Table of contents
1. INSTRUCTIONS FOR USE.............................................. 4
2. SAFETY INSTRUCTIONS................................................ 5
3. INSTRUCTIONS FOR DISPOSAL – OUR
ENVIRONMENTAL CARE................................................ 6
4. GET TO KNOW YOUR OVEN .......................................... 7
5. BEFORE INSTALLATION................................................. 7
6. AVAILABLE ACCESSORIES ............................................ 8
7. USING THE OVEN ........................................................... 9
8. COOKING WITH THE OVEN ......................................... 20
9. CLEANING AND MAINTENANCE.................................. 29
10. EXTRAORDINARY MAINTENANCE .............................. 31
11. INSTALLING THE APPLIANCE...................................... 35
INSTRUCTIONS FOR THE USER: these specify usage
recommendations, and describe the commands and the correct
cleaning and maintenance operations for the appliance
INSTRUCTIONS FOR THE INSTALLER: these are intended for the
qualified technician who will carry out the installation, operation and
testing of the appliance
3
General instructions
1. INSTRUCTIONS FOR USE
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST BE KEPT
IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE
WORKING LIFE OF THE OVEN.
CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS
THEREIN BEFORE USING THE APPLIANCE IS ESSENTIAL. INSTALLATION
MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH
THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR
HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY
IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE
FOLLOWING FUNCTIONS: COOKING AND HEATING FOODS; ALL OTHER
USES ARE TO BE CONSIDERED IMPROPER. THE MANUFACTURER
DECLINES ALL RESPONSIBILITY FOR IMPROPER USE.
DO NOT USE THIS APPLIANCE FOR HEATING ROOMS.
THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE
2002/96/CE ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT –
(WEEE).
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF
RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT.
DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT DISPERSAL SLITS.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT
IS INOPERATION.
THIS APPLIANCE IS DESIGNED FOR COOKING FOOD AND IT SHALL NOT BE
USED AS A SPACE HEATER.
THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND
BRAND NAME IS POSITIONED VISIBLY ON THE OVEN DOOR FRAME.
THE PLATE MUST NOT BE REMOVED.
DO NOT USE METALLIC SPONGES OR SHARP SCRAPERS: THEY
WILL DAMAGE THE SURFACE.
USE ORDINARY NON-ABRASIVE PRODUCTS WITH THE AID OF
WOODEN OR PLASTIC UTENSILS IF NECESSARY. RINSE
THOROUGHLY AND DRY WITH A SOFT CLOTH OR CHAMOIS
LEATHER.
DO NOT ALLOW RESIDUES OF SUGARY FOODS (SUCH AS JAM) TO
SET INSIDE THE OVEN. IF LEFT TO SET FOR TOO LONG, THEY
MIGHT DAMAGE THE ENAMEL LINING OF THE OVEN.
4
General instructions
2. SAFETY INSTRUCTIONS
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE SAFETY
REGULATIONS FOR ELECTRIC OR GAS APPLIANCES AND VENTILATION
FUNCTIONS.
IN YOUR INTERESTS AND FOR YOUR SAFETY IT HAS BEEN ESTABLISHED
BY LAW THAT THE INSTALLATION AND SERVICING OF ALL ELECTRICAL
APPLIANCES IS TO BE CARRIED OUT BY QUALIFIED PERSONNEL IN
ACCORDANCE WITH THE REGULATIONS IN FORCE.
OUR REGULAR INSTALLERS GUARANTEE A SATISFACTORY JOB.
GAS OR ELECTRIC APPLIANCES MUST ALWAYS BE DISCONNECTED BY
SUITABLY SKILLED PEOPLE.
THE PLUG TO BE CONNECTED TO THE POWER CORD AND ITS SOCKET
MUST BE OF THE SAME TYPE AND CONFORM TO THE REGULATIONS IN
FORCE.
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE IS BUILT IN.
NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY
LEAD.
IT IS OBLIGATORY FOR ALL ELECTRICAL SYSTEMS TO BE GROUNDED
ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST,
FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT
FUNCTION, DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST
TECHNICAL ASSISTANCE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.
NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE
ACCIDENTALLY LIGHTED AND CAUSE FIRES.
DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO
TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.
THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING
CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN
EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY ARE
SUPERVISED OR INSTRUCTED BY ADULTS OR PEOPLE RESPONSIBLE FOR
THEIR SAFETY.
BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE PROTECTIVE
FILMS APPLIED ON THE OUTSIDE MUST BE REMOVED.
The manufacturer declines all responsibility for damage to persons or things
caused by non-observance of the above prescriptions or by interference with
any part of the appliance or by the use of non-original spares.
