Contents
ITENEN
1 Instructions 4
1.1 Introduction 4
1.2 This user manual 4
1.3 Intended use 4
1.4 General safety instructions 5
1.5 Manufacturer liability 7
1.6 Identification plate 7
1.7 Disposal 7
2 Description 8
2.1 Product description 8
2.2 Description of parts 9
3 Use 12
3.1 Before first use 12
3.2 How to remove the blade assembly 12
3.3 Using the blender 14
3.4 Functions 17
3.5 Speed setting suggestions 18
4 Cleaning and care 20
4.1 Instructions 20
4.2 Cleaning the motor base 20
4.3 Cleaning the blender jug and blade assembly 20
4.4 Using the Self-clean option 20
4.5 Cleaning other blender parts 20
4.6 What to do if... 21
5 Recipes 23
We advise you to read this manual carefully, as it contains all the instructions for maintaining the appliance’s aesthetic
and functional qualities.
For further information on the product: www.smeg.com
The manufacturer reserves the right to make any changes deemed useful for improvement of its products without prior
notice. The illustrations and descriptions contained in this manual are therefore not binding and are merely indicative.
3
Instructions
1 Instructions
1.1 Introduction
Key information for the user:
Instructions
General information on this user
manual, on safety and final
disposal.
Description
Appliance description.
Use
Information on using your appliance
Cleaning and care
Information for proper cleaning and
maintenance of the appliance.
Recipes
List of recipes
Safety instructions
Information
Advice
1.2 This user manual
This user manual is an integral part of the
appliance and must therefore be kept in its
entirety and within the user’s reach for the
whole working life of the appliance.
1.3 Intended use
• Use the appliance only indoors.
• This appliance has been designed
specifically for domestic use. It must only
be used for blending, emulsifying
ingredients and crushing ice. Do not use
the appliance for anything other than its
intended use.
• This appliance is intended for use in a
home environment. Every other use is
considered improper. It also can be used
in:
• Staff kitchen areas in shops, offices
and other working environments
• Farm houses
• By guests in hotels, motels and other
residential type environments
• Bed and breakfast type environments.
• The appliance is not designed to
operate with external timers or with
remote-control systems.
• This appliance may not be used by
people of reduced physical, sensory or
mental capacity, or without sufficient
experience and knowledge (including
children), unless they are supervised or
instructed by adults who are responsible
for their safety.
• Children must never play with the
appliance. Keep the appliance out of
children’s reach.
4
Instructions
ITENEN
1.4 General safety instructions
Follow all safety instructions in order to be
able to use the appliance safely.
• Read this user manual carefully before
using the appliance.
• Switch off the appliance immediately
after use.
• Do not leave the appliance unattended
while it is operating.
• Disconnect the appliance from the
power socket as soon as you have
finished using it and before cleaning it.
• Do not immerse the appliance, the
power cord or the plug in water or any
other liquid.
• Do not use the appliance when the
power cord or the plug is damaged or
when the appliance has been dropped
or is damaged in any manner.
• If the supply cord is damaged, it must be
replaced by the service agent in order to
avoid a hazard.
• The cable is short to prevent accidents.
Do not use an extension cord.
• Ensure the cord does not come into
contact with sharp edges.
• Do not pull on the cord to unplug it from
the power socket.
• Do not place the appliance above or
near lit hob burners or electric rings,
inside an oven or near other heat
sources.
• Do not try to repair the appliance
yourself or without the intervention of a
qualified engineer.
• In the event of a fault, repairs should only
be carried out by a qualified engineer.
• Do not modify the appliance.
• Never try to put out a fire or flames with
water: turn off the appliance and remove
the plug from the socket and smother the
flames with a fire blanket or other
appropriate cover.
• Disconnect the appliance from the
power socket as soon as you have
finished using it and before cleaning it.
5
For this appliance
Instructions
• Avoid touching moving parts. Keep
hands, hair and clothing, and utensils
away from the blades during operation,
to prevent personal injury and/or
damage to the appliance.
• Care shall be taken when handling and
emptying the jug and during cleaning.
