Page 1
Contents
@
1. INSTRUCTIONS FOR USE ..................................................................................................... 4
2. SAFETY PRECAUTIONS ........................................................................................................ 6
3. ENVIRONMENTAL CARE ....................................................................................................... 8
3.1 Our environmental care .................................................................................................................................. 8
3.2 Your environmental care ................................................................................................................................. 8
4. GET TO KNOW YOUR APPLIANCE ....................................................................................... 9
4.1 Description of the controls on the front panel ............................................................................................... 10
5. AVAILABLE ACCESSORIES ................................................................................................. 11
5.1 Using the rack or tray .................................................................................................................................... 11
5.2 Using the support rack .................................................................................................................................. 12
5.3 Using the reduction pan stands .................................................................................................................... 12
6. USING THE COOKING HOB ................................................................................................. 13
6.1 General warnings and advice ....................................................................................................................... 13
6.2 Lighting the hob burners ............................................................................................................................... 13
6.3 Practical hints for using the hob burners ....................................................................................................... 13
6.4 Pan diameters ............................................................................................................................................... 14
7. USING THE OVEN ................................................................................................................ 15
7.1 Before using the appliance ........................................................................................................................... 15
7.2 Oven runners ................................................................................................................................................ 15
7.3 Storage compartment (on some models only) .............................................................................................. 15
7.4 Cooling system ............................................................................................................................................. 15
7.5 Internal light .................................................................................................................................................. 15
7.6 General warnings and advice for use ........................................................................................................... 16
7.7 Using the bottom burner ............................................................................................................................... 17
7.8 Using the electric grill .................................................................................................................................... 17
8. COOKING WITH THE OVEN ................................................................................................18
8.1 Cooking advice and instructions ................................................................................................................... 19
8.2 Cooking operation information table ............................................................................................................. 20
9. CLEANING AND MAINTENANCE ......................................................................................... 21
9.1 Cleaning stainless steel ................................................................................................................................ 21
9.2 Ordinary daily cleaning ................................................................................................................................. 21
9.3 Food stains or residues ................................................................................................................................. 21
9.4 Cleaning the cooking hob parts .................................................................................................................... 21
9.5 Cleaning the oven ......................................................................................................................................... 22
10. EXTRAORDINARY MAINTENANCE .................................................................................. 24
10.1 Replacing the light bulb ............................................................................................................................... 24
10.2 Removing the door ...................................................................................................................................... 24
10.3 Removing the door seal (not on pyrolitic models) ....................................................................................... 25
10.4 Removing the internal glass panels ............................................................................................................ 25
11. INSTALLATION .................................................................................................................. 26
11.1 Installing in kitchen units ............................................................................................................................. 26
11.2 Room ventilation and combustion extraction .............................................................................................. 27
11.3 Gas connection ........................................................................................................................................... 28
11.4 Electrical connection ................................................................................................................................... 30
11.5 Positioning the skirt (on some models only) ................................................................................................ 31
11.6 Positioning and levelling the appliance ....................................................................................................... 31
12. ADAPTATION TO DIFFERENT TYPES OF GAS .............................................................. 32
12.1 Replacement of nozzles on the hob ............................................................................................................ 32
12.2 Replacing the bottom burner's nozzle ......................................................................................................... 32
12.3 Arrangement of burners .............................................................................................................................. 33
12.4 Final operations .......................................................................................................................................... 33
12.5 Burner and nozzle characteristics table ...................................................................................................... 34
IINSTRUCTIONS FOR THE USER: these instructions contain user recommendations, a
description of the controls and the correct procedures for cleaning and maintenance of the
appliance.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must
install the appliance, set it functioning and carry out an inspection test.
Further information about the products can be found at www.smeg.com
3
Page 2
General instructions
1. INSTRUCTIONS FOR USE
This manual is an integral part of the appliance. It must be kept in its entirety and in an accessible place
for the whole working life of the appliance. We recommend reading this manual and all the information it
contains carefully before using the appliance. Installation must be carried out by qualified personnel in
accordance with the regulations in force. This appliance is intended for domestic use and conforms to
the EC directives currently in force. The appliance has been built to carry out the following functions:
cooking and heating up food; all other uses are considered unsuitable.
These instructions are valid only for the destination countries whose identifying symbols are included on
the cover of this manual.
Never obstruct the openings and slits provided for ventilation and heat dispersal; this may cause
malfunctions.
Do not use this appliance for heating rooms.
This appliance is marked according to European directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
This directive defines the standards for the collection and recycling of waste electrical and electronic
equipment applicable throughout the European Union.
The identification plate with technical data, serial number and brand name is located in an exposed
position either in the drawer (where present) or on the back of the appliance. A copy of the identification
plate is included in the booklet. It should be applied to the appropriate space on the back of the cover. Do
not remove this plate for any reason.
Before the appliance is put into operation, all labels and protective films applied on external surfaces
must be removed.
Do not use metallic sponges or sharp scrapers: they will damage the surfaces. Use normal non-abrasive
products and a wooden or plastic tool if necessary. Rinse thoroughly and dry using a soft cloth. Do not
allow residues of sugary foods (such as jam) to set for too long, as this may spoil the enamel on the
inside the oven.
Do not use plastic kitchenware or containers. The high temperatures inside the oven could melt the
plastic, damaging the appliance.
Always check that the control knobs are in the “zero” (off) position when you finish using the appliance.
Do not use sealed tins or containers in the appliance. Overpressure may occur inside the containers
during cooking, creating a danger of explosion.
Do not cover the bottom of the oven with aluminium or tinfoil sheets during cooking and do not place
pans or trays on it to avoid damage to the enamelled surface.
Never place saucepans with bases which are not perfectly flat and smooth on the hob. Unstable
cookware can lead to scalding.
Do not rest any weight or sit on the open door of the appliance. Excessive weight may jeopardise its
stability.