5
Instructions for disposal
3. INSTRUCTIONS FOR DISPOSAL – OUR ENVIRONMENTAL CARE
Our product's packing is made of non-polluting materials, therefore
compatible with the environment and recycable. Please help by disposing
of the packing correctly. Find the addresses of collection, recycling and
disposal centres from your retailer or from the competent local
organisations.
Do not throw the packing or any part of it away. They can constitute a
suffocation hazard for children, especially the plastic bags.
Your old appliance also needs to be disposed of correctly.
Important: Hand over your appliance to the local agency authorised for
the collection of electrical appliances no longer in use. Correct disposal
means intelligent recycling of valuable materials.
Before disposing of your old appliance remove the door and leave the
racks in their normal working positions so that children cannot get stuck in
the oven compartment whilst playing. It is also necessary to cut the
electric power cord and remove it along with the plug.
DO NOT DISCARD PACKING IN THE HOME ENVIRONMENT. SEPARATE THE
VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL
GARBAGE COLLECTION CENTRE.
6
Instructions for the user
4. GET TO KNOW YOUR OVEN
Control panel
Roof liner
Oven light
Shelf and tray
runners
Temperature sensor
Oven fan
Oven door
5. BEFORE INSTALLATION
In order to remove all manufacturing residues, it is recommended to clean
the inside of the appliance. For further information on cleaning see
paragraph "9. CLEANING AND MAINTENANCE".
Before using the oven for the first time, pre-heat it to maximum
temperature long enough to burn any manufacturing oily residues which
could give the food a bad taste. The Turbo function is recommended for
this purpose
.
7
Instructions for the user
6. AVAILABLE ACCESSORIES
Grill: useful for holding cooking containers.
Tray g r i d: for placing on top of a tray for cooking
foods which may drip.
Oven tray: useful for collecting fat from foods placed
on the grid above.
Pastry plate (on some models only): for baking
cakes, pizza and oven desserts.
Chromium-plated gripper: use to remove hot oven
racks and pans.
Roasting spit: used for roasting chicken, sausages
and anything else requiring uniform browning.
Rotisserie frame: fits into the slots of the oven pan
prior to attaching the rotisserie rod.
(see page 28 for instructions for use)
Roof liner: remove it to simplify cleaning
inside the oven.
Accessories available on request:
Original supplied and optional accessories may be ordered from any
Authorised Service Centre.
8
Instructions for the user
7. USING THE OVEN
7.1 General Description
7.1.1 Oven racks
The oven features 4 runners for positioning trays
and grills at different heights. The insertions
heights are numbered from the bottom upwards
(see figure).
(When using the recipes, the display will show the
recommended runner for the selected recipe).
7.1.2 Cooling system
The appliance is equipped with a cooling system which comes into
operation as soon as a cooking function starts. The fan cause a steady
outflow of air from above the door which may continue for a brief period of
time even after the oven has been turned off.
7.1.3 Inside light
The oven light comes on when the door is opened or any function or
recipe is selected.
7.2 Warnings and general advice for usage
All cooking operations must be carried out with the door closed.
During cooking, do not cover the bottom of the oven with aluminium or tin
foil and do not place pans or oven trays on it as these may damage the
enamel coating. If you wish to use greaseproof paper, place it so that it will
not interfere with the hot air circulation inside the oven.
To prevent any steam in the oven creating
problems, open the door in two stages: half open (5
cm approx.) for 4-5 seconds and then fully open. To
access food, always leave the door open as short a
time as possible to prevent the temperature in the
oven from falling and ruining the food.
To prevent excessive amounts of condensation from forming on the
internal glass, food should not be left inside the oven for too long after
cooking.
9
Instructions for the user
7.3 Description of the controls on the front panel
All the appliance's control and monitoring devices are placed together on
the front panel. The symbols used are described in the table below.
FUNCTIONS AND SYMBOLS SHOWN:
PT1
PT2
DSP1
cooking procedures
Recommended runner:
Thermostat
Programmed
Delayed start:
Cooking duration:
Functions
Knob
Functions
ON-OFF
Knob
Display
current
time
Clock:
Bell:
allows you to set the time, select the cooking
temperature and duration and program the
cooking start and end times.
allows access to the oven's three operating
modes, and is also used to select a cooking
function or cooking program
(see paragraph “7.4 Operating modes”).
This display shows the current time or the
cooking duration.
The following symbols coming on indicate:
adjusting the cooking time
minute minder activated.
setting the cooking time with a delayed start.
setting the cooking time.
recommended runner number according to
the selected cooking recipe.
Selectable functions
10
Instructions for the user
Temperature
Display
DSP2
Recommended runner:
Temperature inside the
Child lock-out function:
Showroom indicator light:
Recipe storing:
oven:
This display shows the preset temperature
for the function required, or the temperature
set by the user.
The following symbols coming on indicate:
recommended runner number according to
the selected cooking recipe.
The oven is heating up.