• Always disconnect the blender from the
supply if it is left unattended and before
assembly, disassembly or cleaning.
Unplug the blender when it is not being
used, before cleaning it and if you notice
any fault. Let the appliance cool down
before cleaning.
• Always use the blender with the lid in
place.
• Check that the lid is correctly closed
before turning on the blender.
• Do not overfill the blender (max. 1.5 litres).
• Do not use the blender with parts or
accessories of other manufacturers.
• Only use original spare parts. The use of
spare parts not approved by the
manufacturer could lead to fires, electric
shocks or personal injury.
• Only place the blender on level and dry
surfaces.
• Do not run the blender empty.
• Do not use the blender as a storage
compartment. Keep it empty before and
after use.
• Let liquids cool down to room
temperature before placing them in the
blender.
• Avoid touching moving parts, such as the
blade assembly.
• To avoid the risk of cuts, and damage to
the blender, do not put your hands or
tools like cutlery, etc. into the blender jug
while it is operating. You can use a wood
or plastic spatula only when the blender
is off.
• Do not use harsh detergents or sharp
objects to wash or remove residues from
the blender jug.
6
Instructions
ITENEN
1.5 Manufacturer liability
The manufacturer shall not be liable for
damage to persons or property caused by:
• Use of the appliance other than as
envisaged
• Not having read the user manual
• Tampering with any part of the
appliance
• Use of non-original spare parts
• Failure to observe the safety instructions
1.6 Identification plate
The identification plate bears the technical
data, serial number and brand name of the
appliance. Do not remove the identification
plate for any reason.
1.7 Disposal
This appliance must be disposed of
separately from other waste
(Directive 2012/19/EU). The
appliance does not contain substances in
quantities sufficient to be considered
hazardous to health and the environment, in
accordance with current European
directives.
• Old appliances do not belong in
household waste! To comply with
current legislation, old appliances, on
reaching the end of their useful lives,
should be taken to a disposal facility
where they can be sorted. In this way,
any valuable material contained in the
old appliances can be recycled, helping
to protect the environment. The relevant
local authorities or their waste disposal
operators can provide further
information.
The appliance is packed in non-polluting
and recyclable materials.
• Dispose of the packing materials at an
appropriate disposal facility.
Plastic packaging
Danger of suffocation
• Do not leave the packaging or any part
of it unattended.
• Do not let children play with the plastic
bags.
Electrical voltage
Danger of electrocution
• Disconnect the main power supply.
• Disconnect the power cable from the
electrical system.
7
2 Description
1
2
9
6
10
8
7
5
4
3
2.1 Product description
Description
1 Measuring cup
2 Lid with pouring hole
3 1.5 litre Tritan
4 Detachable blade assembly
5 Motor base
6 Pulse button
7 Control knob
8 START/STOP button
9 Handle
10 Built-in cord wrap
8
TM
BPA-Free jug
Model BLF01 - Blender
Description
ITENEN
2.2 Description of parts
Measuring cup (1)
Convenient measuring cup. It can be used
for measuring ingredients and as a device
to unscrew the blade assembly from the
base of the jug. See ”3.2 How to remove
the blade assembly”.
Lid with pouring hole (2)
TM
1.5 litre Tritan
The large-capacity jug is made of Tritan
BPA-Free jug (3)
TM
,
which is a safer, lighter and easier to handle
TM
material than glass. Tritan
is also resistant
to impacts, scratches and heat.
The jug features a handy lip and is marked
in both litres and cups.
It has a capacity that ranges from a
minimum of 0.25 l (1 cup) to a maximum of
1.5 litres (6 cups).
The lid has a seal that closes the blender
jug tightly. It has a pouring hole in the centre
to make the addition of ingredients easier
during blender operation.
9
Description
Detachable blade assembly (4)
Stainless steel detachable blade to crush
ice cubes and prepare delicious smoothies,
milkshakes, cocktails, etc.
It can be unscrewed from the base of the
jug to be cleaned.
Sharp blades
Danger of cuts
• Never touch the blades with your hands.