4
Page 3
General instructions
The appliance becomes very hot during use. Suitable heat-proof gloves should be worn for all
operations.
Do not use the hob if pyrolysis (where present) is taking place inside the oven.
If you intend to go away for a prolonged period of time, close the mains gas tap or the gas cylinder tap.
Take care that no objects are stuck in the door of the oven.
Do not open the storage compartment (where present) when the oven is on and still hot. The
temperatures inside it may be very high.
If the surfaces are still very hot during cooking, do not pour water directly onto the trays. The steam could
cause severe burns and damage enamelled surfaces.
All cooking operations must take place with the door closed. The dissipation of heat may cause hazards.
The manufacturer declines all responsibility for damage to persons or things caused by nonobservance of the above prescriptions or by interference with any part of the appliance or by the
use of non-original spare parts.
5
Page 4
General instructions
2. SAFETY PRECAUTIONS
Consult the installation instructions for safety standards on electrical or gas appliances and for
ventilation functions. In your interests and for your safety the law requires that the installation and
servicing of all electrical and gas appliances be carried out by qualified personnel in accordance with the
regulations in force. Our approved installers guarantee a satisfactory job.
Gas or electrical appliances must always be uninstalled by suitably skilled people.
Before connecting the appliance to the power grid, check the data on the plate against the data for the
grid itself.
If the appliance is installed on a raised platform, secure it using suitable fastening systems.
Before carrying out installation/maintenance work, make sure that the appliance is disconnected from
the power grid.
If the cooking appliances are installed in motor vehicles (for example, camper vans, caravans etc.), they
must only be used when the vehicle is stationary.
Install the appliance so that when opening the drawers or doors of units positioned at the level of the hob
there is no possibility of making contact with pans positioned on top of it.
Immediately after installation, carry out a quick test on the appliance following the instructions provided
later in this manual. Should the appliance not function, disconnect it from the power supply and call the
nearest technical assistance centre.
The plug to be connected to the power supply cable and its socket must be of the same type and
conform to the regulations in force. The socket must be accessible after the appliance has been
installed.
Never disconnect the plug by pulling on the cable.
If the power supply cable is damaged, contact the technical support service immediately and they will
replace it.
The appliance must be connected to earth in compliance with electrical system safety regulations.
During use the appliance and its accessible parts become very hot. Take care never to touch the heating
elements. Keep children younger than 8 away from the appliance, unless under continuous supervision.
Never put inflammable objects in the oven: they could be accidentally ignited and cause fires.
The appliance is intended for use by adults. Do not allow children to go near it or play with it.
This appliance may be used by children from the age of 8 and by people of reduced physical and mental
ability or lacking in experience and knowledge, provided they are supervised or instructed on the safe
use of the appliance and if they understand the associated risks. Do not allow children to play with the
appliance. Do not allow unsupervised children to perform cleaning or maintenance operations.
Never attempt to repair the appliance. All repairs must be carried out by an authorised technician or at
an authorised service centre. The improper use of tools can cause hazards.
6
Page 5
General instructions
This appliance must not be controlled using an external timer or remote control system.
Be aware of how rapidly the cooking zones heat up. Do not place empty saucepans on the heat. Danger
of overheating.
Fats and oils can catch fire if they overheat. You are therefore recommended not to leave the appliance
while preparing foods containing oils or fats. If fats or oils catch fire, never put water on them. Place the
lid on the saucepan and turn off the cooking zone.
Take care when using additional electrical appliances in the kitchen (e.g. blender, toaster etc.).
Connection cables must not come into contact with hot cooking zones.
Do not use steam jets for cleaning the appliance.
The steam could reach the electronics, damaging them and causing short-circuits.
Do not spray any spray products near the household appliance while it is in operation. Do not use spray
products while the appliance is still hot. The gases contained in the spray may catch fire.
The manufacturer declines all responsibility for damage to persons or things caused by nonobservance of the above prescriptions or by interference with any part of the appliance or by the
use of non-original spare parts.
7
Page 6
Instructions for disposal
3. ENVIRONMENTAL CARE
3.1 Our environmental care
Pursuant to Directives 2002/95/EC, 2002/96/EC, 2003/108/EC, relating to the reduction of the use of
hazardous substances in electrical and electronic appliances, as well as to the disposal of refuse, the
crossed out bin symbol on the appliance indicates that the product, at the end of its useful life, must be
collected separately from other refuse. Therefore, the user must consign the product that has reached
the end of its working life to the appropriate selective collection centres for electrical and electronic
refuse, or deliver it back to the retailer when purchasing an equivalent product, on a one for one basis.
Adequate selective collection for the subsequent forwarding of the decommissioned product to recycling,
treatment and ecologically compatible disposal contributes to avoiding possible negative effects on the
environment and on health and promotes the recycling of the materials of which the appliance consists.
The illicit disposal of the product by the user results in the application of administrative sanctions.
The appliance does not contain substances in quantities sufficient to be considered hazardous to health
and the environment, in accordance with current European directives.
3.2 Your environmental care
Our appliances are packed in non-polluting materials, which are therefore compatible with the
environment and recyclable. Please help by disposing of the packaging correctly. You can obtain the
addresses of collection, recycling and disposal centres from your retailer or from the competent local
organisations.
Do not discard the packaging or any part of it, or leave it unattended. It can constitute a
suffocation hazard for children, especially the plastic bags.
Your old appliance also needs to be disposed of correctly.
Important: hand over your appliance to the local agency authorised for the collection of household
appliances no longer in use. Correct disposal enables intelligent recovery of valuable materials.
Before disposing of your appliance it is important to remove doors and leave shelves in the same
position as for use, to ensure that children cannot accidentally become trapped inside during play. It is
also necessary to cut the connecting cable to the power supply network, removing it along with the plug.
