SMC Networks LLB4, LLB3 Operation Manual
Doc. No LV20***-OMK0003-A .
PRODUCT NAME
CLAEAN AIR MODULE
CLAEAN AIR MODULECLAEAN AIR MODULE
CLAEAN AIR MODULE
MODEL / Series / Product Number
LLB Series
LLB SeriesLLB Series
LLB Series
2
Contents
1. Safety Instructions ・・・・・・・・・・・・・・・・・・・・・・・・・P3～4
2. Clean Air Module / Precautions ・・・・・・・・・・・・・・・・・・・・P5～6
3. Specific Product Precautions・・・・・・・・・・・・・・・・・・・・・P7～10
4. Variations ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P11
5. Specifications・・・・・・・・・・・・・・・・・・・・・・・・・・・・P12～13
6． Flow-rate Characteristics・・・・・・・・・・・・・・・・・・・・・・・P14
7. Digital Flow Switch Output Specifications ・・・・・・・・・・・・・・・P15
8. Functions ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P16
9. Additional Module Procedure ・・・・・・・・・・・・・・・・・・・・P17
10. Element Replacing Procedure ・・・・・・・・・・・・・・・・・・・・P18
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
“Danger.”
They are all important
(ISO/IEC)
*1)
*1) ISO 4414:
ISO 4413:
IEC 60204
ISO 102
18
etc.
Caution
Warning
Danger
1. The compatibility of the product is the responsibility of the person who designs the
equipment or decides its
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
necessary analysis and tes
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referr
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
equipment.
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove pr
confirmed.
1.
The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
2.
When the product is to be
and the power from any appropriate source is cut, and read and understand the specific product
precautions
of all relevant products carefully.
3.
Before machinery/equipment is
4. Contact SMC beforehand and take special consideration of safety measures if the product is
to be used in any of the following conditions.
1.
Conditions and environments outside o
direct sunlight.
2.
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recrea
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
3.
An application which could have negative effects on people, property, or animals requiring special safety
analysis.
4.
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
mechanical protective funct
, and other safety regulations.
Pneumatic fluid power
Hydraulic fluid power
-1:
Safety of machinery
-1992:
Manipulating industrial robots
Safety Instructions
notes for safety and must be followed in addition to International Standards
--
General rules relating to systems
--
General rules relating
--
Caution
in minor or
Warning
result in
death or serious injury.
Danger
in death
or
specifications.
t results.
here may become unsafe if handled incorrectly.
removed, confirm that the safety measures as mentioned above are implemented
ion, and periodical checks to confirm proper operation.
Electrical equipment of machines
-
Safety.
indicates a hazard with a low level of risk which, if not avoided, could result
mode
rate injury.
indicates a hazard with a
indicates a hazard with a
serious
injury.
restarted, take measures to prevent unexpected operation and malfunction.
f the given specifications, or use outdoors or in a place exposed to
3
to systems
Warning
oduct and machinery/equipment until safety is
.
.
.
(Part 1:
medium
level of risk which, if not avoided, could
high
level of risk which, if not avoided,
tion, or equipment in contact with food and
General requirements)
ing to its latest catalog
will
result
1.
The product is provided for use in
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
Requirements”.
Read and accept them before
Limited warranty and Disclaimer
1.
The warranty period of
delivered
Also, the product may have specified
Please
consult your nearest sales branch.
2.
For any failure or damage reported within the warranty period which is clearly our
responsibility,
a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
3.
Prior to using SMC products, please read and understand the warranty terms and
disclaimers
noted in the specified
∗∗∗∗2)
Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to
pad or failure due to the deterioration of rubber material are not covered by the limited
warranty.
Compliance Requirements
1.
The use of SMC products with production equipment for the manufacture of weapons of
mass destruction(WMD)
2.
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to the shipment of a SMC product
that export are known and f
,whichever is first
Safety Instructions
using the product.
the product is 1 year in service or 1.5 years after the product is
.
∗∗∗∗
catalog for the particular products.
or any other weapon is strictly prohibited.
manufacturing industries.
2)
to another country, assure that all local rules goveming
ollowed.
ollowed.ollowed.
ollowed.
4
Caution
durability, running distance or replacement parts.
the use of the vacuum
5
6
Loading...