• Remove the blade assembly only using the
measuring cup, as indicated in section
”3.2 How to remove the blade assembly”.
Motor base (5)
The base houses a powerful 800 watt motor.
To avoid damage to the blender,
the appliance is equipped with a
safety lock system which shuts off
its operation when the jug is
removed. It also features a motor
safety cut-out which trips if the
motor is overloaded.
10
The accessories intended to come
into contact with food are made of
materials that comply with the
provisions of current legislation.
Description
ITENEN
Pulse button (6)
Press this button to get the maximum
blending speed. Perfect for most
demanding tasks. It can be used for a
maximum of 2 seconds at a time.
Control knob (7)
START/STOP button (8)
Press this button to start/stop blender
operation.
The control knob allows you to select one
of the four speeds available from 1 to 4.
The control knob features also 2 pre-set
programs: smoothie and ice crush.
See ”3.5 Speed setting suggestions” for
further information on which speed to use.
11
Use
3
2
3 Use
Danger of electrocution
• Plug into a earthed 3-prong outlet.
• Do not remove the earth prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions could
result in death, fire, or electrical shock.
3.1 Before first use
1. Remove all stickers and labels from the
blender and clean the motor base with a
damp cloth.
2. Remove the blender jug.
3. Remove the blade assembly (see ”3.2
Ho w t o r em ov e t he bla de ass em bl y” ).
4. Wash and dry thoroughly (see ”4.3
Cleaning the blender jug and blade
assembly”).
3.2 How to remove the blade
assembly
1. Take hold of the handle (1) and lift the
blender jug.
1
2. Remove the lid (2) from the blender jug
and the measuring cup (3) from the lid.
Danger of sudden start-up
• Make sure the blender is unplugged
before fitting or removing the blade
assembly.
12
Use
ITENEN
4
3. Turn the jug upside down and place it on
a flat surface. Insert the open end of the
measuring cup (3) into the base of the
blade assembly.
3
4. Unscrew the blade assembly (4) from the
jug body, turning the measuring cup anticlockwise. Manually remove the blade
assembly (4) from the jug body.
13
Use
5. Wash the jug, measuring cup, and blade
assembly in warm soapy water or in the
dishwasher (apart from the blade
assembly).
The blender jug can be washed in
a dishwasher without placing it
upside down (see picture below).
6. Dry thoroughly and replace the blade
assembly into the jug body following the
operations indicated previously in the
reverse order. Make sure to insert the
blade assembly until it locks into place.
3.3 Using the blender
1. Insert the blender jug onto the motor
base.
2. Introduce the ingredients into the jug,
paying attention not to exceed the
maximum capacity (1.5 l - 6 cups).
14
Use
ITENEN
3. Position the lid with the measuring cup
fitted onto the blender jug. Ensure the lid
is firmly screwed on.
4. Plug the blender into a power socket and
switch the socket on.
The red LED will turn on to indicate the
presence of power.
Select the desired speed or a pre-set
program using the control knob or press
the PULSE button to operate it manually.
The PULSE button can be used
alone or in combination with
speeds 1 to 3 to reach the
maximum speed.
5. Press the START button to start blending.
See the table ”3.5 Speed setting
suggestions” for further information on
the most suitable speed to use.
Speeds 1 - 4 allow continuous
blending. You can stop the
operation by pressing the STOP
button.
The speed can be changed at any
time during the blending process.
Important
• Do not operate manual speeds 1-4 for
more than 1 minute at a time.
• When the blender jug is filled up to or
near the maximum capacity (1.5 l),
place one hand on the blender lid to
avoid displacement of the lid during
operation.
15
Use
6. You can add further ingredients whilst
blending by removing the measuring cup
and pouring ingredients through the hole
in the lid.
7. If you have selected a speed between 1
and 4, when you have finished blending,
press the STOP button, turn the knob to ‘0’
and unplug the blender.
Cancelling/stopping the blending cycle
The blending cycle can be cancelled or
stopped at any time pressing the START/
STOP button.
16
ITENEN
3.4 Functions
Use
Safety lock system
The blender has a safety lock system which
automatically shuts off the blender when the
jug is removed from the base. It also
features a motor safety cut-out which trips
if the motor is overloaded.
