How it Works
SMC Networks
Loading...
YL500
User Manual
96 pgs2.12 Mb0
Table of contents
Loading...

SMC Networks YL500 User Manual

SMC1010W
Interactive Services-Indoor Camera
User Manual
Table of Contents
CHAPTER 1 INTRODUCTION..............................................................................................1
Physical Details - Network Camera.................................................................................4
Package Contents ..............................................................................................................6
CHAPTER 2 BASIC SETUP...................................................................................................7
System Requirements........................................................................................................ 7
Installation - Network Camera.........................................................................................8
Setup using the Windows Wizard....................................................................................9
CHAPTER 3 VIEWING LIVE VIDEO................................................................................14
Requirements...................................................................................................................14
Connecting to a Camera on your LAN..........................................................................14
Connecting to a Camera via the Internet......................................................................16
Viewing Live Video .........................................................................................................18
CHAPTER 4 ADVANCED VIEWING SETUP...................................................................20
Introduction.....................................................................................................................20
Adjusting the Video Image.............................................................................................20
Viewing Live Video via the Internet..............................................................................29
Motion Detection Alerts..................................................................................................30
CHAPTER 5 WEB-BASED MANAGEMENT....................................................................32
Introduction.....................................................................................................................32
Welcome Screen...............................................................................................................33
Administration Menu...................................................................................................... 34
System Screen..................................................................................................................35
Network Screen................................................................................................................37
DDNS Screen ...................................................................................................................42
User Database Screen......................................................................................................49
Motion Detection Screen.................................................................................................50
FTP Screen..................................................................................................................... .. 53
HTTP Screen ...................................................................................................................54
Event Trigger Screen ......................................................................................................55
Maintenance Screen........................................................................................................57
Status Screen....................................................................................................................59
CHAPTER 6 WINDOWS VIEWING/RECORDING UTILITY........................................62
System Tray Icon.............................................................................................................63
Main Screen.....................................................................................................................63
Camera Setup ..................................................................................................................64
i
CHAPTER 7 TROUBLESHOOTING..................................................................................75
Problems...........................................................................................................................75
APPENDIX A SPECIFICATIONS........................................................................................77
Network Camera.............................................................................................................77
Regulatory Approvals.....................................................................................................77
Copyright Notice..............................................................................................................78
APPENDIX B STREAMING VIDEO/AUDIO SOLUTION...............................................93
Streaming Video/Audio through Internet Camera.......................................................93
P/N: 956YFF0001 Copyright © 2009. All Rights Reserved. Document Version: 1.3
All trademarks and trade names are the properties of their respective owners.
ii
Chapter 1
Introduction
1
This Chapter provides details of the Network Camera's features, components and capabilities.

