SMC Networks WSKP100 User Manual

WSKP100 Wi-Fi Phone

User Guide

www.smc.com

The whole world can talk for free.

Skype.Com

User Guide Guide

Wi-Fi Phone

IEEE 802.11b/g Wireless Phone with Skype Support

WSKP100 E072006-EK-R02 149100035700E

Compliances

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

IMPORTANT NOTE: FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.

Japan VCCI Class B

EC Conformance Declaration

Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards:

• EN 60950-1 (IEC 60950-1) - Product Safety

• EN 300 328 - Technical requirements for 2.4 GHz radio equipment

• EN 301 489-1, EN 301 489-17 - EMC requirements for radio equipment

This device is intended for use in the following European Community countries:

• Austria • Belgium • Denmark

• Finland • France • Germany

• Italy • Luxembourg • Netherlands

• Norway • Spain • Sweden

• Switzerland • United Kingdom • Portugal

• Greece • Ireland • Iceland

Requirements for indoor vs. outdoor operation, license requirements and allowed channels of operation apply in some countries as described below:

• In Italy the end-user must apply for a license from the national spectrum authority to operate this device outdoors.

• In Belgium outdoor operation is only permitted using the 2.46 - 2.4835 GHz band: Channel 13.

• In France outdoor operation is only permitted using the 2.4 - 2.454 GHz band: Channels 1 - 7.

Contents

Chapter 1: Introduction 1-1

Package Checklist 1-1 Hardware Description 1-2

AC Power Charger 1-3 Mini USB Cable 1-3

Chapter 2: Installing the Battery 2-1

Charging the Battery 2-2 Powering On the Phone 2-3

Chapter 3: Getting Started 3-1

First-Time Startup 3-1 Understanding the Phone’s LCD Display 3-3

The Main Menu 3-5

The Power Key Menu 3-6 Creating a New Skype Account 3-7 Setting Up Your Contacts 3-8 Making a Call 3-8

Chapter 4: Managing Contacts 4-1

Adding a Contact 4-1 Adding a SkypeOut Contact 4-2 Searching for Contacts 4-3 The Contacts Options Menu 4-4 Blocking a Contact 4-5

Chapter 5: Making and Receiving Skype Calls 5-1

Skype-to-Skype Calls 5-1 Receiving Skype Calls 5-2 SkypeOut Calls 5-3 Dialing a Direct Call 5-4 Receiving SkypeIn Calls 5-5 Diverting a Call 5-6 Sending Skype Voicemail 5-7 Listening to Skype Voicemail 5-8

iii

Contents

Recording a Voicemail Greeting 5-9 History Lists 5-10

Chapter 6: Personal Skype Settings 6-1

Changing Your Skype Status 6-1 Setting Your Profile 6-2 Changing Your Password 6-3 Privacy Settings 6-4

Chapter 7: Wi-Fi Network Settings 7-1

Finding Wi-Fi Networks 7-1 Preferred Networks 7-2 Setting Access to Open Networks 7-3

Chapter 8: General Settings 8-1

Changing the Display Language 8-1 Changing Display Settings 8-2 Setting Alert Tones 8-3 Setting the Time and Date 8-4 Displaying Phone Settings 8-5 Clearing Phone Settings 8-6 Advanced Settings 8-7

Appendix A: Specifications A-1

Appendix B: Skype End User License Agreement B-1

Chapter 1: Introduction

The WSKP100 is a Wi-Fi (IEEE 802.11b/g) wireless phone that enables you to make Skype calls without using a computer. The phone enables you to use your normal Skype account with complete mobility, allowing you to talk from any location where you have an Internet connection through a nearby access point.

Package Checklist

The WSKP100 Wi-Fi Phone package includes these items:

•One Wi-Fi Phone (WSKP100)

• One Lithium-Ion battery

•One headset

•One mini USB cable

•One AC power charger

•Quick Start Guide

•User Manual CD

Inform your dealer if there are any incorrect, missing or damaged items. If possible, retain the carton, including the original packing materials. Use them to repack the product in case there is a need to return it.