8
Page 7
Instructions for the user
4. GET TO KNOW YOUR APPLIANCE
Cooking hob
Control panel
Oven seal
Oven light (double on some
models)
Door sensor (on some models
only)
Rack/tray support frame
Fan
Roof liner (on some models
only)
Door
Bottom gas burner
9
Page 8
Instructions for the user
4.1 Description of the controls on the front panel
4.1.1 Timer knob
This knob allows to set the timer. The numbers indicated are minutes. Adjustment is
progressive so that the time can also be set to any intermediate value between
these numbers. At the end of the set time, a buzzer will sound but cooking will not
be interrupted.
The timer does not stop the cooking operation. It only warns the user that the preset number of minutes
have passed.
4.1.2 Function selection knob
This knob can be used to select the different oven functions.
For furher information see “8. COOKING WITH THE OVEN”.
When using the grill or the fan-assisted grill, the light comes on to signal that the
oven is heating up. When this light goes out, the preset heating temperature has
been reached.
4.1.3 Gas oven thermostat knob
This knob can be used to light the bottom burner inside the oven. The cooking
temperature is selected by turning the knob anti-clockwise to the required setting,
between MIN and MAX.
For further information see “7.7 Using the bottom burner”.
To switch on the light while the bottom burner is being used, turn the timer knob to symbol .
4.1.4 Hob burners control knob
To light the flame, press the knob and turn it anti-clockwise to the maximum flame
symbol ( ). To adjust the flame, turn the knob to the zone between the maximum
10
( ) and the minimum ( ) settings. To turn off the burner, turn the knob to the
position.
(The adjacent symbol indicates the front left burner).
Page 9
Instructions for the user
5. AVAILABLE ACCESSORIES
NOTE: Some models are not provided with all accessories.
Rack: useful for holding
cooking containers.
Tray ra ck : to be placed
over the top of the oven
tray; for cooking foods
which may drip.
Oven tray: useful for
collecting fat from foods
placed on the rack
above.
Reduction pan stand:
useful when using small
pans.
The oven accessories intended to come into contact with food are made of materials that comply with
the provisions of current legislation.
Accessories available on request:
• Original supplied and optional accessories may be ordered from any Authorised Support Centre.
• Use only original accessories supplied by the manufacturer.
Deep oven tray: useful
for baking cakes, pizza
and oven-baked
desserts.
WOK reduction: useful
when using a wok.
5.1 Using the rack or tray
The racks and trays are equipped with a
mechanical safety lock which prevents
them from being taken out accidentally. To
insert the rack or tray correctly, check that
the lock is facing downwards (as shown in
the figure at the side).
To remove the rack or tray, lift the front
slightly.
The mechanical lock (or the extension
piece where present) must always face the
back of the oven.
Gently insert racks and trays into the oven until they come to a stop.
In models with runners, clean the trays before using them for the first time. Cleaning will remove any
manufacturing residues, which may otherwise scratch the sides of the oven cavity when trays are being
inserted.
11
Page 10
Instructions for the user
5.2 Using the support rack
The support rack is inserted into the tray (as shown in the figure). Using
this, foods can be cooked and the fat can be collected separately from the
food which is being cooked.
5.3 Using the reduction pan stands
The reduction pan stands should be placed
on top of the hob racks as shown in the
adjacent figure. Make sure they are stable.
The WOK pan stand should only be used
when cooking with a wok.
12
Page 11
Instructions for the user
6. USING THE COOKING HOB
6.1 General warnings and advice
Before lighting the hob burners, make sure that the flame-spreader crowns are correctly positioned in
their housings with their respective burner caps.
6.2 Lighting the hob burners
All the appliance's control and monitoring devices are placed together on the
front panel. The burner controlled by each knob is shown next to the knob.
The appliance is equipped with an electronic lighter. Simply press the knob
and turn it anti-clockwise to the maximum flame symbol until the burner
lights. If the burner does not light in the first 15 seconds, turn the knob to “0”
and wait 60 seconds before trying again. After lighting, keep the knob
pressed down for a few seconds to allow the thermocouple to heat up. The
burner may go out when the knob is released: in this case, the thermocouple
has not heated up sufficiently.
Wait a few moments and repeat the operation keeping the knob pressed for
longer.
If the burners should go out accidentally, a safety device will be tripped, cutting off the gas supply, even if
the gas tap is open. In this case, turn the knob to the OFF position and wait at least 60 seconds before
trying to light the burner again.
6.3 Practical hints for using the hob burners
For better burner efficiency and to minimise gas consumption: use pans with
lids and of a suitable size for the burner, so that the flames do not reach up
the sides of the pan (see paragraph “6.4 Pan diameters”). Once the contents
come to the boil, turn down the flame far enough to ensure that the liquid
does not boil over. If any liquid does boil over or spill, remove the excess
from the hob.
To prevent burns or damage to the hob during cooking, all pans or griddles
must be placed inside the perimeter of the hob. All pans must have smooth,
flat bottoms.
If the flame accidentally goes out, turn off the control knob and wait at
least 1 minute before trying to re-light the burner.
Take the greatest care when using fats or oils since they may catch fire if overheated.
13
Page 12
Instructions for the user
6.4 Pan diameters
Burner Ø min. (cm) Ø max. (cm)
Auxiliary 12 14
Semi-rapid 16 24
Ultra-rapid 18 26
To prevent damage to the appliance or adjacent units, all pans or griddles must be placed inside the
perimeter of the hob.
14
Page 13
Instructions for the user
7. USING THE OVEN
7.1 Before using the appliance
• Remove any labels (apart from the technical data plate) from trays, dripping pans and the cooking
compartment.
• Remove any protective film from the outside or inside of the appliance, including from accessories
such as trays, dripping pans, the pizza plate or the base cover.
• Before using the appliance for the first time, remove all accessories from the oven compartment and
wash them as indicated in “9. CLEANING AND MAINTENANCE”.