Overview

The Network Camera has an Integrated Microcomputer and a high quality CMOS digital­Image-Sensor, enabling it to display high quality live streaming video over your wired LAN, the Internet, and for the Network Camera, an 802.11g Wireless LAN.
Using enhanced MPEG-4 technologies, the Network Camera is able to stream high quality video and audio directly to your PC. The high compression capabilities of MPEG-4 reduce network bandwidth requirements to amazingly low levels.
A convenient and user-friendly Windows program is provided for both viewing and recording video. If necessary, you can even view video using your Web Browser, on a variety of software platforms.
Figure 1: Network Camera
Features
• Standalone Design. The Network Camera is a standalone system with built-in CPU and
Video encoder. It requires only a power source and a connection to your LAN or Wireless LAN.
Dual Video Support. The Network Camera can support both MEPG4 and MJEPG video
•
for different image compression.
1
•
Stream Live Video to Multiple Users. The MPEG4 encoder and HTTP server built
into the camera generate a ready-to-view video stream. Just connect to the camera using your Web browser or the provided Windows utility to view live video.
Suitable for Home, Business or Public Facilities. Whether for Home, Business or
•
Public Facility surveillance, or just for entertainment and fun, the Network Camera has the features you need.
Multi-Protocol Support. Supporting TCP/IP networking, SMTP (E-mail), HTTP and
•
other Internet related protocols, the Network Camera can be easily integrated into your existing network.
Easy Configuration. A Windows-based Wizard is provided for initial setup.
•
Subsequent administration and management can be performed using a standard web browser. The administrator can configure and manage the Network Camera via the LAN or Internet.
• Viewing/Recording Utility. A user-friendly Windows utility is provided for viewing
live video. For periods when you are absent, or for scheduled recording, this application also allows you to record video to an ASF file on your PC. The recorded files are in a standard Windows Media format, and thus usable by a wide variety of programs if required.
• Motion Detection. This feature can detect motion in the field of view. The Network
Camera will compare consecutive frames to detect changes caused by the movement of large objects. This function only works indoors due to the sensitivity of the CMOS sensor. When motion is detection, an E-mail alert can be sent, or some other action may be triggered.
Flexible Scheduling. You can limit access to the video stream to specified times using
•
a flexible scheduling system. The Motion Detection feature can also have its own schedule, so it is active only when required.
Syslog Support. If you have a Syslog Server, the Network Camera can send its log data
•
to your Syslog Server.
Audio Support. You can listen as well as look! Audio is encoded with the video if
•
desired. You can use either the built-in microphone or an external microphone.
Internet Features
• User-definable HTTP port number. This allows Internet Gateways to use "port
mapping" so the Network Camera and a Web Server can share the same Internet IP address.
DDNS Support. In order to view video over the Internet, users must know the Internet
•
IP address of the gateway used by the Network Camera. But if the Gateway has a dynamic IP address, DDNS (Dynamic DNS) is required. Since many existing Gateways do not support DDNS, this function is incorporated into the Network Camera.
NTP (Network-Time-Protocol) Support. NTP allows the Network Camera to
•
calibrate its internal clock from an Internet Time-Server. This ensures that the time stamp on Video from the Network Camera will be correct.
Security Features
• User Authentication. If desired, access to live video can be restricted to known users.
Users will have to enter their username and password before being able to view the video stream. Up to 5 users can be entered.
Password-Protected Configuration. Configuration data can be password protected, so
•
that it only be changed by the Network Camera Administrator.
2
Wireless Features (Wireless Model Only)
• Standards Compliant. The Network Camera complies with the IEEE802.11g (DSSS)
specifications for Wireless LANs.
Supports both 802.11b and 802.11g Standards. The Network Camera supports both
•
802.11b and 802.11g standards.
Speeds to 54Mbps. All speeds up to the 802.11g maximum of 54Mbps are supported.
•
Wired and Wireless Network Support. The Network Camera supports either wired or
•
wireless transmission.
WEP Support. Full WEP support (64/128 Bit) on the Wireless interface is provided.
•
WPA/WPA2 Support. The WPA Personal/WPA2 Personal standard is also supported,
•
allowing advanced encryption of wireless data.
WPS Support. WPS (Wi-Fi Protected Setup) can simplify the process of connecting any
•
device to the wireless network by using the push button configuration (PBC) on the Wireless Access Point, or entering a PIN code if there's no button.
3

Physical Details - Network Camera

Front - Network Camera
Figure 2: Front Panel
Privacy Button
Lens
Microphone Reset Button
Power LED (Green)
On (Green) - The privacy button is activated. Off - The privacy button is not in use.
No physical adjustment is required or possible for the lens, but you should ensure that the lens cover remain clean. The image quality is degraded if the lens cover is dirty or smudged.
The built-in microphone is mounted on the front. This button is recessed; you need a pin or paper clip can be used to
depress it. It can be activated at any time the camera is in the "ready" mode.
• Reset to manufacturer default valued and reboot. When
pressed and held over 10 seconds, the settings of Network Camera will be set to their default values.
Note:
After this procedure is completed, the Power LED will blink three times to confirm that the reset was completed successfully.
On - Power on. Off - No power. Blinking - The Power LED will blink during start up. This will take
15 to 20 seconds.
4
Network LED (Green, Amber)
On (Green) - Wireless or LAN connection is available. Off - Wireless or LAN is not connected or camera is not
sending/receiving data. Blinking (Green) - Data is being transmitted or received via the
LAN or Wireless connection. On (Amber) - If the LED is on, the WPS is not processing
successfully. Blinking (Amber) - WPS function is being processed.
Rear - Network Camera
Antenna
Speaker out Power Input
LAN port
WPS Button (Wireless Model Only)
Figure 3: Rear Panel
Attach the supplied antenna here. The antenna is adjustable; be st results are usually obtained with the antenna positioned vertically.
If required, an external speaker can be plugged in here. Connect the supplied 5V power adapter here. Do not use other
power adapters; doing so may damage the camera. Use a standard LAN cable to connect your Network Camera to a
10/100BaseT hub or switch.
Note:
• Plugging in the LAN cable will disable the Wireless interface. Only 1 interface can be active at any time.
• The LAN cable should only be connected or disconnected when the camera is powered OFF. Attaching or detaching the LAN cable while the camera is powered on does NOT switch the interface between wired and wireless.
Push the WPS button on the device and on your other wi reless device to perform WPS function that easily creates an encryption­secured wireless connection automatically.
• WPS PBC Mode. When pressed and released (less then 3 seconds), the Network Camera will be in the WPS PBC mode (Auto link mode).
• WPS Pin Code Mode. When pressed and held for over 3
5
seconds, the Network Camera will be in the WPS Pin Code mode.

