SMC Networks ITVX Series, ITVX2030-0 Series, ITVX2030-1 Series, ITVX2030-2 Series, ITVX2030-3 Series Operation Manual

Doc. No. DII-63400-OM002-C

Install and operate the product only after reading the Operation Manual carefully and

This product does not have sufficient control for applications

P R O D U C T N A M E

High Pressure E/P Regulator

MODEL/ Series/ Product Number

ITVX Series

●

understanding its contents.

●

Specifically, read the safety instructions carefully.

●

Keep this operation manual available whenever necessary.

●

This product is only for blowing.

other than blowing (driving, sealing etc.).

Contents

Contents P1

Safety Instructions P2

Handling precautions P4

Wiring method P6

Setting method P8

Key locking function P9

Setting of min. pressure, max. pressure and switch output P10

Mode of switch output P11

Reset function P12

Error indicating function P12

Detail setting mode P13

Gain setting P13

Zero clear P14

Initialize P15

LED display P15

- 1 -

High Pressure E/P Regulator
Safety Instructions

These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.”
They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC)
and other safety regulations.

*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems.

ISO 4413: Hydraulic fluid power -- General rules relating to systems.
IEC 60204-1: Safety of machinery -- Electrical equipment of machines .(Part 1: General requirements)
ISO 10218-1992: Manipulating industrial robots -Safety.

etc.

*1)

,

Caution

Warning

Danger

Caution

in minor or moderate injury.

Warning

result in death or serious injury.

Danger

in death or serious injury.

indicates a hazard with a low level of risk which, if not avoided, could result

indicates a hazard with a medium level of risk which, if not avoided, could

indicates a hazard with a high level of risk which, if not avoided, will result

Warning

1. The compatibility of the product is the responsibility of the person who designs the equipment or
decides its specifications.

Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest catalog
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
equipment.

2. Only personnel with appropriate training should operate machinery and equipment.

The product specified here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be performed
by an operator who is appropriately trained and experienced.

3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed.

1.The inspection and maintenance of machinery/equipment should only be performed after measures to

prevent falling or runaway of the driven objects have been confirmed.

2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product precautions
of all relevant products carefully.

3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.

4. Contact SMC beforehand and take special consideration of safety measures if the product is to be
used in any of the following conditions.

1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to
direct sunlight.

2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,

vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.

3. An application which could have negative effects on people, property, or animals requiring special safety

analysis.

- 2 -

4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a

mechanical protective function, and periodical checks to confirm proper operation.

High Pressure E/P Regulator
Safety Instructions

Caution

1. The product is provided for use in manufacturing industries.

The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange specifications
or a contract if necessary.
If anything is unclear, contact your nearest sales branch.

Limited warranty and Disclaimer/Compliance Requirements

The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
Requirements”.
Read and accept them before using the product.

Limited warranty and Disclaimer

1.The warranty period of the product is 1 year in service or 1.5 years after the product is delivered,
whichever is first.∗∗∗∗2)
Also, the product may have specified durability, running distance or replacement parts. Please
consult your nearest sales branch.

2. For any failure or damage reported within the warranty period which is clearly our responsibility,

a replacement product or necessary parts will be provided.

This limited warranty applies only to our product independently, and not to any other damage

incurred due to the failure of the product.

3. Prior to using SMC products, please read and understand the warranty terms and disclaimers
noted in the specified catalog for the particular products.

∗∗∗∗2)

Vacuum pads are excluded from this 1 year warranty.

A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.

Also, even within the warranty period, the wear of a product due to the use of the vacuum

pad or failure due to the deterioration of rubber material are not covered by the limited

warranty.

Compliance Requirements

1. The use of SMC products with production equipment for the manufacture of weapons of mass

destruction (WMD) or any other weapon is strictly prohibited.

2. The exports of SMC products or technology from one country to another are governed by the

relevant security laws and regulation of the countries involved in the transaction. Prior to the
shipment of a SMC product to another country, assure that all local rules governing that export
are known and followed.

- 3 -

Warning

If oxygen is used as the fluid, it can lead to serious and unforeseen risks. However, it is possible to
manage and control the risk of hazards and economic loss. In order to use the product safely, it
should only be handled by personnel with appropriate knowledge, with support from a suitably
qualified specialist.
Oxygen gas increases the susceptibility of substances to burning, can be ignited by frictional heat
and static electricity, and makes metal and seal materials burn. Therefore, flush the piping thoroughly
and mount a suitable filter to prevent foreign matter such as metal powder and dust from entering the
product.
Take safety measures by installing safety devices (e.g. a circuit that stops the supply of oxygen gas)
to prevent fire and explosion in the event of failure, taking flameproof safety standards into
consideration.
Since there is an exhaust port on the product, connect the piping in order to exhaust oxygen.
Do not block the exhaust port.

Handling precautions

,

！！！！

Caution

△△△△

If the power supply to this product is turned off due
to a power failure during normal operation, the
output on the secondary side will be held and air will
flow continuously.

- 4 -

If supply pressure to this product is interrupted or
shut off, while the power is still on, the internal
solenoid valve will continue to operate and a
humming noise will be generated.
Turn off the power supply when supply pressure is
interrupted or shut off, since the life of the product
may be shortened.

The optional cable connector is a 4 wire type.
When the monitor output (analogue output or switch
output) is not being used, prevent the unused wires
from touching the other wires, as a malfunction
could occur.

,

！！！！

Caution

△△△△

This product is adjusted to specification at the time
of shipment from the factory.
Avoid careless disassembly or removal of parts, as
this can lead to malfunction.

- 5 -