Child lock-out function mode ON (see
“Secondary menu” at page 19).
showroom mode ON (see “Secondary menu”
at page 19).
when flashing it indicates the modification
phase of the selected recipe.
Selectable
recipes
11
Instructions for the user
7.4 Operating modes
This appliance is programmed to provide 3 operating settings, which can
be modified by pressing PT2.
STAND-BY setting: with DSP1 on and
showing the current time (activated as
soon as the current time has been
confirmed).
ON setting: from the stand-by setting,
press PT2 once. All the displays and
knobs light up.
OFF setting: from the ON position,
keep PT2 pressed down until it
switches off. Only the symbol on
DSP1 remains on.
7.5 First use
At first use, or after a power failure, the oven's left hand-display, DSP1, will
show a flashing symbol . To start any cooking operation, the current
time must be set.
7.5.1 Setting the current time
Adjusting the current time
• turn PT1 to the right and left to increase or decrease the hours. (If the
knob is held in one direction the time changes faster).
• when PT1 is released, after a few seconds the display will stabilise and
only the two dots that separate the hours from the minutes will flash,
indicating it is working properly. (The display will also show the symbol
).
It might become necessary to change the current time, for example at the
switch from summer to winter time. Starting from the stand-by setting, (see
paragraph "7.4 Operating modes"):
• hold down PT1 for a few seconds until the symbol stops flashing.
• repeat the operations described in paragraph “7.5.1 Setting the current
time”.
12
7.6 Selecting a function
In the ON state only, a cooking function can be selected by simply turning
PT2 to the right or left. The function selected will change colour to red on
the display. After the selection, the preset cooking temperature will be
displayed on DSP2.
Instructions for the user
7.6.1 Cooking with preset temperature
After selection of the function required, the oven will start the cooking
procedure at the preset temperature and the symbol will come on.
Cooking itself is preceeded by a preheating stage, which allows the oven
to heat to the cooking temperature more quickly. The symbol flashes
on DSP2 to indicate that this stage is in progress. When the preheating
stage is over, the symbol will remain constantly on and a buzzer will
sound to indicate that the food can be placed inside the oven.
On the pyrolithic models, the special defrosting and proving functions are together
in the same symbol . Set the temperature to choose the function: thawing (30°C)
or proving (40°C). On the multifunction models, it is not possible to vary the
temperature in the defrosting and proving functions.
7.6.2 Changing the preset temperature
The temperature preset for each function can be changed to suit the user's
requirements.
At any time while cooking is in progress, turn PT1 in either direction to
increase or decrease the cooking temperature by 5 degrees at a time.
(PT1 can also be held in the left or right position to increase or decrease
the setting more quickly.)
7.6.3 Using the minute minder
Press PT1 once (either in the STAND-BY or ON mode). The display will
show the figures (constantly on) and the symbol (flashing). Turn
PT1 to set the minutes of cooking (from 00:01 to 04:00:00). A few seconds
after the required duration is set, the symbol will stop flashing and stay
on constantly; the countdown will start from that moment. Now select the
cooking function required and wait for the buzzer to sound, indicating that
the cooking time is over.
Press PT1 once to switch off the buzzer; extended cooking time can be set
by turning PT1.
If the minute minder was set in STAND-BY mode, when the oven is activated in ON
mode (selection of a cooking operation), the counter is reset to zero.
Warning: the minute minder does not stop the cooking process. It only warns the
user that the preset number of minutes have passed. To switch the oven off, press
PT2.
Modifying the data set
After setting the countdown, press PT1 once. The symbol starts
flashing; turn PT1 to change the set duration. A few seconds after the last
change, the symbol will stop flashing, and the countdown will restart
from the new value.
13
Instructions for the user
7.7 Programmed cooking procedures
7.7.1 Semiautomatic cooking
Semiautomatic cooking is the function which allows a cooking operation to
be started and then ended after a specific length of time set by the user.
Select a function (see paragraph “7.6 Selecting a function”) and press PT1
twice. The display will show the figures and the symbol
(flashing).
Turn PT1 to the right or left to set the minutes of cooking (from 00:01 to
23:59). A few seconds after the required duration is set, the symbol will
stop flashing, and semiautomatic cooking will start from that moment. At
the end, the word STOP will appear on DSP1, cooking will stop and a
buzzer will sound; press PT1 to deactivate it.
If you wish to continue cooking beyond the set time, press PT1 again. The oven will
restart normal operation with the cooking settings selected previously. PT2 has to
be pressed to switch the oven off completely.
Modifying the data set
Once semiautomatic cooking has started, its duration can be changed.
When the symbol is steady and cooking is in progress, press PT1
once. The symbol starts flashing and PT1 can be turned to change the
set duration. A few seconds after the last change, the symbol will stop
flashing, and semiautomatic cooking will restart from the new value.
To change the preset temperature, wait for the symbol to become
steady and turn PT1 to the right or left to increase or decrease the cooking
temperature.