Package Contents

The following items should be included: If any of these items are damaged or missing, please contact your dealer immediately.
1. Network Camera
2. Antenna (Wireless Model Only)
3. Power adapter
4. Installation CD-ROM
5. Quick Installation Guide
6
Chapter 2
Basic Setup
2
This Chapter provides details of installing and configuring the Network Camera.

System Requirements

• To use the wired LAN interface, a standard 10/100BaseT hub or switch and network cable is required.
• To use the Wireless interface on the wireless model, other Wireless devices must be compliant with the IEEE802.11b or IEEE802.11g specifications. All Wireless stations must use compatible settings.
The default Wireless settings are: Mode: Infrastructure
SSID: ANY Wireless Security: Disabled Domain: USA Channel No.: Auto
Figure 4: Installing Diagram
7

Installation - Network Camera

1. Assemble the Camera
Screw the supplied antenna to the mounting point on the rear. Attach the Camera Mount to the camera.
2. Connect the LAN Cable
Connect the Network Camera to a 10/100BaseT hub or switch, using a standard LAN cable.
For the Wireless Model, this will disable the Wireless Interface. The Wireless and LAN interfaces cannot be used simultaneously. Using the LAN interface is recommended for initial configuration. After the Wireless settings are correct, the Wireless interface can be used.
The first time you connect to the camera, you should connect the LAN cable and configure the Network Camera with appropriate settings. Then you can unplug the LAN cable and power off the camera. The Network Camera will be in wireless interface when you power on the camera again.
3. Power Up
Connect the supplied 5Vpower adapter to the Network Camera and power up. Use only the power adapter provided. Using a different on e may cause hardware damage.
4. Check the LEDs
• The Power LED will turn on briefly, then start blinking. It will blink during startup, which takes 15 to 20 seconds. After startup is completed, the Power LED should remain ON.
• The Network LED should be ON.
For more information, refer to Physical Details - Network Camera in Chapter 1.
8