Heat the empty appliance to the maximum temperature in order to remove any manufacturing
residues which could affect the food with unpleasant odours.
7.2 Oven runners
The oven features 5 runners for positioning
trays and racks at different heights. The
insertion heights are indicated from the
bottom upwards (see figure).
models with frames models with guides
7.3 Storage compartment (on some models only)
The storage compartment is in the bottom of
the cooker. It provides storage space for the
appliance’s metal accessories and must not
be used to store flammable materials, cloths,
paper etc..
Do not open the storage compartment when the oven is on and still hot. The temperatures inside it may
be very high.
7.4 Cooling system
The appliance is equipped with a cooling system which comes into operation as soon as a cooking
function starts, with the exception of the gas burner where start-up is delayed. The fan causes a steady
outflow of air that exits from the rear of the appliance and which may continue for a brief period of time
even after the appliance has been turned off.
7.5 Internal light
The light inside the oven comes on when any function is selected, except when the bottom burner is
being used, in which case the timer knob must be turned to symbol .
15
Page 14
Instructions for the user
7.6 General warnings and advice for use
All cooking operations must be carried out with the door closed. The dissipation of heat may
cause hazards.
During cooking, do not cover the bottom of the oven with aluminium or tin foil and do not place pans or
oven trays on it as this may damage the enamel coating. If you wish to use greaseproof paper, place it so
that it will not interfere with the hot air circulation inside the oven.
For the best cooking results, we recommend placing cookware in the
centre of the rack.
To prevent any steam in the oven from causing problems, open the door in
two stages: keep it half open (5 cm approx.) for 4-5 seconds and then fully
open. To access food, always leave the door open as short a time as
possible to prevent the temperature in the oven from falling and ruining the
food.
To prevent excessive amounts of condensation from forming on the internal glass, hot food should not be
left inside the oven for too long after cooking.
While cooking desserts or vegetables, excessive condensation may form on the glass. In order
to avoid this, open the door very carefully a couple of times while cooking.
To prevent hazardous overheating, the appliance's lid (where present) must always be raised when using
the oven.
Heat the empty appliance to the maximum temperature in order to remove any manufacturing
residues which could affect the food with unpleasant odours.
16
Page 15
Instructions for the user
7.7 Using the bottom burner
7.7.1 Electronic spark ignition
Open the oven door fully, press the thermostat knob and turn it counterclockwise between MIN and
MAX; the electric spark ignition is activated automatically. After lighting, keep the knob pressed down for
a few seconds to allow the thermocouple to heat up. If the burner does not ignite after 15 seconds, stop
attempting to light it, leave the oven door open and do not try to light it again for at least 1 minute.
The bottom burner cannot be on while the door is closed.
7.7.2 Manual ignition
In the event of a power failure, the oven can be ignited manually. Open the
oven door fully, press and turn the thermostat knob anticlockwise between
MIN and MAX; light a long match and put the flame through the centre front
slots on the bottom of the oven (as indicated in the figure). Alternatively use
an electric gas lighter with a long spout. After lighting, keep the knob
pressed down for a few seconds to allow the thermocouple to heat up. If the
burner does not ignite after 15 seconds, stop attempting to light it, leave the
oven door open and do not try to light it again for at least 1 minute.
If the burner is extinguished accidentally, turn the knob to the off position (0) and wait at least one minute
before trying to light it again.
7.8 Using the electric grill
Use the function selection knob to select either the grill or the fan-assisted grill. For further information
see “8. COOKING WITH THE OVEN”.
Lighting the gas burner will switch off the electric grill element. The bottom burner and the
electric grill can never be used at the same time.
• Grilling processes must never last more than 60 minutes.
• Accessible parts may be very hot during and after use of the grill; keep children well away from the
appliance.
17
Page 16
Instructions for the user
8. COOKING WITH THE OVEN
GRILL:
The heat coming from the grill element gives perfect grilling results above all for thin
and medium thickness meat and in combination with the rotisserie (where present)
gives the food an even browning at the end of the cooking. Perfect for sausages, ribs
and bacon. This function enables large quantities of food, particularly meat, to be
grilled evenly. (4
FAN-ASSISTED GRILL:
The air produced by the fan softens the strong heatwave generated by the grill, giving
perfect grilling even to very thick foods. Perfect for large cuts of meat (e.g. shin of
pork). We recommend using the 4
FAN:
This function is useful for activating ventilation while using the bottom gas burner.
The air produced by the fan helps distribute heat evenly inside the oven.
DEFROSTING:
Rapid defrosting is helped by switching on the fan to ensure uniform distribution of air
inside the oven. (We recommend using the 1
th
or 5th runner).
th
runner.
st
or 2nd runner).
18
Page 17
Instructions for the user
8.1 Cooking advice and instructions
8.1.1 General advice
• We recommend preheating the oven before putting the food in. Place the food in the oven only
once the cooking light is off.
• For cooking on several levels, we recommend using a fan-assisted function to achieve uniform
cooking at all heights.
• In general, it is not possible to shorten the cooking times by increasing the temperature (the food
could be well-cooked on the outside and undercooked on the inside).
• While cooking desserts or vegetables, excessive condensation may form on the glass. In order to
avoid this, open the door very carefully a couple of times while cooking.
• For rapid preheating use a fan-assisted function, then select the required function.
8.1.2 Advice for cooking meat
• Cooking times, especially for meat, vary according to the thickness and quality of the food and to
consumer taste.
• We recommend using a meat thermometer for meat when roasting it. Alternatively, simply press on
the roast with a spoon: if it is hard it is ready, if not, it needs another few minutes cooking.
• •
• •
• •
• •
•
8.1.3 Advice for cooking desserts and biscuits
• Use dark metal moulds for desserts: they help to absorb the heat better.