7.7.2 Automatic cooking
14
Automatic cooking is the function which allows a cooking operation to be started at
a set time and then ended after a specific length of time set by the user.
Select a cooking function, set the cooking temperature required or leave
the preset temperature (see paragraph “7.6 Selecting a function”) and
press PT1 twice. The display will show the figures and the
symbol (flashing).
Turn PT1 to the right or left to set the minutes of cooking (from 00:01 to
23:59).
For safety reasons, when setting automatic cooking the user must first
program a cooking duration and then set the cooking start time. It is not
possible to set the cooking start time only, without setting the cooking
duration.
Instructions for the user
After setting the duration, press PT1 once.
The symbol and the current time will appear on the display.
Turning PT1 to the right increases the time, allowing the cooking start
time required to be set.
A few seconds after the required duration is set, the and symbols
will stop flashing, and the oven will start to wait for the starting time set. At
the end, the word STOP will appear on DSP1, cooking will stop and a
buzzer will sound; press PT1 once to deactivate it.
If you wish to continue cooking beyond the set time, press PT1 again. The oven will
restart normal operation with the temperature settings selected previously.
PT2 has to be pressed to switch the oven off completely.
Modifying the data set
Once automatic cooking has started, its duration can be changed.
When the and symbols are steady and cooking is in progress, or
the oven is in stand-by status waiting for cooking to start, press PT1 once.
The symbol starts flashing and PT1 can be turned to change the set
duration.
Press PT1 again; the symbol goes out, the symbol will start to
flash, and the cooking start time will be displayed on DSP1. The cooking
start time can be increased or decreased by turning PT1.
A few seconds after the last change, the and symbols will appear
(in steady mode) on DSP1 and automatic cooking will restart with the new
settings.
Once cooking has been programmed, before it starts, the function or recipe symbol
will remain on, as will the symbols
, .
15
Instructions for the user
7.8 Selecting a recipe
The oven has 9 preset recipes and 3 memories; a recipe is a set of
function, temperature and cooking times presettings.
In the ON state only, a recipe can be selected by simply turning PT2 to the
right or left. The recipe selected will change colour to red on the display.
Cooking will start with the preset parameters (symbols on). When
the preset temperature is reached, a series of beeps will be emitted
indicating that the oven is ready for use. The cooking time as specified in
the table “7.9 Table of predefined recipes:”starts from this moment.
7.8.1 Modifying the data set (during cooking)
During the cooking it is possible to modify preset temperature turning
PT1 to the right of left. To modify the duration press PT1 and turn it to
increase or decrease the value.
The modification operations to the data set must be carried out when both the
symbols
7.8.2 Automatic cooking with a recipe
To set automatic cooking, select a recipe and follow the instructions
described in paragraph “Automatic cooking” at page 14.
The use of this function is recommended in cooking operations that require a preheated oven, such as pizzas and cakes.
, are steady on.
16
Instructions for the user
7.8.3 Selecting a recipe permanently
The oven has 9 preset recipes (see “Table of predefined recipes:” at
page 18), and 3 to set according to your own named cooking preferences
. In addition, you can modify the other recipes that are already
preset.
To modify or set a recipe permanently:
1 From ON status, select the recipe to modify with PT2. Within 5
seconds of the selection, hold down PT1 for at least 2 seconds. The
symbol flashes indicating the recipe modification phase.
2 Now, by turning PT1, you can modify the cooking function to associate
to the recipe being modified. Press PT1 to confirm.
3 Setting the temperature. The preset temperature will be displayed on
DSP2 flashing; press PT1 to modify it. Press PT1 to confirm.
4 Modifying the cooking duration. The preset cooking duration will be
displayed on DSP1 flashing. Turning PT1 you can modify it. Press PT1
to confirm.
5 Modifying the recommended runner. The recommended runner will
flash; turning PT1 you can modify the number. Press PT1 to exit the
programming, the symbol will stop flashing.
17
Instructions for the user
7.9 Table of predefined recipes:
Class Typ e Qty. Temp.
0.7 Kg 200 30
Beef Roast-beef
Pork Roast
Chicken Roast chicken
Lamb Roast leg of lamb
Fish Bass baked in foil
Vegetables Stuffed peppers
Pizza Pizza pie 1 pizza 280 8*
1 Kg 200 40
1.5 Kg 200 65
0.5 Kg 180 50
1 Kg 190 85
1.5 Kg 180 110
0.5 Kg 190 40
1 Kg 190 60
2 Kg 180 90
1.0 Kg 190 65
1.5 Kg 180 100
0.7 Kg 200 35
1.0 Kg 200 45
1 Kg 170 45
1.5 Kg 160 50
2 Kg 160 60
(°C)
Cooking
duration
(min.)
