SMC Networks EZ1026DT, EZ1026FMSC, EZ1026GLSC, EZ1026GSSC, EZ1026GT User Manual

SMC-EZ1026DT V.2

1

SMC-1026DT V.2

Unmanaged

Ethernet/Fast Ethernet

Switch

User Guide

EZ Switch 10/100

SMC-EZ1026DT V.2

2

Table of Contents

1. Introduction ................................................................. 3

1.1 Features ............................................................................. 4

1.2 Package Contents ..............................................................5

2. Hardware Description.................................................... 6

2.1 Hardware Description......................................................... 6

The Front Panel .............................................................................6

10/100Base-TX RJ-45 ports (Auto MDI/MDIX ):.............................7

Expansion Slots: ............................................................................7

Console Port: .................................................................................7

2.2 LED Indicators....................................................................7

Rear Panel ..................................................................................... 8

Power On ....................................................................................... 9

3. Connecting to the Network............................................ 9

3.1 Pre-Installation Requirements ............................................9

3.2 Mounting the Switch ......................................................... 10

Desktop Mounting ........................................................................10

Rack-mounted Installation............................................................ 11

3.3 Connecting to the Switch.................................................. 12

3.4 Login in the Console Interface.......................................... 13

4. Network Configuration................................................. 21

4.1 Collapsed Backbone Application...................................... 21

4.2 Departmental Bridge ........................................................22

4.3 High Performance Switched Workgroup .......................... 23

4.4. VLAN Application ............................................................24

Port-based VLAN Workgroup....................................................... 24

Shared Server..............................................................................25

5. Product Specifications................................................. 27

SMC-EZ1026DT V.2

3

Figure 1-1. The
SMC-EZ1026DT V.2

1. Introduction

Welcome to the World of Switching-Network.
In modern society, communication and information sharing are
fundamental to our lifestyle. Computer networks are one of the
fastest mean of communication.
As your company grows, your network demands will increase. …

The SMC-EZ1026DT V.2 Switch is designed to provide your network
with Ethernet, Fast Ethernet, and Gigabit Ethernet connectivity over
twisted pair and fiber optic cabling. Two expansion slots on the front
panel of the SMC-EZ1026DT V.2 Switches further add to the
flexibility of the systems.

The SMC-EZ1026DT V.2 is a Smart Fast Ethernet switch, that
provides a number of exceptional features with extremely flexible
configuration expansions without compromising the wire speed

performance.
The SMC-EZ1026DT V.2 switch provide wire-speed switching with
advanced bridging functions like VLAN, link aggregation (Trunk) and
port mirroring. It can also support two different GBIC type as Mini
GBIC LC and standard GBIC SC.

SMC-EZ1026DT V.2

4

1.1 Features

▓ Conforms to IEEE802.3,IEEE 802.3 ab,

IEEE802.3u,IEEE802.3z ,IEEE802.3x IEEE802.1p

 24 auto-sensing 10/100Mbps Ethernet RJ-45 ports
 2 Expansion slots for optional modules: 1-port Gigabit

( SX/LX ), 1-port Gigabit Copper, and 1-port 100M Fiber
Module

 Automatic MDI/MDIX crossover for each 10/100Base-TX port
 One Console-connecting port for communication parameter

configuration

 Auto-negotiation & Full-duplex/half-duplex supported
 Store-and- Forward error free packet forwarding scheme
 8K-entry MAC address table
 6Mbits share memory
 Full wire speed forwarding rate
 LED-indicators for Power, 10/100M, LK/ACT, FD/ COL

statuses

Intelligent Management Features

 Console Configuration
 Port Based VLAN supported
 IEEE802.3x Flow Control Mechanism is used in Full-Duplex

mode and back-pressure is used in half-duplex

 Link Aggregation function supported
 Port Mirror supported
 Bandwidth Control

SMC-EZ1026DT V.2

5

1.2 Package Contents

Unpack the carton of the SMC-EZ1026DT V.2 Switch and verify
them against the checklist below.

SMC-EZ1026DT V.2 Switch Rubber Feet

Rack-mounted Kit RS-232 cable

Power Cord

Figure 1-2. Package Contents

Compare the contents of your SMC-EZ1026DT V.2 Switch package
with the standard checklist above. If any item is missing or damaged,
please contact your local dealer for service.

