SMC Networks LEC-W2-U,LEC-W2A-C Operation Manual

No.JXC※-OMX0002

PRODUCT NAME

Communication cable for controller setting kit

MODEL / Series / Product Number

LEC-W2A-C

-1-

No.JXC※-OMX0002

Contents

1. Safety Instructions 2

2. Outline 4

3. Installation of driver 5

3.1 Automatic Installation 5

3.2 Manual Installation 6

4. ACT Controller Installation 10

4.1 Installation 10

4.2 Check of the Communication Port 10

4.3 Communication Setting 11

4.4 Functions of Each Mode 12

-2-

No.JXC※-OMX0002

Controller Setting Kit

1. Safety Instructions

These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.”
They are all important notes for safety and must be followed in addition to International Standards
(ISO/IEC)*1) , and other safety regulations.

*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems.

ISO 4413: Hydraulic fluid power -- General rules relating to systems.
IEC 60204-1: Safety of machinery -- Electrical equipment of machines .(Part 1: General requirements)
ISO 10218: Manipulating industrial robots -Safety.
etc.

Caution

Caution indicates a hazard with a low level of risk which, if not avoided, could result

in minor or moderate injury.

Warning

Warning indicates a hazard with a medium level of risk which, if not avoided, could

result in death or serious injury.

Danger

Danger indicates a hazard with a high level of risk which, if not avoided, will result

in death or serious injury.

Warning

1. The compatibility of the product is the responsibility of the person who designs the equipment or
decides its specifications.

Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest catalog
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
equipment.

2. Only personnel with appropriate training should operate machinery and equipment.

The product specified here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.

3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed.

1.The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.

2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product precautions
of all relevant products carefully.

3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.

4. Contact SMC beforehand and take special consideration of safety measures if the product is to be used
in any of the following conditions.

1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to
direct sunlight.

2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,

vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.

3. An application which could have negative effects on people, property, or animals requiring special safety

analysis.

4.Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a

mechanical protective function, and periodical checks to confirm proper operation.

-3-

No.JXC※-OMX0002

Controller Setting Kit
Safety Instructions

Caution

The product is provided for use in manufacturing industries.

The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange specifications or a
contract if necessary.
If anything is unclear, contact your nearest sales branch.

Limited warranty and Disclaimer/Compliance Requirements

The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
Requirements”.

Read and accept them before using the product.

Limited warranty and Disclaimer

1. Grant of license

1. This Software is to be used in accordance with this Agreement non-exclusively for the limited purpose of

writing data to controllers for SMC electrical actuators.

2. This software can be installed and saved on a PC for the sole purpose specified in the preceding
paragraph.

2. Restrictions

1. This software is not to be copied, except as specified in Article 1-2.

2. This software license is not to be transferred or lent wholly or in part to a third party, either free of charge
or for payment.

3. Modification, translation, adaptation or reverse engineering of this software is not permitted.

3. Precautions

1. Read the "Safety Instructions", "Precautions", "Specific Product Precautions" and "Specifications"
described in the manual for the equipment when using any equipment controlled by this software.

2. This Software and the equipment controlled by it are subject to change without prior notice.

4. Exemption of liability

1. SMC cannot take any responsibility for any damage incurred by the use of the controller to which the
data is written by this Software.

2. SMC cannot take any responsibility for any damage incurred by the use of this software.

5. Termination

1. SMC has the full authority to terminate this agreement in the event of any terms and conditions have
been breached.

2. This software and any copies thereof must be destroyed when this agreement is terminated.

6. Rights of this Software

The copyright and any other rights of this Software are owned by SMC, and protected by Japanese
copyright laws and international treaty provisions.

-4-

No.JXC※-OMX0002

2. Outline

The communication cable (LEC-W2A-C) is used to connect the electric actuator controller (LECP series,
LECA series, JXC□1 series) and PC and helps communication between those devices using the controller
setting software (ACT Controller).

Product specifications

Applicable controllers

LECP6, LECA6, LECPA, LECPMJ
JXC□1

*1)

Applicable USB cables

LEC-W2-U

*2)

Operating
environment

OS

Windows®10, Windows®8.1, Windows®7

Communication interface

USB1.1 or USB2.0 port

*1) Do not connect the cable to devices other than the applicable controllers.

When connecting the communication cable to the JXC□1 series, use a conversion cable.

Conversion cable No.: P5062-5

*2) Prepare a USB cable (A-miniB) LEC-W2-U to connect the communication cable and PC separately.

Caution

The communication setting cable (LEC-W2A-C) is a dedicated cable for the applicable controllers.

- The cable connected to the controllers is different from the LAN cable. Therefore, if the communication
cable is connected to the LAN connector, the LAN connector might be broken.

- For the LECP and LECA series, connect the communication cable to the communication connector
(CN4).

- For the JXC□1 series, connect the communication cable to the communication connector (SI) via a
conversion cable (P5062-5). (It is not possible to directly connect the communication cable to the
communication connector).

Communication cable

LEC-W2A-C

USB cable
LEC-W2-U

*2)

- Controller setting software (ACT Controller)

- USB driver
Please download from SMC website.
https://www.smcworld.com

Electric actuator

Controller

PC