1-1

Introduction

Hardware Description

Volume

Button

Left

Soft Key

Send

Alphanumeric

Keypad

Key

USB/Power

Charge Port

LCD

Display

Navigation

Key

Right

Soft Key

End/Power

Key

Headset

Jack

Before preparing the Wi-Fi Phone for use, first become familiar with its main keys, buttons, and other hardware features.

1.LCD Display — Color software menu display.

2. Navigation Key — Four-direction software navigation key. Pressing the key

down selects the current option.

3.Right Soft Key — Negative action key. Cancels or returns to previous menu.

4.End/Power Key — Ends an active call. Turns the power on and off.

• Press for more than two seconds to power the phone on.

• When on, press for two to four seconds to access the Power Key menu.

• Press for more than four seconds to power the phone off.

1-2

Hardware Description

5.Headset Jack — Jack for headset connection.

6.USB/Power Charge Port — Power charger connection for charging battery.

7.Alphanumeric Keypad — Includes 0-9, A-Z, *, and # keys.

• The [a/A *] key selects upper- or lower-case characters, numbers, or hexadecimal.

• The [ 1 ] key selects common punctuation marks during text input.

• The [ # ] key selects special characters and symbols during text input.

8.Send Key — Calls a selected contact.

9.Left Soft Key — Positive action key. Selects menu option.

10. Volume Button — Adjusts volume of the speaker.

Keypad Lock — The phone keypad can be locked by pressing the Left Soft Key

together with the [a/A *] key. Pressing the two keys again unlocks the keypad.

AC Power Charger

The Wi-Fi Phone will charge an installed battery when connected to the AC power charger, and the power charger is connected to a power source. The power charger automatically adjusts to any voltage between 100-240 volts at 50 or 60 Hz. No voltage range settings are required.

Mini USB Cable

The Wi-Fi Phone includes a mini USB cable that can be used to charge the phone’s battery from a connected PC.

1-3

Introduction

1-4

Chapter 2: Installing the Battery

After unpacking the Wi-Fi Phone, you must first install and charge the battery pack before turning on the phone.

Warning: Risk of explosion if battery is replaced by an incorrect type. Dispose of

used batteries according to the instructions.

Caution: Use only the Lithium-Ion battery pack supplied with the phone. Do not

try to install any other battery. To obtain replacement batteries, contact your local dealer.

1. Remove Battery Compartment Cover — Place the phone face down. Push

and slide down the battery compartment cover until it becomes free.

2. Install Battery — Place the battery into the compartment. Be sure the text

label on the battery is facing out and the battery’s three metal contacts point to the top of the phone.

Push Off

Install Battery

3. Replace Battery Compartment Cover — Slide the battery compartment

cover back onto the phone until it clicks firmly into place.

2-1

Installing the Battery

Charging the Battery

1. Connect the AC Power Charger — Lift up the rubber cover on the mini USB

charger port and connect the power charger to the port. Then, plug the charger into an AC electrical outlet.

Note: The power charger automatically adjusts to any voltage between 100-240 volts

at 50 or 60 Hz.

Fully Charge Battery — For the first time use, allow eight hours to fully

charge the battery before turning on the phone.

Lift Cover

Connect Charger

3. Disconnect the Power Charger — When the battery is fully charged, remove

the power charger from the phone and push down the charger port’s rubber cover.

Note: When you next have to charge the phone’s battery, you do not have to power

off the phone. Just connect the charger as described above and wait until the LCD display indicates the battery is fully charged. After the first charge, the charge time is about three hours.

2-2

Powering On the Phone

Push and hold down the End/Power key for more than two seconds to power on the phone. The LCD display turns on showing an image of a white sun on a yellow background.

Allow 30 seconds for the phone to start up.

Go to Chapter 3 “Getting Started” to learn how to set up a Wi-Fi network connection and start using the phone.