•
• The temperature and the cooking time depend on the quality and consistency of the dough.
•
• Check whether the dessert is cooked right through: at the end of the cooking time, put a toothpick into
the highest point of the dessert. If the dough does not stick to the toothpick, the dessert is cooked.
•
• If the dessert collapses when it comes out of the oven, on the next occasion reduce the set
temperature by about 10°C, selecting a longer cooking time if necessary.
8.1.4 Advice for defrosting and proving
• We recommend positioning frozen foods in a lidless container on the first runner of the oven.
• •
• The food must be defrosted without its wrapping.
• •
• Lay out the foodstuffs to be defrosted evenly, not overlapping.
• •
• When defrosting meat, we recommend using a rack positioned on the second runner with the
food on it and a tray positioned on the first runner. In this way, the liquid from the defrosting food
drains away from the food.
• •
• The most delicate parts can be covered with aluminium foil.
• •
• For successful proving, a container of water should be placed in the bottom of the oven.
8.1.5 Advice for cooking with the Grill and the Fan-assisted grill
• Using the Grill function , meat can be grilled even when it is put into the oven cold; preheating is
recommended if you wish to change the effect of the cooking.
•
• With the Fan-assisted grill function , however, we recommend that you preheat the oven before
grilling.
19
Page 18
Instructions for the user
8.2 Cooking operation information table
Types of food Weight Function
FIRST COURSES
Runner
position
from the
bottom
Temperature
bottom burner
°C
Time
(minutes)
bottom burner +
Temperature
°C
Time
(minutes)
Lasagne 3 kg - 4 230 - 240 50 - 60 230 - 240 45 - 50
Cannelloni 2.5 Kg - 3 220 - 230 25 - 30 220 - 230 25 -30
Oven-baked pasta 2.5 Kg - 3 220 - 230 25 - 30 220 - 230 25 - 30
MEAT
Roast chicken 1.2 Kg - 3 200 - 210 80 - 90 200 - 210 75 - 80
Turkey breast
3 kg - 3 200 - 210 90 - 100 200 - 210 90 - 100
Pork loin 1.2 Kg - 3 210 - 220 70 - 75 200 - 210 90 - 100
Roast rabbit 1.5 kg - 3 200 - 210 75 - 80 200 - 210 75 - 80
Lamb 1.5 kg - 3 200 - 210 90 - 95 200 - 210 90 - 95
GRILLED MEATS
Pork chops 1 Kg
Hamburgers 1 Kg
Fan-ass.
Grill
4 - 15 8 - 15 8
5 - 11 7 - 11 7
1st side 2nd side 1st side 2nd side
Sausages 1.5 Grill 5 - 15 5 - 15 5
Spare ribs 1.5
Fan-ass.
5 - 15 5 - 15 5
Meat kebabs 1.5 Grill 5 - 11 10 - 11 5
FISH
Mackerel 8 Kg - 3 180 - 190 25 - 30 180 - 190 25 - 30
Salmon trout 1.3 Kg - 3 180 - 190 35 - 40 180 - 190 35 - 40
Turbot 1 Kg - 3 180 - 190 25 - 30 180 - 190 25 - 30
GRILLED FISH
Fish kebabs 1 Kg Grill 5 - 7 3 - 7 5
BREAD and FOCACCIA
Pizza 1 Kg - 3 240 12 - 15 240 12 - 15
Bread 1 Kg - 3 200 20 - 25 200 20 - 25
Focaccia 1 Kg - 3 200 20 - 25 180 20 - 25
DESSERTS
Short pastry biscuits 1 Kg - 2 190 18
Paradise cake
1 Kg - 2 190 50 - 55
Jam tart 1 Kg - 2 190 35 - 40
180
180
180
18
55 - 60
35 - 40
Ring cake 1.2 Kg - 2 190 15 - 50 180 50 -55
20
The times indicated in the following tables do not include the preheating times and are provided
as a guide only.
Page 19
Instructions for the user
9. CLEANING AND MAINTENANCE
Do not use steam jets for cleaning the appliance. The steam could reach the electronics,
damaging them and causing short-circuits.
WARNING: For your safety, you are advised to wear protective gloves while performing any
cleaning or extraordinary maintenance.
Do not use cleaning products containing chlorine, ammonia or bleach on steel parts or parts with
metallic finishes on the surface (e.g. anodizing, nickel- or chromium-plating).
We recommend the use of cleaning products distributed by the manufacturer.
9.1 Cleaning stainless steel
To keep stainless steel in good condition it should be cleaned regularly after use. Let it cool first.
9.2 Ordinary daily cleaning
To clean and preserve the stainless steel surfaces, always use only specific products that do not contain
abrasives or chlorine-based acids.
How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a
soft cloth or a microfibre cloth.
9.3 Food stains or residues
Do not use metallic sponges or sharp scrapers as they will damage the surfaces.
Use ordinary non-abrasive products with the aid of wooden or plastic utensils if necessary. Rinse
thoroughly and dry with a soft cloth or a microfibre cloth.
Do not allow residues of sugary foods (such as jam) to set inside the oven. If allowed to set for too long,
they could ruin the enamel covering the inside of the oven.
9.4 Cleaning the cooking hob parts
9.4.1 Pan stands
Remove the pan stands and clean them with lukewarm water and non-abrasive detergent, making sure
to remove any encrustations. Dry them thoroughly and return them to the hob.
Continuous contact between the pan stands and the flame can cause modifications to the enamel over
time in those parts exposed to heat. This is a completely natural phenomenon which has no effect on the
operation of this component.
Do no wash these parts in a dishwasher.
21
Page 20
Instructions for the user
9.4.2 Burner caps and flame-spreader crowns
The burner caps and flame-spreader crowns can be removed for easier
cleaning. Wash them in warm water and a non-abrasive detergent making
sure to remove any encrustation, then wait until they are perfectly dry.