Setup using the Windows Wizard

Initial setup should be performed using the supplied Windows-based setup W izard. This program can locate the Network Camera even if its IP address is invalid for your network. You can then configure the Network Camera with appropriate TCP/IP settings for your LAN.
Subsequent administration can be performed with your Web browser, as explained in Chapter 5 - Web-based Management.
Setup Procedure
1. Insert the supplied CD-ROM into your drive. If the setup program does not start
automatically, run NetworkCamera.exe in the root folder.
• You will see the Welcome screen shown below.
• Click the Setup Camera button to start the setup Wizard
Figure 5: Welcome Screen
2. The next screen, shown below, will list all the Network Cameras on your LAN.
Figure 6: Camera List Screen
9
• Select the desired Camera from the list on the left. The current settings for the selected
Camera will be displayed in the table on the right.
• Click Next to continue.
3. You will be prompted to enter the Administrator Name and Administrator Password, as
shown below.
• If using the default values, enter administrator for the name, and leave the
password blank.
• Otherwise, enter the Administrator Name and Administrator Password set on the
Maintenance screen.
Figure 7: Password Dialog
4. This screen allows you to enter a suitable Description, and set the correct Time Zone,
Date, and Time. Make any desired changes, then click Next to continue.
Figure 8: Camera Settings
5. On the following IP Address Settings screen, shown below, choose Fixed IP Address,
Dynamic IP Address or PPPoE.
10
Figure 9: Fixed or Dynamic IP Selection
• Fixed IP Address is recommended, and can always be used.
• Dynamic IP Address can only be used if your LAN has a DCHP Server.
• PPPoE (PPP over Ethernet) is the most common login method, widely used with
DSL modems.
Click Next to continue.
6. If you chose Fixed IP Address, the following TCP/IP Settings screen will be displayed.
Figure 10: TCP/IP Settings
• Enter an unused IP Address from within the address range used on your LAN.
• The Subnet Mask and Default Gateway fields must match the values used by PCs on
your LAN.
• The Primary DNS address is required in order to use the E-mail alert or Dynamic
DNS features. Enter the DNS (Domain Name Server) address recommended by your ISP.
• The Secondary DNS is optional. If provided, it will be used if the Primary DNS is
unavailable.
11
Click Next to continue.
7. If you chose PPPoE, the following PPPoE Settings screen will be displayed.
Figure 11: PPPoE Settings Screen
• Enter the User Name provided by your ISP.
• Enter the Password for the user name above.
Click Next.
8. The next screen, shown below, displays all details of the Network Camera.
• Click Next if the settings are correct
• Click Back to modify any incorrect values.
Figure 12: Save Settings
9. Click OK to confirm that you want to save the new settings. If you want to cancel your
changes, click Cancel.
12
Figure 13: Confirm Screen
10. After clicking OK, you will see the screen below.
Figure 14: Final Screen
Clicking the Install Utility button will install the Viewing/Recording utility described in Chapter 6 - Windows Viewing/Recording Utility.
11. Click Exit to end the Wizard.
Setup is now complete.
13
Chapter 3
Viewing Live Video
3
This Chapter provides basic information about viewing live video.

Overview

After finishing setup via the Windows-based Wizard, all LAN users can view live video using Internet Explorer on Windows.
This Chapter has details of viewing live video using Internet Explorer. But many other powerful features and options are available:
• To view multiple cameras simultaneously, or record video (either interactively or by schedule), you should install the Windows Viewing/Recording utility. Refer to Chapter 6 - Windows Viewing/Recording Utility for details on installing and using this program.
• The camera administrator can also adjust the Video Stream, and restrict access to the video stream to known users by requiring viewers to supply a username and password. See Chapter 4 - Advanced Viewing Setup for details.
• To make Live Video from the camera available via the Internet, your Internet Gateway or Router must be configured correctly. See Making Video available from the Internet in Chapter 4 - Advanced Viewing Setup for details.

Requirements

To view the live video stream generated by the Network Camera, you need to meet the following requirements:
• Windows 98/98SE, Windows 2000, Windows XP.
• Internet Explorer 6 or later.

Connecting to a Camera on your LAN

To establish a connection from your PC to the Network Camera:
1. Use the Windows utility to get the IP address of the Network Camera.
2. Start Internet Explorer.
3. In the Address box, enter "HTTP://" and the IP Address of the Network Camera.
4. When you connect, the following screen will be displayed.
14
Figure 15: Home Screen
5. Click View Video.
6. If the Administrator has restricted access to known users, you will then be prompted for a
username and password. Enter the name and password assigned to you by the Network Camera administrator.
7. The first time you connect to the camera, you will be prompted to install an ActiveX
component (OCX or CAB file), as in the example below.
You must install this ActiveX component (OCX or CAB file) in order to view the Video stream in Internet Explorer. Click the "Yes" button to install the ActiveX component.
Figure 16: ActiveX OCX Prompt
8. Video will start playing automatically. There may be a delay of a few seconds while the
video stream is buffered.
15