Funct. Runner
Cakes Apple pie 8 people 180 65
Biscuits Lemon biscuits 1 tray 180 20
The cooking times specified in the table refer to the food indicated in the recipe;
they are approximate and may vary depending on the weight.
The table gives the factory-set data. To reset a recipe with the original settings after
it has been modified, just enter the data given in the table.
If the PO limiter mode is activated (see secondary menu) the cooking times can
vary from those indicated.
18
Instructions for the user
7.10 Secondary menu
This appliance also has a concealed "secondary menu" allowing the user
to:
1 Activate or deactivate the child safety device 2 Activate or deactivate the Showroom mode (which disables all the
heating elements so that only the control panel works).
3 Activate or deactivate the mode which limits the maximum power
absorption to 2300 W.
In OFF status (see "7.4 Operating modes") hold down PT1 for at least 2
seconds to display the seconday menu. Turning PT1 to the right or left
changes the setting status (ON / OFF).
Press PT1 to move on to setting of the next function.
Child lock-out mode: activating this mode
after two minutes of operation without any
intervention from the user the controls will
automatically be locked, indicated by the
coming on of the symbol . To disconnect
the temporary lock during cooking, hold
down PT1 for at least 5 seconds. Two
minutes after the last setting the lock will
become active again.
If a knob is turned “bloc” appears for
2 seconds.
Showroom mode: (only for exhibitors)
activating this mode disables all the heating
elements so that only the control panel
works (some models display the symbol
). To use the oven normally, set this mode
to OFF.
Power limiter mode: by selecting LO while
cooking with the main oven a limited
amount of power will be used, according to
the model. To reset the product's normal
consumption, select HI.
PO-HI = max 3kW
PO-LO= max 2,3 kW
19
Instructions for the user
8. COOKING WITH THE OVEN
ECO:
Using the grill and the bottom heating element plus
the fan is particularly suitable for cooking small
quantities of food, as it provides low energy
consumption.
STATIC:
As the heat comes from above and below at the
same time, this system is particularly suitable for
certain types of food. Traditional cooking, also known
as static or thermal radiation cooking, is suitable for cooking just one
dish at a time. Perfect for all types of roasts, bread, and tarts and in
any case particularly suitable for fatty meats such as goose and duck.
GRILL:
the heat coming from the grill element gives perfect
grilling results above all for thin and medium
thickness meat and in combination with the rotisserie
(where fitted) allows to give the food an even browning at the end of
the cooking. Perfect for sausages, ribs and bacon. This function
allows to grill large quantities of food, particularly meat, evenly.
20
ROTISSERIE GRILL:
The rotisserie functions in combination with the grill element,
browning food perfectly.
BOTTOM:
the heat coming just from the bottom allows to
complete the cooking of foods that require a longer
basic cooking time, without affecting their browning.
Perfect for cakes, pies, tarts and pizzas.
BOTTOM + CIRCULAR VENTILATED:
ventilated cooking is combined with the heat coming
from the bottom, at the same giving time slight
browning. Perfect for any type of food.
Instructions for the user
VENTILATED STATIC:
The operation of the fan combined with traditional
cooking, ensures uniform cooking even with complex
recipes. Perfect for biscuits and cakes, even when
simultaneously cooked on several levels.
VENTILATED GRILL:
The air produced by the fan softens the strong
heatwave generated by the grill, giving perfect grilling
even on very thick foods. Perfect for large cuts of
meat (e.g. shin of pork).
VENTILATED BOTTOM:
The combination of the fan with just the bottom
heating element allows cooking to be completed
more rapidly. This system is recommended for
sterilizing or for finishing off the cooking of foods already well-cooked
on the surface, but not inside, which therefore need a little more heat.
Perfect for any type of food.
CIRCULAR:
The combination of the fan and the circular element
(incorporated in the rear of the oven) allows to cook
different foods on several levels, as long as they need
the same temperatures and cooking time. Air circulation ensures
instant and uniform distribution of heat. It will be possible, for
instance, to cook fish, vegetables and biscuits simultaneously with
any smells and flavours mixing.
TURBO
The combination of ventilated cooking and
traditional cooking allows to cook different foods on
several levels extremely quickly and efficiently.
Perfect for large volumes that call for intense cooking.
21
Instructions for the user
THAWING:
Rapid thawing is helped by switching on the fan
provided and the top heating element that ensure
uniform distribution of low temperature air inside the
oven.
In the pyrolithic models this function integrates the proving. The
choice to thaw or to prove depends on the temperature selected. Set
the temperature to choose the function: thawing (30°C) or proving
(40°C).
PROVING:
The proving helped by the heat coming from the top
allows all types of dough to be proved, guaranteeing
perfect results quickly.
22
Instructions for the user
8.1 COOKING HINTS AND TIPS
HINTS ON USING THE ACCESSORIES:
• Use only SMEG original trays.
• When the tray is in the oven, the handle must be facing
the oven door.
