SMC Networks KER25U INSTALLATION GUIDE
LED Indicative
Color
Status
Description
Light off
Power off
Solid Light
Link successfully
Blinking
Data transmitting
Light off
Link off
Solid Light
Link successfully
Blinking
Data transmitting
Solid Light
Negotiation is in progress under
Solid Light
Wireless On
Blinking
Data transmitting
Light off
Wireless Off
Solid Light
Wireless On
Blinking
Data transmitting
Light off
Wireless Off
Quaick Installation Guide
Wireless Dual Band Router
KER25U
Product Brief
Front Panel
This product is specially designed to satisfy all your wireless
demand at home, office, and small business. It’s not only
with practical functions and excellent performance, but also
easy management.
KER25U is a multi-functional network product combined
with dual band AP, 4-port switch, and NAT router, and
complied with IEEE 802.11ac with up to 867Mbps speeds.
Meanwhile, it downward complied with IEEE 802.11a/b/n.
Package Contents
One ECW5350 Wireless Dual Band Router
One 12V DC Adaptor
One Quick Installation Guide
One RJ-45 Ethernet Cable
Back Panel
POWER (PWR)
WAN
LAN 1-4
Green
Green
Green
WPS
WLAN 2.4G Green
Green
1-1
Solid Light
Light off Link off
(one minute)
Blinking
1-2
Power on
Connection succeeded under WPS
WPS
Port Function
WAN Wide Area Network port; Connect with Ethernet cable to a local
area network such as xDSL/Cable Modem or LAN network
LAN
Local Area Network port; Connect with Computer Lan card or
1-4
other Ethernet network devices
USB USB 2.0 port; Connect with USB device
WPS Wi-Fi Protected Setup; Press WPS button till WPS blinking as
negotiation with LAN card successfully, then WPS LED light goes
off. If negotiation with LAN card fails, WPS will also go off.
DC-IN Power jack; Connect with power outlet to supply power to the
router. (To avoid the risk of damage the router, please do not use
power adaptor not packaged with the router.)
WLAN 5G Green
Connect Your World
Switches | Wireless | Broadband | Carrier Ethernet | Network Management
www.smc.com
www.smc asia.com
-
Installation
Set up WAN Connection
Plug Ethernet cable to WAN port of KER25U, and the other side of cable to xDSL/Cable
Modem or LAN network
2-1
Set up LAN Connection
Plug another Ethernet cable (not included) to your computer or other Ethernet network
devices, and the other side of Ethernet cable to any of LAN 1 to LAN4 on KER25U
Power on the Router
Connect power jack of power adaptor to the router, and plug the power adaptor into an
outlet. KER25U will be power on automatically and ready for your use.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
When suing IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15 to 5.25GHz frequency range. The FCC requires this product to be
used indoors for the frequency range of 5.15 to 5.25GHz to reduce the potential for harmful interference to co channel mobile satellite systems.
High-power radar is allocated as the primary user of the 5.25 to 5.35GHz and 5.65 to 5.85GHz bands. These radar stations can cause interference with and/or damage to this
device.
Connect Your World
Switches | Wireless | Broadband | Carrier Ethernet | Network Management
www.smc.com
www.smc asia.com
-
Loading...