SMC-EZ1026DT V.2

6

2. Hardware Description

This section mainly describes the hardware of the SMC-EZ1026DT
V.2, and gives a functional overview of the Switch.

The physical dimensions of the SMC-EZ1026DT V.2 is: 440mmx
225mmx 44.5mm ( L x W x H )

2.1 Hardware Description

The SMC-EZ1026DT V.2 Switch has fixed 24-port auto-sensing
Ethernet RJ-45 connectors, and its chassis contains two expansion
slots.

The Front Panel

The Front Panel of the SMC-EZ1026DT V.2 consists of 24x
auto-sensing 10/100Mbps Ethernet RJ-45 Ports, two optional
expansion slots, and Console port. The LED Indicators are also
located on the front panel of the Switch.

Figure 2-1. The Front Panel of SMC-EZ1026DT V.2 Switch

LED Indicators

RJ-45 Ports

Console Port

Expansion Slots for Optional Module

SMC-EZ1026DT V.2

7

10/100Base-TX RJ-45 ports (Auto MDI / MDIX):

24x 10/100Mbps auto-sensing port for 10Base-T or 100Base-TX
devices connection. Note: [MDI/MDIX means that you can connect
to another Switch or workstation without changing non-crossover or
crossover cable.]

Expansion Slots:

For two of the following Optional modules:
1 Port Gigabit 1000Base-T Intelligent Switch Modules,
1 Port Gigabit 1000Base-SX/LX Intelligent Fiber Modules.
1 Port 100Base-FX Intelligent Fiber Module
GBIC/Mini GBIC Module

Console Port:

Console Management can be done through the Console Port. It
requires a direct connection between the SMC-EZ1026DT V.2
Switch and an end station (PC) via a RS-232 cable.

2.2 LED Indicators

All LED indicators are located on the front panel of the
SMC-EZ1026DT V.2 Switch. They provide a real-time indication of
system and operational status. The following table
gives descriptions of the LED status and their meanings.

Figure 2-2 The LED
Indicators

SMC-EZ1026DT V.2

8

LED Status

Description

Green Power On

PWR

Off Power is Off.

Green The port is operating at the speed of 100Mbps.

100

Off No device attached or in 10Mbps mode

Green The port is connecting with the device.

Blinks The port is receiving or transmitting data.

LK/ACT

Off No device attached.

Yellow The port is operating in Full-duplex mode.

Blinks Collision of Packets occurs in the port.

FD/COL

Off No device attached or in half-duplex mode .

Table 2-3. The Descriptions of LED Indicators

Rear Panel

The 3-pronged power plug, On/Off switch are located at the Rear
Panel of the SMC-EZ1026DT V.2 Switch. (The Ventilation fan is
located on the side of the switch). The Switch will work with AC in
the range 100-240V AC, 50-60Hz.

Figure 2-4. The Rear Panel of the SMC-EZ1026DT V.2 Switch

SMC-EZ1026DT V.2

9

Power On

After all network cables are connected, plug the power cord into the
power socket on the back panel and the other end into a power
outlet. Turn the power On using the power switch on the back panel.

Check the front panel Power indicator to see if power is properly
supplied. The Switch uses a universal power supply that requires no
additional adjustment.

3. Connecting to the Network

This section provides the installation procedure and instructions for
assigning IP address.

3.1 Pre-Installation Requirements

Before you start hardware installation, make sure your installation
environment has below items:

 PCs with 10/100Mbps Ethernet NICs/100/1000Mbps Fiber
NICs:

Your PC must have a standard Ethernet interface to connect to
the Switch.

 UTP cable with RJ45 connectors/ Fiber cable with MT-RJ/

VF-45 connectors: Check if the cable and connectors work

properly.

 A power outlet: 100 to 240V AC at 50 to 60 Hz: Make sure that

the Switch power is accessible and cables can be connected
easily.

 Dedicated power supply: Use a dedicated power circuits or

power conditioners to supply reliable electrical power to the
network devices.

 A dry cool place: Keep the Switch away from moisture. Avoid