING THE HOB.
INSTALLATION MUST BE CARRIED OUT BY AN AUTHORISED PERSON IN
ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS
INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT
REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY
OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD.
ALL OTHER USES ARE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER
USE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE
THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST
SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED
ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE SOCKET
MUST BE THE SAME TYPE AND MUST CONFORM TO CURRENT
REGULATIONS.
NEVER UNPLUG BY PULLING ON THE CABLE.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION
TEST OF THE HOB, FOLLOWING THE INSTRUCTIONS BELOW. SHOULD
THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND
CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION
"ZERO" (OFF) WHEN YOU FINISH USING THE HOB.

NEVER USE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.

DO NOT MODIFY THIS APPLIANCE

Instructions for the installer

5

THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER
AND MARKING IS CLEARLY VISIBLE UNDER THE CASING.

THE DUPLICATE DATA PLATE MUST BE ATTACHED TO AN ADJACENT
SURFACE.

BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN
REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING
THE LABEL UNDER THE CASING.

DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT
BOTTOMS ON THE HOB GRIDS.

DO NOT USE RECIPIENTS OR GRIDDLE PLATES THAT EXTEND
BEYOND THE EXTERNAL PERIMETER OF THE HOB.

THE HOB IS TO BE USED BY ADULTS ONLY. DO NOT LET
UNSUPERVISED CHILDREN PLAY WITH THE HOB.

REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE
COLLECTION CENTRE.

WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN
CARAVANS, IT SHALL NOT BE USED AS A SPACE HEATER.

THIS APPLIANCE IS DESIGNED FOR COOKING FOOD AND IT SHALL
NOT BE USED AS A SPACE HEATER.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE
WHILE IT IS IN OPERATION.

ALL SERVICING AND MAINTENANCE ARE TO BE COMPLETED BY THE
MANUFACTURER’S AUTHORISED PERSONNEL ONLY.

The manufacturer declines all responsibility for damage to
persons or things caused by non-observance of the above
prescriptions or by interference with any part of the appliance or by
the use of non-original spares.

Instructions for the installer

2. POSITIONING OF THE HOB

It is the law that all gas appliances are installed by authorised persons.
Clearance around the appliance must comply with the requirements of
AS5601.
The following operation requires building and/or carpentry work so must
be carried out by a competent tradesman. Installation can be carried out
on various materials such as masonry, metal, solid wood or plastic
laminated wood as long as they are heat resistant (T 90°C).

2.1 Attachment to support structure

Create an opening with the dimensions shown in the figure in the top
surface of the counter, keeping a minimum distance o
If 50 mm from the rear border. This appliance is classified as "type Y" in
relation to fire hazards and can therefore be mounted against walls
higher than the work surface on condition that a certain distance “X” be
kept between the appliance and the wall as shown in the figure so as to
avoid damage from overheating. Make sure there is a minimum of 600
mm between the hot plate flames and any shelf that may be installed
directly above them.

Accurately position the gasket provided all around the outer edge of the
hole in the top surface as shown in the figures below, pressing it down so
as to make it adhere properly. For measurements, refer to the figure
depending on the hob model to be installed, bearing in mind that in both
models the front and rear sides must skim the hole. Secure the hob to the
counter with brackets A (supplied). Carefully trim any excess from border

B of the gasket. The distances in the following drawing refer to the hole
on the inner side of the gasket.

Instructions for the installer

7

Overall dimensions: location of gas and electrical connection points (all
measures in mm).

30 CM

HOB

70 CM

HOB A 60

120 B 90

90 C 30

30 D 90

70

Instructions for the installer

2.2 Clearance above and around domestic appliances

Extract from AS5601

REQUIREMENTS
1 Overhead clearances – (Measurement A)

Range hoods and exhaust fans shall be installed in accordance with

the manufacturer’s instructions. However, in no case shall the

clearance between the highest part of the hob of the cooking
appliance and a range hood be less than 600 mm or, for an overhead

exhaust fan, 750 mm.
Any other downward facing combustible surface less than 600 mm

above the highest part of the hob shall be protected for the full width
and depth of the cooking surface area in accordance with Clause

5.12.1.2. However, in no case shall this clearance to any surface be
less than 450 mm.