Connecting to a Camera via the Internet

You can NOT connect to a camera via the Internet unless the camera Administrator has configured both the camera and the Internet Gateway/Router used by the camera.
See Making Video available from the Internet in Chapter 4 - Advanced Viewing Setup for details of the required configuration.
Also, you need a broadband Internet connection to view video effectively. Dial-up connections are NOT supported.
To establish a connection from your PC to the Network Camera via the Internet:
1. Obtain the following information from the Administrator of the camera you wish to
connect to:
• Internet IP Address or Domain Name of the camera.
• Port number for HTTP connections.
• Login (username, password) if required.
2. Start Internet Explorer.
3. In the Address box, enter the following:
HTTP://Internet_Address:port_number Where Internet_Address is the Internet IP address or Domain Name of the camera,
and port_number is the port number used for HTTP (Web) connections to the camera.
Examples using an IP address:
HTTP://203.70.212.52:1024 Where the Internet IP address is 203.70.212.52 and the HTTP port number is 1024.
Example using a Domain Name:
HTTP://mycamera.dyndns.tv:1024
Where the Domain name (using DDNS in this example) is mycamera.dyndns.tv and the HTTP port number is 1024.
16
4. When you connect, the following screen will be displayed.
Figure 17: Home Screen
5. Click View Video.
6. If the Administrator has restricted access to known users, you will then be prompted for a
username and password. Enter the name and password assigned to you by the Network Camera administrator.
7. The first time you connect to the camera, you will be prompted to install an ActiveX
component (OCX or CAB file), as in the example below.
You must install this ActiveX component (OCX or CAB file) in order to view the Video stream in Internet Explorer. Click the "Yes" button to install the ActiveX component.
Figure 18: ActiveX OCX Prompt
8. Video will start playing automatically. There may be a delay of a few seconds while the
video stream is buffered.
17

Viewing Live Video

After installing the ActiveX component, you will be able to view the live video stream in its own window, as shown below.
Figure 19: View Video Screen
There are a number of options available on this screen, accessed by select list, button or icon. See the table below for details.
Note: The options can only be configured while using IE browser. Other browsers can just view the video rather than configuration.
General Options
These options are always available, regardless of the type of camera you are connected to.
Resolution. Use this drop-down list to select the desired video size. Zoom. A digital zoom feature is available. To zoom in on a section of the
window, click this icon. Then use your mouse to select the section you want to magnify. Click the icon again to disable the zoom feature.
Snapshot. Click this to take a single JPEG "snapshot" image of the current video.
Flip. Click this to have the image swapped top-to-bottom.
Mirror. Click this to have the image swapped left-to-right.
Audio On. This icon is displayed if audio is On. Click on the icon to turn
audio Off. Volume. If audio is enabled, use this slider to adjust the volume.
18
Setup. Select the desired setup format from the drop-down list.
19
Chapter 4
Advanced Viewing Setup
This Chapter provides information about the optional settings and features for viewing video via the Network Camera. This Chapter is for the Camera Administrator only.

Introduction

This chapter describes some additional settings and options for viewing live Video:
• Adjusting the video image
• Controlling user access to the live video stream
• Making video available from the Internet
• Using the Motion Detection feature

Adjusting the Video Image

If necessary, the Network Camera Administrator can adjust the Video image.
To Adjust the Video Image:
4
1. Connect to the Web-based interface of the Network Camera. (See Chapter 5 - Web- based
Management for details.)
2. Select Administration, then Video Image. You will see a screen like the example below.
Figure 20: Video Image Screen
3. Make the required adjustments, as explained below, and save your changes.
20
MPEG-4 Settings
Resolution
Video Quality Control
Max. Frame Rate
MJPEG Settings
Resolution
Fixed Video Quality
Max. Frame Rate
Select the desired video resolution format. The default resolution is set to 640*480.
• Constant Bit Rate: Select the desired bit rate. The default is set to 256 Kbps.
• Fixed Quality: Select the desired option. The default fix quality is set to Very High.
Select the desired Maximum bandwidth for the video stream. Note that you can specify EITHER the Bandwidth OR the Frame Rate, not both. If the Bandwidth is defined, the frame rate will be adjusted as necessary to achieve the specified frame rate.
The default value for bandwidth is 30.
Select the desired video resolution format. The default resolution is set to 640*480.
Select the desired fix quality. The default fix quality is set to Very High.
Select the desired Maximum bandwidth for the video stream. Note that you can specify EITHER the Bandwidth OR the Frame Rate, not both. If the Bandwidth is defined, the frame rate will be adjusted as necessary to achieve the specified frame rate.
The default value for bandwidth is 30.
Mobile Settings
Enable Mobile Streaming
Resolution Video Quality
Control
Max. Frame Rate Access Code
Video Adjustment
Power Line Frequency
White Balance
Lighting Condition Brightness
Enable streaming video for the mobile device by checking this checkbox.
The default resolution is set to 160x120.
• Constant Bit Rate: Select the desired fix bit rate.
• Fixed Quality: Select the desired option. The default fix quality
is set to Normal.
Select the desired Maximum bandwidth for the video stream. Enter the code for accessing the live video from camera through cell
phone connection.
Select the power line frequency (50Hz or 60Hz) used in your region, to improve the picture quality under florescent lighting.
Select the desired option to match the current environment and lighting.
Select the desired option to match the current lighting condition. If necessary, you can adjust the brightness to obtain a better image.
For example, if the camera is facing a bright light, the image may be too dark. In this case, you can increase the brightness.
21
Sharpness
Options
Microphone
Audio Type Speaker Flip Mirror Time Stamp Text Display
Select the desired option for the sharpness. You can select a Sharpness value between -3 and 3.
Enable audio by checking this checkbox. Using Audio will increase the bandwidth requirements slightly.
Select the desired audio type. Enable speaker sound by checking this checkbox. This setting will have the image swapped top-to-bottom. This setting will have the image swapped left-to-right. If enabled, the current time will be displayed on the Video image. Enable this setting if you want text to be displayed on the Video
image, and enter the desired text - up to 20 characters. This feature is often used to identify each camera when multiple cameras are installed.
22