• Push the trays right inside the oven.
• Use only SMEG original racks.
• When the rack is in the oven, the contoured part must be
facing downwards.
• Push the racks right inside the oven.
• For best cooking results, we recommend placing
kitchenware in the centre of the rack.
GENERAL HINTS:
• We recommend preheating the oven before putting
the food in. Do not place the foods inside the oven until
the degrees symbol on the display stops flashing and
the beep has sounded to confirm that the set temperature
has been reached.
• For cooking on several levels, we recommend using a
ventilated function to achieve uniform cooking at all
heights.
• In general, it is not possible to shorten the cooking times
by increasing the temperature (the food could be wellcooked on the outside and undercooked on the inside).
• During the cooking of desserts and vegetables, dripping
from the bottom of the door could occur. This is a natural
physical phenomenon which mainly occurs when the food
is placed in the oven before preheating. To avoid this,
open the door a couple of times during the cooking taking
great care.
23
Instructions for the user
COOKING HINTS FOR MEAT:
• Cooking times, especially meat, vary according to the
thickness and quality of the food and to consumer taste.
• To save energy when roasting, we recommend putting
the food in the cold oven.
• We recommend using a meat thermometer for meat
when roasting it. Alternatively, simply press on the roast
with a spoon: if it is hard it is ready, if not, it needs another
few minutes cooking.
COOKING HINTS FOR DESSERTS AND BISCUITS:
• Use dark metal moulds for desserts: they help to absorb
the heat better.
• The temperature and the cooking duration depend on the
quality and consistency of the dough.
• The tables indicate the temperature ranges. Initially, try
with the lowest value (the lower temperature gives a more
even browning); if the dessert does not come out well,
increase the temperature on the following occasions.
• Check whether the dessert is cooked right through: About
10 minutes before the end of cooking, stick a toothpick
into the highest point in the dessert. If the dough does not
stick to the toothpick, the dessert is cooked.
• If the dessert goes flat when it comes out of the oven, on
the next occasion reduce the set temperature by about 10
°C selecting a longer cooking time if necessary.
24
Instructions for the user
HINTS FOR THAWING AND PROVING:
• We recommend positioning frozen foods in a lidless
container on the first runner of the oven.
• The food must be thawed without its wrapping.
• Lay out the foodstuffs to be thawed evenly, not
overlapping.
• When thawing meat, we recommend using a rack
positioned on the second runner with the food on it and a
tray positioned on the first runner. In this way, the liquid
from the thawing food drains away from the food.
• The most delicate parts can be covered with aluminium
foil.
• For successful proving, a container of water should be
placed in the bottom of the oven.
• During proving it is recommended to cover the food with a
damp canvas.
25
Instructions for the user
8.2 Cooking tables:
The times indicated in the following tables do not include the preheating
times and are approximate. Always make sure to pre-heat and to load the
oven when the stays steady on.
FUNCTION
LEVEL
FROM
BELOW
FIRST COURSES
LASAGNE static 1 220 - 230 50 - 60
OVEN-BAKED PASTA static 1 220 - 230 40
MEAT
ROAST VEAL Ventilated static 2 180 - 190 70 - 80
LOIN OF PORK Ventilated static 2 180 - 190 70 - 80
SHOULDER OF PORK Tu r bo 2 180 - 190 90 - 100
ROAST RABBIT circular 2 180 - 190 70 - 80
TURKEY BREAST ventilated static 2 180 - 190 110 - 120
ROAST NECK OF PORK Tu r b o 2 180 - 190 190 - 210
TEMPERATURE
°C
TIME IN MINUTES
ROAST CHICKEN Tu r bo 2 180 - 190 60 - 70
FIRST
GRILLED MEATS
SURFACE
SECOND
SURFACE
PORK CHOPS Ventilated grill 4 300 7 - 9 5 - 7
FILLET OF PORK Grill 3 300 9 - 11 5 - 9
FILLET OF BEEF Grill 3 300 9 - 11 9 - 11
LIVER Ventilated grill 4 300 2 - 3 2 - 3
SAUSAGES Ventilated grill 3 300 7 - 9 5 - 6
MEAT-BALLS Grill 3 300 7 - 9 5 - 6
ROTISSERIE MEATS
On a
CHICKEN Rotisserie grill
rotisserie
250 - 280 60 - 70
rod
26
Instructions for the user
FISH
Bottom –
SALMON TROUT
PIZZA Ventilated static 1 250 - 280 6 - 10
BREAD Circular 2 190 - 200 25 - 30
MUFFINS Tu r bo 2 180 - 190 15 - 20
DESSERTS
DOUGHNUT Ventilated static 2 160 55 - 60
FRUIT TART Ventilated static 2 160 30 - 35
SHORT PASTRY
JAM TARTS Tu r bo 2 160 20 - 25
PARADISE CAKE Ventilated static 2 160 55 - 60
ECLAIR Tu r bo 2 150 - 160 40 - 50
ventilated
circular
Bottom +
ventilated
circular
2 150 - 160 35 - 40
2 160 - 170 20 - 25
LIGHT SPONGE CAKE Circular 2 150 - 160 45 - 50
RICE PUDDING Tu r b o 2 160 40 - 50
CROISSANTS Circular 2 160 25 - 30
8.3 Using other functions
The following tables indicate how to use the functions for thawing, proving
and cooking with the rotisserie rod.