Power On

ABC

GHI

PQRS

a/A

JKL

TUV

DEF

MNO

WXYZ

2-3

Installing the Battery

2-4

Chapter 3: Getting Started

The Wi-Fi Phone requires a wireless connection to a Wi-Fi access point to operate. In addition, the access point network must provide access to the Internet to make Skype calls.

You can set the phone to connect to specific wireless networks or search for “open” networks. Wireless network information is stored in the phone’s memory as “Preferred Networks” that are searched for each time the phone is powered on.

When powering on the Wi-Fi Phone for the first time, there are no Preferred Networks in the phone’s memory. You need to select a wireless network and sign into your Skype account before you can start making calls.

First-Time Startup

When the Wi-Fi Phone is used for the first time, follow these steps to set up the phone and make a network connection:

1. Select the language of the display. The default is

English.

2. Read and accept the Skype Agreement statement. .

“No Emergency Calls. Skype is not a replacement for your ordinary telephone and cannot be used for emergency calling. I have read and accept the Skype’s terms and conditions at www.skype.com/eula and www.skype.com/tos and in my device user guide.”

See Appendix B for the full text of the Skype Agreement.

You must accept the Agreement to use the phone. Press the Left Soft Key to accept the Agreement.

3-1

Getting Started

3. The phone scans for nearby wireless networks and

lists those that it finds.

Normally, you need to be within 90 m (300 ft) of a network’s wireless access point to be able to connect to it. If the network you want to connect to is not on the list, move to another location and try again.

4. From the wireless networks list, select the wireless

network that you want to connect to and press the Left Soft Key to access Options menu. Then select “Connect.”

If a security key is required, the phone prompts for the key value. Security keys should be provided by the wireless network operator.

The access point information is stored in the phone’s memory as a “Preferred Network” and will be used next time the phone is powered on.

5. If you already have a Skype account, sign in with your

user name and password.

Note: If you are already signed into your Skype account from

your PC, you should sign out first before using the phone. You cannot sign into your Skype account from two devices at the same time.

You can also create a new account using the phone. See “Creating a New Skype Account” on page 3-7.

When your Skype login is successful, you can start making calls. Your current Contacts should display in the Contacts screen.

3-2

Understanding the Phone’s LCD Display

The Wi-Fi Phone’s color LCD display provides various status indicators and access to the menu-based interface. The illustration below shows the main screen and its elements.

Wireless Signal Status

Skype Online Status

Skype Credit

Left Soft Key Action

Battery Status — Indicates the status of the battery. The following states may be displayed:

The battery is at a very low level and should be charged immdiately.

The battery is at a partially charged level.

The battery is fully charged.

The battery is charging from a low level.

The battery is charging, reaching a partially charged level.

The battery is charging, reaching a fully charged level.

Wireless Signal Status — Indicates the strength of the Wi-Fi network signal. The following states may be displayed:

There is no detectable wireless signal.

Battery Status

Notifications

Current Time

Right Soft Key Action

There is a weak wireless signal.

There is a good wireless signal.

There is a strong wireless signal.

Phone Notifications — The notification icons alert you of certain events or settings. The following icons may be displayed:

Missed Call. A missed call is listed on the Call List screen.

3-3

Getting Started

New Voicemail. A voicemail has been received, but has not yet been heard.

Details Request. An new request has been received and is listed on the pending Details Request History screen.

Silent. The silent mode is active. No ring tones or alerts will be heard.

Keypad Locked. The keypad is currently locked.

Services Expiry. Your Skype Credit for one or more services is close to expiry.

Headset Attached. The headset is currently attached to the phone.

Skype Online Status — Indicates your current Skype online status. The following states may be displayed:

Online. The normal status when you are signed in to Skype.

Offline. When you are not signed in to Skype.

Do Not Disturb. You can set this status to indicate that you are busy.

Skype Me. Makes your Skype name availalbe for anyone to call.

Away. You can set this status to indicate that you are away.

