Smeg ALFA135BV, ALFA135XP, ALFA135B1, ALFA135XB, ALFA135XV User Manual

Contents

1. INSTRUCTIONS FOR SAFE AND PROPER USE _____________________ 20

2. INSTALLATION OF THE OVEN ___________________________________ 22

3. DESCRIPTION OF CONTROLS___________________________________ 25

4. USE OF THE OVEN ____________________________________________ 26

5. CLEANING AND MAINTENANCE _________________________________ 28

6. EXTRAORDINARY MAINTENANCE _______________________________ 30

7. ADDITIONAL INSTRUCTIONS FOR STEAM OVENS ____________________ 31

INSTRUCTIONS FOR THE INSTALLER: these are intended for the
qualified technician who must install the appliance, set it functioning
and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,
description of the commands and the correct procedures for cleaning
and maintenance of the appliance.

19

Introduction

1. INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN
ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE
OVEN. WE ADVISE READING THIS MANUAL AND ALL THE
INSTRUCTIONS THEREIN BEFORE USING THE OVEN.
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED
ENGINEERS IN ACCORDANCE WITH THE REGULATIONS IN
FORCE. THIS OVEN IS INTENDED FOR COMMERCIAL USES AND
CONFORMS TO CURRENT REGULATIONS IN FORCE. THE
APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING
FUNCTIONS: COOKING AND HEATING-UP OF FOOD. ALL OTHER
USES ARE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR
IMPROPER USE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT.
SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM
TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE
GROUNDED ACCORDING TO THE METHODS REQUIRED BY
SAFETY RULES.

WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE
THAT BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A
POWER CABLE COMPLYING WITH APPLICABLE REGULATIONS.

NEVER UNPLUG BY PULLING ON THE CABLE.

DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT
DISPERSAL SLITS.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF
INSPECTION TEST OF THE OVEN, FOLLOWING THE
INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT
FUNCTION, DISCONNECT IT FROM THE SUPPLY AND CALL THE
NEAREST TECHNICAL ASSISTANCE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.

20

Introduction

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE 0 (OFF)
POSITION WHEN YOU FINISH USING THE OVEN.

NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD
BE ACCIDENTALLY LIGHTED AND CAUSE FIRES.

THE APPLIANCE BECOMES VERY HOT DURING USE. SUITABLE
HEAT-PROOF GLOVES SHOULD BE WORN FOR ALL OPERATIONS.

THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER
AND BRAND NAME IS LOCATED IN AN EXPOSED POSITION AT THE
REAR OF THE OVEN.

THE PLATE MUST NOT BE REMOVED.

THE APPLIANCE IS INTENDED FOR COMMERCIAL USE BY
APPROPRIATELY TRAINED PERSONNEL. CHILDREN SHOULD

ALWAYS BE KEPT OUT OF ITS REACH AND NEVER BE ALLOWED
TO PLAY WITH IT.

BEFORE USE, THE OVEN DISHES MUST BE WASHED WITH A
SUITABLE DISHWASHING DETERGENT (DO NOT USE ABRASIVE
PRODUCTS).

THE OVEN DIMENSIONS ARE DESIGNED FOR A MAXIMUM LOAD
OF 7 KG.

REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL
GARBAGE COLLECTION CENTRE.

The manufacturer declines all responsibility for damage to persons
or things caused by non-observance of the above prescriptions or by
interference with any part of the appliance or by the use of non-original
spares.

21

Instructions for the installer

2. INSTALLATION OF THE OVEN

The oven must be set up on a perfectly flat surface and left standing
free. Make sure to allow enough room at the back for easy access to the
terminal strip for connection of the power cable to mains.
Installation must be carried out by a qualified technician in compliance
with applicable regulations in force.

2.1 Electrical connection

Make sure that the power line voltage matches the specifications
indicated on the rating plate located to the rear of the oven. This rating
plate must never be removed.

The oven is equipped with a power
converter which is designed to adapt
power input to local current rating.
The converter is factory-set at 3850W.
If required, this value may be
increased by adjusting the switch at
the rear of the oven by means of a
screwdriver.

MIN = Minimum power (3850W).
MED = Medium power (4250W).
MAX = Maximum power (5500W).

The connection terminals are
located at the rear of the
appliance. For electrical
connections see following
diagram. For access to the
terminal board, remove the
door located at the back of
the oven.

22

Instructions for the installer

For operation on 400-415V3N∼: use an

H05RR-F-type five-core cable (5 x 1.5 mm2).

For operation on 400-415V2N∼: use an
H05RR-F-type four-core cable (4 x 2.5
mm2).

For operation on 230-240V∼: use an
H05RR-F-type three-core cable (3 x 2.5
mm2).

The cable end to be connected to the
appliance must be provided with an ground
wire (yellow-green) at least 20 mm longer.

If connecting by plug and socket, make sure to use a 25 Amp. three-core
plug or a 16 Amp. five-core plug in case of operation at 400-415V2N∼ /
400-415V3N∼. Make sure that plug and wall socket are of the same type
and are in conformity with regulations in force. Also check that the power
supply line is provided with adequate earthing. Avoid using adapters or
shunters.

In case of permanent connection, ensure that power cable is equipped
with an easily accessible omnipolar switch fitted in proximity to the
apparatus and with a gap between contacts equal to or greater than
3 mm.

23