FUNCTION
LEVEL FROM
BELOW
Thawing 1 30
Proving 1 40
TEMPERATURE
°C
TIME IN MINUTES
Depending on the
quantity.
27
Instructions for the user
ROTISSERIE COOKING
Prepare the rotisserie rod with the food, tightening the screws A of the
prongs. Fit the frame B onto the second runners from the bottom.
Remove the handle D and position the rotisserie rod so that the pulley E
is still in the guides on the frame B. Push the frame B fully in until the tip
of the rotisserie rod enters the hole C on the rear wall of the oven. Place
a basin F on the bottom shelf and pour a little water into it to prevent
smoke from forming.
Keep the oven door closed during cooking. Heating up time must not
exceed 60 minutes.
Regular flashing of the thermostat indicator light during cooking is
normal and indicates that the temperature is being maintained constant
inside the oven.
28
Instructions for the user
9. CLEANING AND MAINTENANCE
Before performing any operations requiring access to powered parts,
switch off the power supply to the appliance.
Do not use a steam jet for cleaning the inside of the oven.
9.1 Cleaning stainless steel
To keep stainless steel in good condition it should be cleaned regularly
after use. Let it cool first.
9.2 Ordinary daily cleaning
To clean and preserve the stainless steel surfaces, always use only
specific products that do not contain abrasives or chlorine-based acids.
How to use: pour the product on a damp cloth and wipe the surface, rinse
thoroughly and dry with a soft cloth or deerskin.
9.3 Food stains or residues
Do not use metallic sponges or sharp scrapers: they will damage
the surface.
Use normal non-abrasive products and a wooden or plastic tool if
necessary. Rinse thoroughly and dry with a soft cloth or
deerskin.
Do not allow residues of sugary foods (such as jam) to set inside
the oven. If left to set for too long, they might damage the enamel
lining of the oven.
29
Instructions for the user
9.4 Cleaning the inside of the oven
For best oven upkeep clean regularly after having allowed to cool. Take
out all removable parts.
• Clean the oven grill and side guides with hot water and non-abrasive
detergent. Rinse and dry.
• For easier cleaning, the door can be removed (see paragraph “10.2
Removing the door”).
The oven should be operated at the maximum heat setting for 15/20
minutes after use of specific products, to burn off the residues left inside
the oven.
9.5 Cleaning the door glazing
The glass in the door should always be kept thoroughly clean. Use
absorbent kitchen roll; remove stubborn dirt with a damp sponge and
ordinary detergent.
Do not use abrasive or corrosive cleaners for cleaning the door glazing.
(e.g., powder products, oven-cleaner sprays, stain removers and metal
scouring pads).
Do not use rough or abrasive materials or sharp metal scrapers to clean
the oven's glass doors since they may scratch the surface and cause the
glass to shatter.
30
Instructions for the user
10. EXTRAORDINARY MAINTENANCE
The oven may require extraordinary maintenance or replacement of parts
subject to wear such as seals, bulbs, and so on. The following instructions
describe how to carry out these minor maintenance operations.
Before any intervention disconnect the power supply of the device.
10.1 Changing the light bulb
Remove the bulb protector A by
turning it anticlockwise and
replace bulb B with a similar
one (25 W). Re-fit the bulb
protector A.
Use only oven bulbs (T 300°C).
10.2 Removing the door
10.2.1 With moveable levers
With the door completely
open, lift the levers A of
the two hinges until they
touch the hinges B and
take hold of the two sides
of the door with both
hands close to the hinges
themselves.
Raise the door to an angle of about 45° and remove it. If the hinges have
not locked, repeat the operation, raising the levers A and keeping the door
slightly raised. To reassemble, fit the hinges B into their grooves, then
lower the door into place, ensuring that it remains fitted into the grooves C,
then lower the levers A.
31
Instructions for the user
10.2.2 Removing doors with pins
Open the door completely and insert the pins (supplied) into the holes from the
inside. Close the door to an angle of about 45° and lift it off. To reassemble, fit the
hinges into their grooves, then lower the door into place and extract the pins.
10.3 Removing the door seal
To permit thorough cleaning of the oven, the seal may be
removed.
32
10.4 Removing the internal glass panels
The glass in the door should always be kept thoroughly clean. For easier cleaning,
it is possible to remove the door (see “10.2 Removing the door”) and place it on a
canvas; or open it and block the hinges in order to extract the glass panes.
