SMC Networks SMC9452TX-2 User Manual

EZ CARD 10/100/1000
EZ Connect N
32-bit 10/100/1000Mbps Gigabit Ethernet PCI Adapter
Draft 11n Wireless USB2.0 Adapter
SMC9452TX-2
Copyright
reliable. However, no responsibility is assumed by SMC for its use, nor for any
infringements of patents or other rights of third parties which may result from its use.
No license is granted by implication or otherwise under any patent or patent rights of
SMC. SMC reserves the right to change specifications at any time without notice.
Copyright © 2008 by
SMC Networks, Inc.
20 Mason
Irvine, CA 92618
All rights reserved. Printed in China
Trademarks
SMC is a registered trademark; and EZ Connect is a trademark of SMC Networks,
Inc. Other product and company names are trademarks or registered trademarks of their
respective holders.
Limited Warranty
Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from
defects in workmanship and materials, under normal use and service, for the applicable
warranty term. All SMC products carry a standard 90-day limited warranty from the date of
purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace
any product not operating as warranted with a similar or functionally equivalent product, during
the applicable warranty term. SMC will endeavor to repair or replace any product returned under
warranty within 30 days of receipt of the product. The standard limited warranty can be
upgraded to a Limited Lifetime* warranty by registering new products within 30 days of purchase
from SMC or its Authorized Reseller. Registration can be accomplished via the enclosed
product registration card or online via the SMC website. Failure to register will not affect the
standard limited warranty. The Limited Lifetime warranty covers a product during the Life of that
Product, which is defined as the period of time during which the product is an “Active” SMC
product. A product is considered to be “Active” while it is listed on the current SMC price list. As
new technologies emerge, older technologies become obsolete and SMC will, at its discretion,
replace an older product in its product line with one that incorporates these newer technologies.
At that point, the obsolete product is discontinued and is no longer an “Active” SMC product. A
list of discontinued products with their respective dates of discontinuance can be found at:
http://www.smc.com/index.cfm?action=customer_service_warranty.
All products that are replaced become the property of SMC. Replacement products may be
either new or reconditioned. Any replaced or repaired product carries either a 30-day limited
warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible for
any custom software or firmware, configuration information, or memory data of Customer
contained in, stored on, or integrated with any products returned to SMC pursuant to any
warranty. Products returned to SMC should have any customer-installed accessory or add-on
components, such as expansion modules, removed prior to returning the product for
replacement. SMC is not responsible for these items if they are returned with the product.
Customers must contact SMC for a Return Material Authorization number prior to returning any
product to SMC. Proof of purchase may be required. Any product returned to SMC without a
valid Return Material Authorization (RMA) number clearly marked on the outside of the package
will be returned to customer at customer’s expense. For warranty claims within North America,
please call our toll-free customer support number at (800) 762-4968. Customers are responsible
for all shipping charges from their facility to SMC. SMC is responsible for return shipping
charges from SMC to customer.
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR
REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER
WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY
OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE UNDER THIS
WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN
THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD
PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING,
UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE
OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR
LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT
OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR
ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES
OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT
APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY
VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO
AFFECT YOUR STATUTORY RIGHTS.
* SMC will provide warranty service for one year following discontinuance from the active
SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans,
and cables are covered by a standard one-year warranty from date of purchase.
SMC Networks, Inc.
20 Mason
Irvine, CA 92618
Compliances
FCC - Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected
Consult the dealer or an experienced radio/TV technician for help
EC Conformance Declaration - Class A
SMC contact for these products in Europe is:
SMC Networks Europe,
Edificio Conata II,
Calle Fructuós Gelabert 6-8, 2o, 4a,
08970 - Sant Joan Despí,
Barcelona, Spain.
This information technology equipment complies with the requirements of the Council
Directive 89/336/EEC on the Approximation of the laws of the Member States relating to
Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain
voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the
compliance with these Directives, the following standards were applied:
RFI Emission:
Limit class A according to EN 55022:1998, IEC 60601-1-2 (EMC, medical)
Limit class A for harmonic current emission according to EN 61000-3-2/1995
Limitation of voltage fluctuation and flicker in low-voltage supply system according to
EN 61000-3-3/1995
Immunity:
Product family standard according to EN 55024:1998
Electrostatic Discharge according to EN 61000-4-2:1995
(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)
Radio-frequency electromagnetic field according to EN 61000-4-3:1996
(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)
Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC
power supply: ±1 kV, Data/Signal lines: ±0.5 kV)
Surge immunity test according to EN 61000-4-5:1995
(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)
Immunity to conducted disturbances, Induced by radio-frequency fields:
EN 61000-4-6:1996 (0.15 - 80 MHz with
1 kHz AM 80% Modulation: 3 V/m)
Power frequency magnetic field immunity test according to
EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)
Voltage dips, short interruptions and voltage variations immunity test
according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%
Reduction @500 ms, >95% Reduction @5000 ms)
LVD
EN 60950-1:2001
Please read the following safety information carefully before installing the device:
WARNING: Installation and removal of the unit must be carried out by
qualified personnel only.
This guide is intended for use by network administrators who are
responsible for setting up and installing network equipment;
consequently it assumes a basic working knowledge of LANs (Local Area Networks).
The unit must be connected to an earthed (grounded) outlet to comply with international safety standards.
Do not connect the unit to an A.C. outlet (power supply) without an
earth (ground) connection.
The appliance coupler (the connector to the unit and not the wall plug)
must have a configuration for mating with an EN 60320/IEC 320
