SMC Networks RT539222SB24 User Manual

JI5-RT539222SB24

User Manual

802.11 b/g/n Wireless Mini PCIE

SMC Networks

20 Mason

Irvine, CA 92618

U.S.A.

Copyright © 2013 SMC Networks

All Rights Reserved

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no
responsibility is assumed by SMC for its use, or for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or otherwise under any patent or patent rights
of SMC. SMC reserves the right to change specifications at any time without notice

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or stored in a database or retrieval system for any purpose
without the express written permission of SMC.

Microsoft and Windows are registered trademarks of Microsoft Corporation. Apple and Macintosh are registered
trademarks of Apple, Inc. All other brands, product names, trademarks, or service marks are property of their
respective owners.

ii

SMCD3GNV5 Administrator Manual

Compliance

Federal

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Communication Commission

Interference

Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.

iii

SMCD3GNV5 Administrator Manual

IMPORTANT NOTE:

FCC

Radiation Exposure St

atement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.

This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.

IEEE 802.11b/g/n operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.
This device is

intended

only for OEM

integrators

under the

following conditions:

 The antenna must be installed such that 20 cm is maintained between the antenna and users, and
 The transmitter module may not be co-located with any other transmitter or antenna.

As long as the above two conditions are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC peripheral
requirements, etc.).

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining
a separate FCC authorization.

注意 !

依據
第十二條
自變更頻率、加大功率或變更原設計之特性及功能。

低功率電波輻射性電機管理辦法

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用 者均不得擅

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現 有干擾現象
時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信規定作業之無線
電信。低功率射頻電機 須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干 擾。

iv

SMCD3GNV5 Administrator Manual