The glass panes of the door can be completely removed by following the
instructions provided below.
Warning: before removing the glass panes, make sure that at least one of the
door's hinges has been locked in the open position as described in points “10.2
Removing the door”. This operation might have to be repeated during the glass
removal process if the door is accidentally freed.
Warning: replace the glass panes in the same order and in the same direction in
which they were removed. Finally, if the door was not removed, unlock the hinges
and close it.
Warning: do not use the product without the glass inserted, otherwise the external
surface of the door will overheat.
Instructions for the user
Removing the internal glass:
• Remove the internal glass pane
by pulling it towards you,
following the movement
indicated by the arrows. Doing
this dislodges the 4 pins
attached to the glass from their
slots in the oven door
Removing the middle glass
panes:
• Multifunction models have a
single middle pane. Remove the
middle pane by lifting it upwards
Cleaning:
• Now it is possible to clean the
external glass and the panes
removed previously. Use
absorbent kitchen roll paper. In
the case of stubborn dirt, wash
with a damp sponge and neutral
detergent.
Replacing the glass:
• Replace the glass panes in the
opposite order to which they
were removed.
• Reposition the internal glass
pane, taking care to centre and
insert the 4 pins attached to the
glass into their slots on the oven
door by applying a light pressure.
33
Instructions for the user
10.5 What to do if.
The oven display is full
off
The oven does not
heat up
The controls do not
respond.
The cooking times are
longer than those
indicated in the table.
If the door is opened
during a ventilated
function, the fans
stops.
If the problem has not been resolved or for other types of faults, contact
your local technical assistance centre.
• Check the mains power supply.
• Check whether an omnipolar switch
upstream from the oven feed line is in the
“ON” position.
• Check whether the “showroom” mode has
been set, for further details see paragraph
“Secondary menu” at page 19.
• Check whether the “child lock-out function”
mode has been set, for further details see
paragraph “Secondary menu” at page 19.
• Check whether the “2300 W” mode has been
set, for further details see paragraph
“Secondary menu” at page 19.
• This is not a fault. It is a normal operation of
the appliance, useful for when cooking foods
to avoid excessive heat escaping. When the
door is closed, the oven will return to normal
operation.
34
Instructions for the installer
11. INSTALLING THE APPLIANCE
11.1 Electrical connection
The I.D. plate with technical data, registration number and brand name is
positioned visibly on the oven door frame.
The plate must not be removed.
The appliance must be connected to earth in compliance with electrical
system safety regulations.
If a fixed connection is being used fit power line with an omnipolar circuit
breaker with a contact opening gap equal to or greater than 3 mm, in an
easily accessible position in proximity to the oven.
If a plug and socket connection is being used make sure that the plug and
socket are compatible. Avoid use of adapters and shunts as these could
cause overheating and risk of burns.
Operation at 220-240 V~: use a type
H05RR-F (3 x 1.5 mm
H05V2V2-F (3 x 1.5 mm
cable.
The earth wire (yellow-green) must be at least 20 mm longer than the
other wires at the end for connection to the appliance.
WARNING: THE VALUES INDICATED ABOVE REFER TO THE CROSSSECTION OF THE INTERNAL CONDUCTOR.
If the power supply lead has to be replaced, remove the rear casing by
undoing the screws as shown below. The cross-section of the power lead
must be at least 1.5 mm
temperatures up to 90°c (H05V2V2-F). Make sure that the cables follow
the best possible route and use band clamps to fix them at the side of the
cabinet, to avoid any contact with the oven.
2
) or type
2
) three-wire
2
(3 x 1.5 cable) and it must withstand
35
Instructions for the installer
11.2 Positioning the oven
The oven is designed for mounting into any piece of furniture as long as it
is heat-resistant. Proceed acording to the dimensions shown in Figures 1,
2 and 3. For installing under a work top, follow the dimensions given in
Figure 1-3. When installing under worktops incorporating combined hobs,
a gap of at least 110 mm must be left from any side wall, as shown in
figure 1.
When installing in tall units, comply with the dimensions shown in figure
1-2, bearing in mind that the top/rear of the unit must have an opening
80-90 mm deep. Tighten the 4 screws A inside the frame (fig. 1).
For installing beneath a non-integrated top, allow for a rear and bottom
clearance as shown in Figure 1 (ref. B). See relevant instructions for fitting
and securing the cook top.
36
Never use the oven door to lever the oven into
place when fitting. Avoid exerting too much
pressure on the oven door when open.
Instructions for the installer
It is recommended to install the oven with the help of a second person.
WARNING: When the oven has been extracted from the packing base,
avoid resting the product on the ground as this could cause deformation of
the drip trays. If necessary during handling, replace the oven in the
packing base.
37
Loading...