Not Available. You can set this status to indicate that you are not available to answer calls.

Invisible. Indicates to others that you are offline, but you are still signed in to Skype and can make calls.

Current Time — The current time set on the phone. You can set the phone’s time and date by using the Menu to select “Settings” and then “Time and Date.”

Skype Credit — Your current Skype Credit balance.

Right Soft Key Action — The action that happens when you press the Right Soft

Key. Typically, the Right Soft Key cancels the last action or returns to the previous menu. From the main screen, this provides access to your Contacts.

Left Soft Key Action — The action that happens when you press the Left Soft Key. Typically, the Left Soft Key selects the current menu item or confirms a setting. From the main screen, this provides access to the user menu.

3-4

Understanding the Phone’s LCD Display

The Main Menu

The main menu provides access to all your Skype and phone settings. The menus are easy to move through using the four-way Navigation key. Just move the Navigation key up or down to highlight a menu item, then push down on the key to select it.

The following table outlines the phone menu structure.

Wi-Fi Phone Main Menu

Menu Description

Contacts Your Contacts and their Skype status

History Lists missed calls, incoming and outgoing calls,

Status Sets status and user profile, and signs out

Add Contact Adds a Skype or SkypeOut number to your Contacts

Search Searches for Skype Contacts online

Services Sets up Skype Credit, SkypeIn, and Voicemail

Settings Access to other phone settings

Network Network search, Preferred networks and open network

General Change your Skype password, set auto sign in, and reset

Call divert Records your Voicemail message and changes settings

Privacy Sets Skype privacy settings for calls

Tones Sets the phone’s ring tones and volume

Time and Date Sets the time and date

Manage Blocked Users View current blocked Contacts

Phone Settings Sets the display brightness and contrast, and the display

Information Displays current phone information, including network

Voicemails, and detail requests

connection

the phone

for Voicemail calls

timeout

connection status, software version, and hardware version

3-5

Getting Started

The Power Key Menu

Another menu is available on the phone that provides quick access to power off the phone, change your Skype status, view Wi-Fi netwofk information, and other frequently needed settings.

To access the Power Key menu, press the End/Power key for more than two seconds and then release it. Be sure not to press the key for more than four seconds, which immediately switches the phone off.

The menu lists items depending on your current network connection and Skype sign in status. If you are not connected to a network and not signed in to Skype, only a few menu items are displayed. If you are connected and signed in, the full menu displays.

Wi-Fi Phone Power Key Menu

Menu Description

Switch Off Powers off the phone

Silent Sets the ring tone volume to off

Change Status Changes your Skype online status

My Profile Allows you to change your Skype profile information

Network Information Displays network connection information

Find/View Networks Displays list of detected Wi-Fi networks

Wifi Information Displays Wi-Fi access point information

3-6

Creating a New Skype Account

If you have not previously set up a Skype account, you need to create one before using the phone. When the Skype sign-in screen displays after power on, you are given the option to create a new account.

To creat a new Skype account, follow these steps:

234

1. From the Sign-in option screen, select “Create new account.”

2. Enter a Skype Name for your account. Names must be from 6 to 30

characters.

You can use any mixture of lower or upper case letters, numbers, and punctuation marks. However, you cannot use spaces or start your name with a number or punctuation mark. The [a//A *] key selects upper-case input. The [ 1 ] key selects common punctuation marks, and the [ # ] key allows other symbols to be selected.

A check is made to see if your entered name is already in use by someone else. If the name is already in use, you will have to try another name.

3. Enter a password of between 4 and 20 characters.

You can use any mixture of lower or upper case letters, numbers, and punctuation marks. However, you cannot use spaces or start your name with a number or punctuation mark. Also, you cannot have a password that is the same as your Skype name.

You need to enter your password a second time to confirm it.

4. When your new account has been created, you can sign in and start using

the phone.

See “Setting Up Your Contacts” on page 3-8 and “Making a Call” on page 3-8.

3-7

+ 51 hidden pages