appliance inlet.
The socket outlet must be near to the unit and easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet.
This unit operates under SELV (Safety Extra Low Voltage) conditions
according to IEC 60950. The conditions are only maintained if the
equipment to which it is connected also operates under SELV
conditions.
Veuillez lire à fond l’information de la sécurité suivante avant d’installer le Device: AVERTISSEMENT: L.installation et la dépose de ce groupe doivent être
confiés à un personnel qualifié.
Ne branchez pas votre appareil sur une prise secteur (alimentation
électrique) lorsqu’il n’y a pas de connexion de mise à la terre (mise à la
masse).
Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité.
Le coupleur d.appareil (le connecteur du groupe et non pas la prise
murale) doit respecter une configuration qui permet un branchement sur une entrée
d.appareil EN 60320/IEC 320.
La prise secteur doit se trouver à proximité de l.appareil et son accès doit être facile. Vous ne pouvez mettre l.appareil hors circuit qu.en
débranchant son cordon électrique au niveau de cette prise.
L.appareil fonctionne à une tension extrêmement basse de sécurité qui
est conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si
l.équipement auquel il est raccordé fonctionne dans les mêmes conditions.
Bitte unbedingt vor dem Einbauen des RPU die folgenden Sicherheitsanweisungen durchlesen:
WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch
Fachpersonal erfolgen.
Diese Anleitung ist fr die Benutzung durch Netzwerkadministratoren
vorgesehen, die fr die Installation und das einstellen von
Netzwerkkomponenten verantwortlich sind; sie setzt Erfahrung bei der Arbeit mit LANs
(Local Area Networks) voraus.
Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose
angeschlossen werden.
Das Gerät muß an eine geerdete Steckdose angeschlossen werden,
welche die internationalen Sicherheitsnormen erfüllt.
Der Gerätestecker (der Anschluß an das Gerät, nicht der
Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320
konfigurierten Geräteeingang haben.
Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich
sein. Die Stromversorgung des Geräts kann nur durch Herausziehen des
Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.
Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen
(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind
nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter
SELV-Bedingungen betrieben werden
Stromkabel. Dies muss von dem Land, in dem es
benutzt wird geprüft werden:
Schweiz
Europe
Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen ein- halten.
Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestan-
forderung) sein und die Aufschrift <HAR>
oder <BASEC> tragen
Der Netzstecker muß die Norm CEE 7/7
erfüllen (.SCHUKO.).
Warnings and Cautionary Messages
Warning: This product does not contain any serviceable user parts. Warning: Installation and removal of the unit must be carried out by qualified personnel
only.
Warning: When connecting this device to a power outlet, connect the field ground lead
on the tri-pole power plug to a valid earth ground line to prevent electrical
hazards.
Caution: Wear an anti-static wrist strap or take other suitable measures to prevent
electrostatic discharge when handling this equipment.
Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this
device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!
Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC
standards.
Warnings (in German)
Achtung: Dieses Produkt enthält keine Teile, die eine Wartung vom Benutzer benötigen.
Achtung: Installation und Deinstallation des Gerätes müssen von qualifiziertem
Servicepersonal durchgeführt werden.
Achtung: Wenn das Gerät an eine Steckdose angeschlossen wird, muß der Masseanschluß
n Netzstecker mit Schutzerde verbunden werden, um elektrische
Gefahren zu vermeiden.
Environmental Statement
The manufacturer of this product endeavours to sustain an environmentally-friendly policy
throughout the entire production process. This is achieved though the following means:
Adherence to national legislation and regulations on environmental production standards.
Conservation of operational resources.
Waste reduction and safe disposal of all harmful un-recyclable by-products.
Recycling of all reusable waste content.
Design of products to maximize recyclables at the end of the product.s life span.
Continual monitoring of safety standards.
End of Product Life Span
This product is manufactured in such a way as to allow for the recovery and disposal of all
included electrical components once the product has reached the end of its life.
Manufacturing Materials
There are no hazardous nor ozone-depleting materials in this product.
Documentation
All printed documentation for this product uses biodegradable paper that originates from
sustained and managed forests. The inks used in the printing process are non-toxic.
Purpose
This guide details the hardware features of the product, including Its physical and
performance-related characteristics, and how to install the product.
Audience
The guide is intended for use by network administrators who are responsible for installing and
setting up network equipment; consequently, it assumes a basic working knowledge of LANs
(Local Area Networks).
Diese Anleitung ist für die Benutzung durch Netzwerkadministratoren vorgesehen, die für die
Installation und das einstellen von Netzwerkkomponenten verantwortlich sind; sie setzt
Erfahrung bei der Arbeit mit LANs (Local Area Networks) voraus.
Package Contents
The following items should be found in your box:
¾ One 10/100/1000Mbps Gigabit Ethernet PC Adapter
¾ One Resource CD, including
Drivers
User Guide
Other Helpful Information
Note:
)
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact with your distributor for assistance.
CONTENT
Chapter 1. Introduction............................................................................................ 1
1.1 Convention ......................................................................................................... 1
1.2 Product Overview ............................................................................................... 1
1.3 Main Features .................................................................................................... 2
1.4 LED Status ......................................................................................................... 2
Chapter 2. Installation .............................................................................................3
2.1 Hardware Installation.......................................................................................... 3
2.2 Software Installation ........................................................................................... 4
2.2.1 Install driver for XP................................................................................................ 4
2.2.2 Update driver for XP ...........................................................................................11
2.2.3 Update driver for Vista ........................................................................................18
2.3 Enable Wake on LAN function ......................................................................... 25
Appendix A: Specifications................................................................................... 28
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide

Chapter 1. Introduction

Thank you for choosing SMC9452TX-2 Gigabit PCI Ethernet Adapter.

1.1 Convention

The Adapter or SMC9452TX-2 mentioned in this User Guide stands for SMC9452TX-2 Gigabit
PCI Ethernet Adapter.

1.2 Product Overview

SMC9452TX-2 is a highly integrated and cost-effective single-chip Gigabit Ethernet Adapter that
provides 32-bit performance, PCI bus master capability, and full compliance with IEEE 802.3
10Base-T, IEEE802.3u 100Base-TX and IEEE 802.3ab 1000Base-T specifications. It also
supports ACPI, PCI power management for modern operating systems that are capable of
Operating System Directed Power Management (OSPM) to achieve the most efficient power
management.
Through the aid of a VLAN membership, SMC9452TX-2 adheres to the 802.1Q for multiple VLAN
support, and 802.1P for packet prioritization. With 802.1Q support, server resources can be
shared with multiple VLANs when used in conjunction with any 802.1Q-enabled Switch. With the
802.1p support, SMC9452TX-2 allows a range of Ethernet packets to be prioritized from a critical
to a non-critical designation through a priority tag.
SMC9452TX-2 supports Full Duplex operations at 20/200/2000 Mbps data speeds used in
conjunction with 802.3x flow control support. With 802.3x flow control SMC9452TX-2 uses both
asymmetric and symmetric functions via the MAC control pause function. Any participating 802.3x
flow control node can be controlled by initiating a pause control to stop incoming network traffic, to
further reduce network congestion. SMC9452TX-2 also supports the WOL (Wake on LAN)
Function which allows a remote station “wake” your computer when it is in Standby or Hibernate
mode or after shutdown.
By default SMC9452TX-2 supports the standard 1518 Byte frame size. In addition, SMC9452TX-2
also supports Jumbo Frame transmission
It includes an interface for a boot ROM and can be used in diskless workstations, providing
maximum network security and ease of management.
In addition, being PCI 2.2 compliant, SMC9452TX-2 works with 32-bit 33Mhz PCI busses. This
compatibility provides users with an easy migration path to increase performance between
servers and workstations for large file transfer, video editing and server clustering for data
intensive applications.
1
Loading...
+ 28 hidden pages