SMC Networks SMC9452TX-1 User Manual

Copyrights
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice.
Copyright © 2005 by
38 Tesla
Irvine, CA 92618
All rights reserved.
Trademarks:
SMC is a registered trademark; and EZ Card, is a trademark of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders.
1
Contents
Warranty …………………………………………………….…..………..…...... 3
Compliances ……………………………..……………………………………. 5
Hardware Description ................................................................................….. 7
Package Contents …………………………………………………….…….… 7
Hardware Installation ……….……………………………………….………. 8
Driver Installation …………………………………………..………..……… 10
Windows 9x ………..………….……………………….……………….…… 10 Windows ME ……….……………….……………………………….………. 14 Windows NT ……….………………….…………………………….……….. 16 Windows 2000 ………...…………………….…………………….….……… 17 Windows XP ……………………………………….………..……………….. 18
Driver Verification ……………………..……………………………………. 24
Troubleshooting ……………….……………………………………………. 27
Cable Types and Specifications ……………..…………………………… 29
Technical Specifications ..………………………………………………..… 30
Terminology …….……………………………………………………….…… 32
2
Limited Warranty
Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term. SMC will endeavor to repair or replace any product returned under warranty within 30 days of receipt of the product.
The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering new products within 30 days of purchase from SMC or its Authorized Reseller. Registration can be accomplished via the enclosed product registration card or online via the SMC web site. Failure to register will not affect the standard limited warranty. The Limited Lifetime warranty covers a product during the Life of that Product, which is defined as the period of time during which the product is an ‘Active’ SMC product. A product is considered to be ‘Active’ while it is listed on the current SMC price list. As new technologies emerge, older technologies become obsolete and SMC will, at its discretion, replace an older product in its product line with one that incorporates these newer technologies. At that point, the obsolete product is discontinued and is no longer an ‘Active’ SMC product.
All products that are replaced become the property of SMC. Replacement products may be either new or reconditioned. Any replaced or repaired product carries either a 30-day limited warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible for any custom software or firmware, configuration information, or memory data of Customer contained in, stored on, or integrated with any products returned to SMC pursuant to any warranty. Products returned to SMC should have any customer-installed accessory or add-on components, such as expansion modules, removed prior to returning the product for replacement. SMC is not responsible for these items if they are returned with the product.
Customers must contact SMC for a Return Material Authorization number prior to returning any product to SMC. Proof of purchase may be required. Any product returned to SMC without a valid Return Material Authorization (RMA) number clearly marked on the outside of the package will be returned to customer at customer’s expense. For warranty claims within North America, please call our toll-free customer support number at (800) 762-4968. Customers are responsible for all shipping charges from their facility to SMC. SMC is responsible for return shipping charges from SMC to customer.
3
Limited Warranty
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.*
SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase.
4
Compliances
FCC - Class A
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV technician for help
EC Conformance Declaration - Class B
SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II, Calle Fructuós Gelabert 6-8, 2o, 4a, 08970 - Sant Joan Despí, Barcelona, Spain.
This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:
RFI Emission:
Limit class B according to EN55022:1998
Limit class B for harmonic current emission according to EN61000-3-2/1995
Limitation of voltage fluctuation and flicker in low-voltage supply system according to
EN61000-3-3/1995
Immunity:
Product family standard according to EN55024:1998
Electrostatic Discharge according to EN61000-4-2:1995 (Contact Discharge: ±4 kV, Air
Discharge: ±8 kV)
Radio-frequency electromagnetic field according to EN61000-4-3:1996 (80 - 1000 MHz with
1 kHz AM 80% Modulation: 3 V/m)
Electrical fast transient/burst according to EN61000-4-4:1995 (AC/DC power supply: ±1 kV,
Data/Signal lines: ±0.5 kV)
Surge immunity test according to EN61000-4-5:1995 (AC/DC Line to Line: ±1 kV, AC/DC
Line to Earth: ±2 kV)
5
Immunity to conducted disturbances, Induced by radio-frequency fields: EN61000-4-6:1996
(0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m)
Power frequency magnetic field immunity test according to EN61000-4-8:1993 (1 A/m at
frequency 50 Hz)
Voltage dips, short interruptions and voltage variations immunity test according to EN61000-
4-11:1994 (>95% Reduction @10 ms, 30% Reduction @500 ms, >95% Reduction @5000 ms)
LVD
EN60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)
Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Les raccordeurs ne sont pas utilisé pour le systéme téléphonique!
Industry Canada - Class B
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des Communications.
Japan VCCI Class B
Australia AS/NZS 3548 (1995) - Class B
6
Hardware Description
SMC’s EZ Card 1000, SMC9452TX-1, is a Gigabit Ethernet network interface card for 32-bit PCI local bus­compliant computers. It operates under the 1000BASE-T specification over Category 5 UTP Cable, as well as being compatible with 100BASE-TX and 10BASE-T connections. This network card provides up to ten times the bandwidth of Fast Ethernet, and can deliver a full 2 Gbps of throughput to the host PC. A true plug-and-play device, the card is auto-configurable upon power up. Leading-edge ASIC technology and performance­enhancing techniques maximize throughput and minimize CPU utilization. It also supports full- and half-duplex and features auto-negotiation.