Smooth Start
The Smooth Start function starts the
appliance up with a reduced initial speed,
regardless of the speed set with the control
knob.
The speed progressively increases until the
set speed is reached.
The Smooth Start function allows you to
process ingredients gradually to improve
the blending results.
The Smooth Start only works when
a speed between 0 and 4 is
selected and does not work with
the PULSE mode, ICE CRUSH or
SMOOTHIE programs.
Ice Crush and Smoothie
The pre-set ‘Ice Crush’ and ‘Smoothie’
programs automatically adjust the speed to
optimise blending results for a certain
factory set time, then turn off automatically.
Use the ICE CRUSH program with short
bursts of power when blending drinks
containing ice cubes or frozen fruit.
Use the SMOOTHIE program to blend
fruits, ice cream and yoghurt into thick
smoothies, blended drinks and milkshakes.
Pre-set time
Ice crush: approximately 50 seconds
Smoothie: approximately 60 seconds
When one of the two above mentioned
pre-set programs is selected, and after you
have pressed the START button, the blender
will automatically start to operate and the
central knob LED lights up to indicate that
the cycle is activated.
PULSE function
Pressing the PULSE button operates the
blender at maximum speed.
The blender shuts off immediately when the
button is released.
You should use a minimum quantity of
100g, not blending for more than 5
seconds consecutively, or 2 seconds when
using dry ingredients.
The PULSE function does not work
in combination with the ICE
CRUSH or SMOOTHIE programs.
17
3.5 Speed setting suggestions
Speed Suitable for
•Ice cubes
•Meat
PULSE
1 or 2
3 or 4
•Self-clean option (”4.4 Using the Self-clean option”).
•Mousses/Sorbets
•Batters/Salad dressings
•Blended frozen drinks
•Soups/Creamed soups
•Whipped cream
•Milkshakes/Smoothies
•Pesto/Fruit or vegetable purées
•Smoothies and milkshakes
•Smoothies with frozen fruit
Use
18
SMOOTHIES
•Ice cubes
•Pieces of frozen fruit/vegetables
ICE CRUSH
The speeds indicated in the table
are approximate and can vary
depending on the recipe and on
the interaction of the different
ingredients used.
ITENEN
Tips for using your blender
Use
• Cut into cubes the food to be blended to
obtain better results.
• Use the PULSE function for no more than
2 seconds at a time when blending dry
mixtures. You might need to stop
operation to push the ingredients down
the sides of the blender jug with a
spatula.
• When blending together liquid and dry
ingredients, blend liquids first and then
add the dry ingredients.
• Always remove stones from fruit and
bones from meat as they can damage
the blade assembly.
• Do not leave food residues dry on the
jug and blades for too long, as they
could be very difficult to remove. If you
cannot clean it right away, pour a little
warm water and let it soak.
• Do not process hot food. Let it cool to
room temperature before blending.
19
Cleaning and care
4 Cleaning and care
4.1 Instructions
Improper use
Danger of electrocution
• Unplug the blender before cleaning it.
• Do not immerse the motor base in water
or other liquids.
Improper use
Risk of damage to surfaces
• Do not use steam jets to clean the
appliance.
• Do not use cleaning products containing
chlorine, ammonia or bleach on parts
with metallic finishes (e.g. anodised,
nickel- or chrome-plated).
• Do not use abrasive or corrosive
detergents (e.g. powder products, stain
removers and metallic scourers).
• Do not use rough or abrasive materials
or sharp metal scrapers.
4.2 Cleaning the motor base
To keep the blender’s motor base outside
surfaces in good condition, they should be
cleaned regularly after use. Use a damp
and soft cloth with mild detergent.
4.3 Cleaning the blender jug and
blade assembly
Clean the appliance following the
instructions in section ”3.2 How to remove
the blade assembly”.
Sharp blades
Danger of cuts
• Never touch the blades with your hands.
• Remove the blade assembly only using the
measuring cup.