Refit the flame-spreader crowns, making sure that they are correctly in
place with their respective burner caps, and ensuring that the holes A in
the flame-spreaders are aligned with the igniters and thermocouples.
Do no wash these parts in a dishwasher.
9.4.3 Igniters and thermocouples
For correct operation, the igniters and thermocouples must always be
perfectly clean. Check them frequently and clean them with a damp cloth if
necessary. Remove any dry residues with a wooden toothpick or a needle.
Do not use cleaning products containing chlorine, ammonia or bleach on steel parts or parts with
metallic finishes on the surface (e.g. anodizing, nickel- or chromium-plating).
9.5 Cleaning the oven
For the best oven upkeep, clean it regularly after having
allowed it to cool.
• Take out all removable parts.
• Clean the oven racks with hot water and non-abrasive
detergent. Rinse and dry.
• For easier cleaning, the door can be removed (see
“10.2 Removing the door”).
The oven should be operated at the maximum heat setting for 15/20 minutes after use of specific
products, to burn off the residues left inside the oven.
When the operation is complete, damp parts should be dried thoroughly.
22
Page 21
Instructions for the user
9.5.1 Removing guide frames (where present)
Removing the guide frames enables the sides to cleaned
more easily. This should be done each time the automatic
cleaning cycle is used (on some models only).
To remove the guide frames:
1 pull the frame towards the inside of the oven to unhook
it from its housing A.
2 Slide it out of the seats at the back B.
When cleaning is complete, repeat the above procedures
to put the guide frames back in.
9.5.2 Cleaning the door glazing
The glass in the door should always be kept thoroughly clean. Use absorbent kitchen roll; remove
stubborn dirt with a damp sponge and an ordinary detergent.
Do not use abrasive or corrosive detergents to clean the oven's glass doors (e.g. powder products, spotremovers and wire sponges). Do not use rough or abrasive materials or sharp metal scrapers to clean
the oven's glass doors since they may scratch the surface.
9.5.3 Cleaning the door seal
To keep the seal clean, use a non-abrasive sponge and lukewarm water. The seal should be soft and
flexible (with the exception of pyrolitic models).
In pyrolitic models, the seal may flatten over time and lose its original shape. To restore it, pinch the seal
all the way along. This also helps remove any dirt on the seal.
23
Page 22
Instructions for the user
10. EXTRAORDINARY MAINTENANCE
The oven requires periodic minor maintenance or replacement of parts subject to wear, such as gaskets,
light bulbs, etc. Specific instructions for each operation of this kind are given below.
Before any intervention that requires access to live parts, disconnect the appliance from the
power supply.
WARNING: For your safety, you are advised to wear protective gloves while performing any
cleaning or extraordinary maintenance.
10.1 Replacing the light bulb
If a light bulb needs to be replaced because it is worn
or burnt out, remove the guide frames; see “9.5.1
Removing guide frames (where present)”.
Then remove the bulb cover using a tool (e.g. a
screwdriver).
Remove the bulb by unscrewing (filament bulbs) or
pulling it (halogen bulbs) in the indicated direction.
Replace the bulb with one of the same type (25W for
filament bulbs or 40W for halogen bulbs).
Do not touch halogen bulbs directly with your fingers, wrap them in insulating material.
10.2 Removing the door
Open the door completely.
Insert a pintle into the hole in the
hinge. Repeat for both hinges.
Grasp the door on both sides
with both hands, lift it forming an
angle of around 30° and remove it.
To reassemble the door, put the
hinges in the relevant slots in the
oven, making sure that grooved
sections C are resting completely
at the base of the slots. Lower
the door and once it is in place
remove the pins from the holes in
the hinges.
24
Page 23
Instructions for the user
10.3 Removing the door seal (not on pyrolitic models)
To permit thorough cleaning of the oven, the door seal may be
removed.
There are fasteners on all four sides to attach it to the edge of
the oven. Pull the edges of the seal outwards to detach the
fasteners. The seal must be replaced when it loses elasticity
and hardens.
10.4 Removing the internal glass panels
The glass in the door should always be kept thoroughly clean. To facilitate cleaning, it is possible to
remove the door (see 10.2 Removing the door) and place it on a canvas, or open it and lock the hinges
in order to extract the glass panels. The glass panels of the door can be completely removed by following
the instructions provided below.
Warning: before removing the glass panels, make sure that at least one of the door's hinges has been
locked in the open position as described in chapter “10.2 Removing the door”. This operation may have
to be repeated during the glass removal process if the door is accidentally freed.
Removing the internal glass panel:
• Remove the internal glass panel by pulling the rear part
gently upwards, following the movement indicated by the
arrows (1).
• Then pull the front of the glass panel upwards (2).
• Doing this detaches the 4 pins attached to the glass from
their slots in the oven door.
Removing the middle glass panels:
• (pyrolitic models) there are two middle glass panels
attached using 4 small locks. Remove the middle panels by
lifting them upwards.
• (other models) an intermediate glass panel may be present;
if so, remove it by lifting it upwards.
Cleaning:
• It is now possible to clean the external glass panel and the
panels removed previously. Use absorbent kitchen roll. In
the case of stubborn dirt, wash with a damp sponge and
neutral detergent.
Replacing the glass panels:
• Replace the panels in the opposite order to which they were
removed.
• Reposition the internal glass panel, taking care to centre
and insert the 4 pins attached to the glass into their slots in
the oven door by applying slight pressure.
25
Page 24
Instructions for the installer
11. INSTALLATION
11.1 Installing in kitchen units
Veneers, adhesives or plastic coatings on adjacent furniture should be temperature-resistant (no less
than 90°C). If they are not sufficiently temperature-resistant, they may warp over time.
The appliance must be installed by a qualified technician and according to the standards in force.
Depending on the type of installation, this appliance belongs to class 2, subclass 1 (Fig. A - Fig. B) or
class 1 (Fig. C).