1 RJ-45 connector for 10/100/1000 Mbps connections
1 Socket for Optional Boot ROM
2 LED Indicators – Link/ACT, FD (Full Duplex)
Package Contents
After unpacking the EZ Card 1000, check the contents of the box to be sure you have received the following components:
EZ Card 1000 network card SMC9452TX-1
Quick Install Guide
Driver & Documentation CD containing this User Guide and Drivers
SMC Warranty Registration Card
Immediately inform your dealer in the event of any incorrect, missing or damaged parts. If possible, please retain the carton and original packing materials in case there is a need to return the product. Please fill out and return the Warranty Registration Card to SMC or you may register the product on SMC’s Web site. The EZ Card 1000 is covered by a limited lifetime warranty.
7
System Requirements
Before you install the EZ Card 1000, check your system for the following requirements:
A PC and BIOS that support the PCI Local Bus Specification v2.0 or later
An available 32-bit PCI slot
Category 5 or 5e UTP cable with RJ-45 connectors
An IEEE 802.3ab-compliant Gigabit Ethernet device installed in your network
Note: If you are installing in an older PC model (Pentium or earlier), upgrade the BIOS to the latest version.
Hardware Installation
WARNINGS:
This network adapter requires a PC and BIOS that support the PCI Local Bus Specification
v2.0 or later. If you are installing in an older PC model, upgrade the BIOS to the latest version.
Network cards are sensitive to static electricity. To protect the card, avoid touching its
electrical components and always touch the metal chassis of your computer before handling the card.
1. Switch off the computer, unplug the power cord, and remove the computer’s cover.
2. Select an available PCI slot and remove the cover bracket.
- When using a 32-bit PCI slot, the end of the card’s edge connector will be exposed. Be
careful that it does not touch any conducting parts on the PC motherboard.
3. Install the network card into the slot so that it is firmly seated. Then screw the card’s bracket
securely into the PC’s chassis.
4. Replace the chassis cover and power up your PC.
5. The EZ Card 1000 should be automatically configured by the host computer’s BIOS. However,
if you have an older computer, you may have to manually configure the computer’s BIOS settings (see “Troubleshooting”).
6. The Driver & Documentation CD that accompanies the EZ Card 1000 contains all the network
operating system drivers supported by this card. Please read the “RELEASE.TXT” file on the CD for a list of all drivers. Refer to following sections on this manual for instructions on installing drivers. Any new or updated drivers can be downloaded from SMC’s Web site (WWW.SMC.COM).
8
PCI Configuration
In most cases, your network card is automatically configured when you power-up your computer. In certain computers, however, you must modify PCI settings by running your computer’s BIOS Setup program. For more information, refer to “PCI Compatibility” section of this manual.
Connecting Category 5 Cable
To connect to a 1000BASE-T Gigabit Ethernet device, use the RJ-45 connector on the network card and Category 5, 5e or better UTP cable. This connection can be made directly to the device, or indirectly via a wall outlet that has the proper wiring for an RJ-45 connector. Connections can be made for a distance of 100m (328 ft). It is recommended that for all critical connections, or any new cable installations, Category 5e (enhanced Category 5) cable should be used.
Connecting UTP Cable
1. Attach the male RJ-45 connector on one end of a UTP cable to the network card’s RJ-45 port.
2. Attach the male connector on the other end of the UTP cable directly to an Ethernet, Fast
Ethernet or Gigabit Ethernet device. OR, attach the male connector on the other end of the UTP cable to a wall outlet with an RJ-45 connector properly wired for 1000BASE-T Gigabit Ethernet. Wiring from the wall outlet connection is usually routed to a hub or switch through a punch-down block located in a wiring closet.
3. For 1000 Mbps operation, make certain that the device you are connecting to is compliant
with IEEE 802.3ab 1000BASE-T.
9
Driver Installation
Windows 95/98
NOTE: Installation processes will require the use of your original, licensed copy of Windows. Please have your Windows CD available BEFORE proceeding with the installation.
Step 1: After you have inserted the EZ Card 10/100/1000 SMC9452TX-1 PCI Card in your machine, the Operating System will automatically recognize the adapter and prompt you for the appropriate drivers. Click the [Next >] button to begin the installation.
Step 2: Insert the Driver CD and select the [Search for the best driver for your device] option and click [Next >]. In Windows 95, you may be immediately asked to enter the path of the driver location. Type ?:\SMC9452\WIN95. (Note: The "?" equals the letter of your CD-ROM drive. In most cases, this is D.)
10
Loading...
+ 25 hidden pages