Viewing the live Video on your cell phone

The live streaming of the Network Camera can even be viewed from a compatible cell phone, so you can keep an eye on things almost everywhere you go. It’s just as easy as following the required steps.
To Adjust the Mobile Settings
1. Connect to the Web-based interface of the Network Camera. (See Chapter 5 - Web- based Management for details.)
2. Select Administration, then Video & Audio. You will see a screen like the example below.
Figure 21: Mobile Settings
3. Check the checkbox of Enable Mobile Streaming and configure the related settings in the Mobile Settings section, as explained below. Save your changes.
Mobile Settings
Enable Mobile Streaming
Resolution Video Quality
Control
Max. Frame Rate Access Code
Enable streaming video for the mobile device by checking this checkbox.
The default resolution is set to 160x120.
• Constant Bit Rate: Select the desired fix bit rate.
• Fixed Quality: Select the desired option. The default fix quality
is set to Normal. Select the desired Maximum bandwidth for the video stream. Enter the code for accessing the live video from camera through cell
phone connection.
Connecting Cell Phone to the Network Camera
A number of different mobile handsets are compatible with the Network Camera. Follow the suggested steps (steps may differ according to the mobile phone you use).
Before connecting to the cell phone, please make sure the following:
• Mobile phone should be supported by 3GPP pr ot ocol.
• Camera Web management - RTSP port number needs to be entered. Default is 554.
• Access code: 8 digits (0~9)
23
Steps:
1. Start IE
2. Select Add Bookmark
3. Click Edit
4. Enter desired value for Subject or leave it blank
5. Enter the camera’s IP address into the Address box.
RTSP://Internet_Address:port_number
6. Click Play
24

Controlling User Access to the Video Stream

By default, anyone can connect to the Network Camera and view live Video at any time. If desired, you can limit access to scheduled times, and also restrict access to known users.
To Control User Access to Live Video:
1. Connect to the Web-based interface of the Network Camera. (See Chapter 5 - Web- based Management for details.)
2. Select Administration, then Video Access.
3. Set the desired options for Access.
Access
If the Video Access is disabled, users cannot connect using either their Web Browser or the Windows utility. However, viewing video is still possible by logging in as the Administrator.
Figure 22: Controlling User Access
See Chapter 5 - Web-based Management for further details about using the Video Access and User Database screens.
25

Making Video available from the Internet

If your LAN is connected to the Internet, typically by a Broadband Gateway/Router and Broadband modem, you can make the Network Camera available via the Internet. You will need to configure your Router or Gateway to allow connections from the Internet to the camera.
Router/Gateway Setup
Your Router or Gateway must be configured to pass incoming TCP (HTTP) connections (from Internet Viewers) to the Network Camera. The Router/Gateway uses the Port Number to determine which incoming connections are intended for the Network Camera.
This feature is normally called Port Forwarding or Virtual Servers, and is illustrated below. The Port Forwarding/Virtual Server entry tells the Router/Gateway that incoming TCP connections on port 1024 should be passed to the Network Camera. If n ecessary, check the user manual for your Router/Gateway for further details.
Figure 23: Connecting via the Internet
The "Port" for the Port Forwarding / Virtual Server entry above is the " Secondary Port" number specified on the Network screen of the Network Camera.
26
Loading...
+ 67 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use