It may be installed next to walls, one of which must be higher than the appliance, at a minimum distance
of 50 mm from the side of the appliance, as shown in figures A and C relative to the installation classes.
Any wall units must be at a distance of at least 750 mm above the appliance. This distance can be
reduced to 650 mm if a ventilation hood is installed.
Built-in appliance
(Class 2 subclass 1)
Built-in appliance
(Class 2 subclass 1)
Free-standing appliance
(Class 1)
26
Page 25
Instructions for the installer
11.2 Room ventilation and combustion extraction
The room containing the appliance should be permanently ventilated in accordance with the standards
in force. The room where the appliance is installed must have enough air flow as required for the regular
combustion of gas and by the necessary air exchange of the same room. The air vents, protected by
grills, must be suitably dimensioned in compliance with current regulations and positioned so that no part
of them is obstructed.
The appliance must be kept adequately ventilated in order to eliminate the heat and humidity produced
by cooking: in particular, after prolonged use, you are recommended to open a window or to increase the
speed of any fans.
Combustion products can be extracted by means of hoods connected to a natural draught chimney
whose efficiency is assured or via forced extraction. An efficient extraction system requires precision
planning by a specialist qualified in this area and must comply with the positions and distances indicated
by the regulations. When the job is complete, the installer must issue a certificate of conformity.
Extraction using a hood.
Extraction without a hood.
Single natural draught chimney.
Single chimney with extractor
fan.
Directly outdoors with wall- or
window-mounted extractor fan.
Directly outdoors through wall.
Air
Combustion products
Extractor fan
27
Page 26
Instructions for the installer
11.3 Gas connection
At the end of the installation, check for any leaks with a soapy solution, never with a flame.
The tightening torque between connections that incorporate a gasket must be between 10 and 15 Nm.
After carrying out any operation on the appliance, check the gas connections are properly tightened.
If the appliance is fuelled by LPG, use a standards-compliant pressure regulator
and connect to the gas cylinder in accordance with the regulations in force.
Make sure that the feed pressure complies with the values indicated in the table
“12.5 Burner and nozzle characteristics table”.
11.3.1Connection with a rubber hose
WARNING: The following instructions are valid solely for Class 1 installations. See fig. C in
chapter “11.1 Installing in kitchen units”.
Connection using a rubber hose complying with the current regulations is only permitted if the hose can
be inspected along its entire length.
The inside diameter of the hose must be 8 mm for LPG GAS and 13 mm for NATURAL GAS and CITY
GAS.
Installation with a standards-compliant rubber hose must be carried out so that the
length of the piping does not exceed 1.5 metres; make sure that the hose does not
come into contact with moving parts and that it is not crushed in any way.
Verify that all the following conditions are met:
• the hose is fixed to the hose connection with safety clamps;
• no part of the hose is in contact with hot walls (max. 50°C);
• the hose is not under traction or tension and has no kinks or twists;
• the hose is not in contact with sharp objects or sharp corners;
• if the hose is not perfectly airtight and leaks gas, do not try to repair it: replace
it with a new hose;
• verify that the hose is not past its expiry date (serigraphed on the hose itself).
28
Page 27
Instructions for the installer
3
2
1
4
3
6
5
2
1
3
2
1
4
3
Make the connection to the gas mains using a rubber hose
whose specifications comply with the current regulations
(verify that the reference standard is stamped on the hose).
Carefully screw the hose connector 3 to the appliance’s gas
connector 1 (1/2” thread ISO 228-1), placing the seal 2
between them. The hose connector 4 can also be screwed to
the hose connector 3, depending on the diameter of the gas
pipe used. After having tightened the hose connector(s), push
the gas pipe 6 onto the hose connector and secure it with the
clamp 5 that is compliant with the applicable standard.
11.3.2Connection with a flexible steel hose
WARNING: The following instructions are valid for all types of installation, see fig. A, B, C in
chapter “11.1 Installing in kitchen units”.
Only use standards-compliant continuous wall steel hoses no longer than 2 metres.
This type of installation can be used for both built-in and free-standing appliances.
Make the connection to the gas mains using a continuous wall flexible steel pipe
whose specifications comply with the applicable standard.
Carefully screw the connector 3 to the appliance’s gas connector 1 (1/2” thread ISO
228-1), placing the seal 2 between them.
11.3.3Connection with a flexible steel hose with conical fitting (where present)
WARNING: The following instructions are valid for all types of installation, see fig. A, B, C in
chapter “11.1 Installing in kitchen units”.
Only use standards-compliant continuous wall steel hoses no longer than 2 metres.
This type of installation can be used for both built-in and free-standing appliances.
Make the connection to the gas mains using a continuous wall flexible steel pipe
whose specifications comply with the applicable standard.
Carefully screw the connector 3 to the appliance’s gas connector 1 (½” thread ISO
228-1), placing the seal 2 between them. Apply insulating material to the thread of
the connector 3, and then tighten the flexible steel pipe 4 to the connector 3.
29
Page 28
Instructions for the installer
11.4 Electrical connection
Make sure the voltage and the cross-section of the power supply line match the specifications indicated
on the identification plate positioned on the appliance. Do not remove this plate for any reason. A copy of
the plate is attached to the instructions.
The appliance must be connected to the power supply by a qualified technician.
Before performing any operations, switch off the power supply to the appliance.
The appliance must be connected to earth in compliance with electrical system safety regulations.
Where the appliance is connected to the power grid via a plug and socket, both of these must be of the
same type and connected to the power cable in accordance with the applicable regulations. The socket
must be accessible after the appliance has been built in.
NEVER UNPLUG BY PULLING ON THE CABLE.
Should the earthing wire need replacing it must be longer than the current conduction wires so that, if
the plug is torn off the power cable, it is the last to be detached.