4.4 Using the Self-clean option
The blender jug and blade assembly can
be cleaned using the Self-clean option:
1. Fill the jug with warm water and mild
detergent.
2. Turn the control knob to the setting 1.
3. Press the START button.
4. Press the PULSE button for 2 seconds at
a time. Repeat the operation about 10
times.
5. Remove the jug, empty and rinse it.
6. Dry thoroughly.
4.5 Cleaning other blender parts
The blender lid and measuring cup can be
washed in warm soapy water or in the
dishwasher.
Make sure they have dried completely
before fitting them back on the blender.
20
ITENEN
4.6 What to do if...
Problem Possible cause Solution
Cleaning and care
The motor will not start
The motor has overheated.
The plug is not properly
inserted in the power socket.
The cable is defective.
Lack of power.
The blender is not resting on a
stable surface.
Unplug the blender and
leave the motor to cool.
Insert the plug into the power
socket. Do not use adaptors
or extensions.
Check that the house main
breaker is on.
Contact an Authorised
Service Centre.
Check that the house main
breaker is on.
Place the blender on a flat,
stable surface.
The blender vibrates
The anti-slip rubber feet are
worn.
The speed used is too high or
the load is excessive
Have them replaced at an
Authorised Service Centre.
Set a lower speed and
ensure the jug has not been
overfilled.
21
Cleaning and care
Problem Possible cause Solution
The blender switches on, but
the blades do not turn
The blender stops while
operating
The red LED of the knob
flashes at regular intervals
The blender stops during
operation and the white LED
flashes
If the problem has not been
resolved or in the event of another
type of fault, contact your local
technical support centre.
The jug has not been
correctly locked into its base.
The motor has overheated.
The jug is not correctly
inserted in the base.
The blades may have
jammed.
Remove the jug from its base
and lock it into place.
Unplug the blender and
leave the motor to cool.
Check the position of the jug
on the base.
Unplug the blender and free
the blades with a spatula.
22
ITENEN
5 Recipes
Recipes
Mixed fruit smoothie
Ingredients:
2 nectarines, stones removed (or tinned
peaches in syrup) and cut into pieces
125 g frozen raspberries
125 g frozen strawberries
125 ml orange juice
125 ml apple juice
Method
1. Put the nectarine pieces and the juices
into the blender jug.
2. Add the frozen fruit.
3. Turn the control knob to the Smoothie
program and start the blender by
pressing the START button.
4. Let it run for 40 seconds.
Soy milk
Ingredients for 1 litre of soy milk:
100 g yellow soy beans
1.4 litres water
Method
1. Wash 100 g of yellow soy beans in cold
water, discard the water then cover in
fresh cold water and leave them to soak
for 18-24 hours.
2. After they have soaked for 24 hours,
wash the soy beans, drain them and then
blend them with 400 ml of water at
speed 4 for 40 seconds, until you obtain
a homogeneous paste.
3. Bring the remaining 1 litre of water
almost to the boil in a pan.
4. Add the blended soy and cook,
skimming off any foam which might form.
Cook for 20 minutes from when it begins
to boil.
5. Turn off the heat and leave to rest for 20
minutes.
6. After 20 minutes, strain the soy milk
through clean muslin into a bottle.
7. You can sweeten and flavour the milk as
you prefer, using vanilla, honey, malt
extract or various syrups.
23
Recipes
Whipped cream
Ingredients:
500 g cold whipping cream
50 g icing sugar
Method
1. Whip the cream in the blender at speed
3 for approximately 30 seconds.
2. Stop the operation by pressing the STOP
button.
3. Add the icing sugar.
4. Select speed 4 and whip for a further 15
seconds, until the cream is fully whipped.
The cream can also be whipped
without icing sugar.
In this case, select speed 4 and
whip for 40 seconds.
Vegetable purée
Ingredients:
300 g courgettes
100 g water or vegetable stock
Method
1. Steam the courgettes and cut them into
rounds.
2. Put the pieces in the blender and blend
for 45 seconds at speed 4, adding a
little water or vegetable stock at a time
until you obtain a homogeneous purée.
24
Loading...