Avoid use of adapters and shunts as these could cause overheating and risk of burns.
If a fixed connection is being used, fit the power line with an omnipolar circuit breaker with a contact
opening gap equal to or greater than 3 mm, in an easily accessible position close to the appliance.
The manufacturer declines all responsibility for damage to persons or things caused by nonobservance of the above prescriptions or by interference with any part of the appliance.
APPLIANCE
TYPE
(CM)
60
POSSIBLE CONNECTION
TYPES
220 - 240 V 1N~ 3-pole 3 x 1.5 mm² H05V2V2-F
appliance side
CABLE TYPE
(if not present)
30
• Use H05V2V2-F cables resistant to at least 90°C.
• The values indicated above refer to the cross-section of the internal conductor.
• The tightening torque of the screws of the terminal supply wires must be 1.5 - 2 Nm.
• The aforementioned power cables are sized taking into account the coincidence factor (in compliance
with standard EN 60335-2-6).
Page 29
Instructions for the installer
11.5 Positioning the skirt (on some models only)
The skirt must always be positioned and secured correctly on
the appliance.
1 Loosen the 4 screws (A) on the back of the worktop (2 for
each side).
2 Place the skirt above the worktop, taking care to align the
skirt's slots (B) with the screws (A).
3 Secure the skirt to the worktop by tightening screws (A).
11.6 Positioning and levelling the appliance
After making the electrical and/or gas connections, level the
appliance on the floor by means of its four adjustable feet.
First insert the front feet and then the rear feet.
The appliance must be properly levelled to ensure better
stability. Screw or unscrew the bottom part of the foot until
the appliance is stable and level on the floor.
To prevent possible damage to the appliance, we recommend to screw first the front feet and then the
rear ones.
31
Page 30
Instructions for the installer
B
A
12. ADAPTATION TO DIFFERENT TYPES OF GAS
BEFORE PERFORMING ANY OPERATIONS, SWITCH OFF THE POWER SUPPLY TO THE
APPLIANCE.
Appliance set for gas: NATURAL G20 (2H) pressure 20 mbar (see label on product)
In the case of operation with other types of gas, the burner nozzles must be changed and the minimum
flame adjusted on the gas taps.
To change the nozzles, proceed as described in the following paragraphs.
12.1 Replacement of nozzles on the hob
1 Remove the pan stands and remove all the burner caps
and flame-spreader crowns to access the burner
casings.
2 Unscrew the nozzles using a 7 mm socket wrench.
3 Replace the burner nozzles according to the type of gas
to be used (see 12.5 Burner and nozzle characteristics
table).
4 Replace the burners in the correct position.
12.2 Replacing the bottom burner's nozzle
1 Remove all accessories from inside the oven (such as
trays, racks etc.).
2 Lift up the oven surface and pull it outwards as shown in
the figure.
3 Unscrew the fastening screws A and B completely.
4 Move away the lock that secures the thermocouple and
igniter fastened by screw A.
5 Slide the burner outwards until the nozzle is accessible.
6 Using a 7mm socket wrench, replace the nozzle,
inserting a new nozzle suitable for the type of gas to be
used (see “12.5 Burner and nozzle characteristics
table”).
32
Page 31
Instructions for the installer
12.3 Arrangement of burners
Burner
Auxiliary
Semi-rapid
Ultra-rapid
12.4 Final operations
After replacing the nozzles, reposition the flame-spreader crowns, the burner caps and the pan stands.
Following adjustment to a gas other than the one originally set in the factory, replace the gas setting
label fixed to the appliance with the one corresponding to the new gas. The label is inserted inside the
nozzle pack (where present).
12.4.1Adjusting the hob burner minimum setting for city or natural gas
Light the burner and turn it to the minimum position.
Extract the gas tap knob and turn the adjustment screw
next to the tap rod (depending on the model) until the
correct minimum flame is achieved. Refit the knob and
verify that the burner flame is stable (when turning the
knob rapidly from the maximum to the minimum position
the flame must not go out). Repeat the operation on all
the gas taps.
12.4.2Adjusting the hob burner minimum setting for LPG
In order to adjust the minimum setting with LPG, the screw at the side of the tap rod must be tightened
clockwise all the way.
33
Page 32
Instructions for the installer
12.4.3Adjusting the gas oven burner minimum setting
1 Light the oven burner and keep it at the maximum for 10/15 minutes.
2 Then turn the knob to the minimum temperature.
3 Extract the gas tap knob and turn the adjustment screw next to the tap rod
(depending on the model) until the correct minimum flame is achieved.
4 Refit the knob and verify that the burner flame is stable (when turning the
knob rapidly from the maximum to the minimum position the flame must not
go out). This procedure must be carried out while the door is closed.
5 (Only for adjustment different from LPG) Open and close the door, if the flame
goes out the minimum must be increased.
If using LPG, the adjustment screw must be tightened to end of stroke. If using city gas or natural gas,
simply unscrew the adjustment screw by a few turns.
12.5 Burner and nozzle characteristics table
Burner
Auxiliary 1.05 50 400 76 75
Semi-rapid 1.8 65 500 131 129
Ultra-rapid 3.9 100 1600 283 278
Oven 2.6 76 900 189 186
Burner
Auxiliary 1.05 72 (X) 400
Semi-rapid 1.8 97 (Z) 500
Ultra-rapid 3.9 135 (K) 1600
Oven 2.6 120 - 900
Rated heating
capacity (kW)
Rated heating
capacity (kW)
Nozzle
diameter
(1/100 mm)
Nozzle
diameter
(1/100 mm)
LPG GAS - G30/G31 28-30/37 mbar
Reduced
capacity (W)
NATURAL GAS - G20 20 mbar
Prechamber
(printed on
nozzle)
Capacity
(g/h G30)
Reduced capacity
(W)
Capacity
(g/h G31)
34
Loading...