SMC Networks EX260-SPR1/3, EX260-SPR2/4, EX260-SPR5/7, EX260-SPR6/8, EX260-SDN1/3 Quick Start Manual

...

RoHS

IP67IP67 IP67 IP40

Top ported valve Bottom ported valve

Side ported valve

Mixed valve sizes manifold

7 mm width valve

Applicable Fieldbus protocols

EX260 Series

Fieldbus System

(Output device for driving 5 port solenoid valves)

Daisy-chain wiring communication

Space-saving InstallationSpace-saving Installation

Compact



IP67

∗

For units with D-sub connector, and when connect ed to S0700 manifolds, it is IP40 .



Drives up to 32 solenoids

789

EX12

EX140

EX180

EX260

EX250

EX600

EX500

EX510

PCA EX

EX260

PWR

BUS IN

BUS OUT

3/5

B4A2 B4A2 B4A2 B4A2 B4A2

PWR

BUS IN

BUS OUT

3/5

B4A2 B4A2 B4A2 B4A2 B4A2

Product Specification Variations

M12 communication connector

(PROFIBUS DP)

D-sub communication connector

(PROFIBUS DP)

28.2 mm

81 mm

Communication connector examples

Fieldbus

EX260

Manifold length is shortened by the small fieldbus output module (SI unit).

Wiring and piping from the same direction is possible.

(for side ported)

Effective for installation in locations where space is limited above the valve.

Current model EX250

External branch connector is not necessary. Daisy-chain wiring is possible. Reduced wiring space

Branch connector

Current model (EX250)

External terminating resistor is not necessary.

(Only available for M12 PROFIBUS DP, CC-Link communication connectors)

ON/OFF switching is possible with an internal terminating resistor. External terminating resistor is not necessary.

External terminating resistor

Internal terminating resistor

SI unit

PNP

NPN

M12

D-sub

PNP

NPN

M12

PNP

NPN

M12

PNP

NPN

M12

PNP

NPN

M12

Number of

outputs

Output

polarity

Communication

connector

PNP

NPN

M12

PNP

M12

790

SY3000

SY5000

SY7000

S0700

SV1000

SV2000

SV3000

VQC1000

VQC2000

VQC4000

VQC5000

0.19

0.17

0.20

0.39

0.35

0.18

0.21

0.30

0.38

0.31

1.6

3.6

5.9

0.37

1.1

2.4

4.3

1.0

3.2

7.3

Series

Power

consumption

(W)

Enclosure Standards

Flow rate characteristics (4/2→5/3)

C [dm

/(s·bar)] b

Maximum number of solenoids



Applicable Valve Series

Note) For units with D-sub communication connector, it is IP40.

0.35 (standard)

0.1 (with powersaving circuit) [Starting 0.4,

Holding 0.1]

0.6

0.95 (standard)

0.4 (Low wattage type)

0.4 (standard)

0.35

IP67

IP40

IP67

Side ported

Bottom ported

Top ported

Valve piping direction variations

SY3000/5000/7000 Series

Pressure switch

Piping is possible from 3 directions.

Mixed mounting of top ported and side ported is possible.

By mounting top ported valves on side ported and bottom ported type manifolds, it is possible to detect the output of the A/B port with a pressure switch.

Valves can be freely connected up to 24 stations.

Mixed valve sizes manifold

Valves with different sizes,

SY3000 and SY5000 or SY5000 and SY7000, can be mounted on the same manifold.



It is possible to connect only the number of valves required, from 1 to 24 stations, to suit the application. (Maximum number of solenoids connected: 32)

7 mm width valves

can be connected.



It is possible to connect only the number of 7 mm width valves required, from 1 to 24 stations. (Maximum number of solenoids connected: 32)

S0700 Series

791

EX12

EX140

EX180

EX260

EX250

EX600

EX500

EX510

PCA EX

EX260

M12

DN1 DN2 DN3 DN4 PR1 PR2 PR3 PR4 PR5 PR6 PR7 PR8 MJ1 MJ2 MJ3 MJ4 EC1 EC2 EC3 EC4 PN1 PN2 PN3 PN4 EN1 EN2 EN3 EN4 PL1 PL3

DeviceNet™

PROFIBUS DP

EtherCAT

PROFINET

POWERLINK

SI unit output polarity

32 16

M12

D-sub

Note)

M12

EtherNet/IP™

M12

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

Sink/NPN (Positive common)

Source/PNP (Negative common)

QAN

QBN

NAN

NBN

NCN

NDN

VAN

VBN

DAN

DBN

FAN

FBN

EAN

EBN

EB GAN GBN

Communication protocol

Compact design

Compact design for space saving

Number of outputs

Each 32/16 digital output type available in the series

Enclosure

IP67 (For units with D-sub connector, and when connected with S0700 manifolds, it is IP40.)

Output polarity

Each negative common (PNP) / positive common (NPN) type available in the series (SI Unit compatible with POWERLINK is only negative common (PNP) type.)

Internal terminating resistor

ON/OFF switching is possible with an internal terminating resistor for communication. (Only for units compatible with M12 PROFIBUS DP, CC-Link communication connectors)

SY3000/5000/7000 VQC1000/2000/4000/5000 S0700 SV1000/2000/3000

How to Order SI Units

PR1

EX260 S

Note)

Note) The SY3000/5000/7000, VQC1000/2000/4000/5000, and S0700 are not yet UL-compatible.

CC-Link

RoHS

Protocol

Symbol

Number of outputs

Communication connector

Manifold symbol

EX260 Series

SI Unit/For Output

Note) Enclosure is IP40 when the communication connector is D-sub.

792

SI Unit Specifications

Model

EX260-SPR1/3 EX260-SPR2/4 EX260-SPR5/7 EX260-SPR6/8 EX260-SDN1/3 EX260-SDN2/4 EX260-SMJ1/3 EX260-SMJ2/4

125 k/250 k/500 kbps

156 k/625 k/

2.5 M/5 M/10 Mbps

M12

Built-in

—

22.8 to 26.4 VDC 11 to 25 VDC

100 mA or less

Applicable system

I/O occupation area (Inputs/Outputs)

Communication speed

Power supply for control Power supply for output

Communication connector specification Terminating resistor switch

Power supply for communication

Output

Environmental resistance

Standards Weight

Mounting screw

Accessories

IP67 IP40 IP67

–10 to 50°C

35 to 85%RH (No condensation)

500 VAC for 1 minute between terminals and housing

10 MΩ or more (500 VDC measured via megohmmeter) between terminals and housing

CE marking, UL (CSA) compatible

200 g 2 pcs.

24 VDC

Power supply voltage

Internal current consumption

Power supply voltage Power supply voltage

Internal current consumption

Protocol

Version

Note 1)

Configuration file

Note 3)

Supplied current

Output type

Number of outputs

Load Supplied voltage

Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation resistance

Seal cap (for M12 connector socket)

Source/PNP

(Negative common)

Sink/NPN

(Positive common)

Source/PNP

(Negative common)

Sink/NPN

(Positive common)

Source/PNP

(Negative common)

Sink/NPN

(Positive common)

SPR1: 32 points SPR3: 16 points

SPR2: 32 points SPR4: 16 points

SPR5: 32 points SPR7: 16 points

SPR6: 32 points SPR8: 16 points

SDN1: 32 points SDN3: 16 points

SDN2: 32 points SDN4: 16 points

SPR1: 0/32 SPR3: 0/16

SPR2: 0/32 SPR4: 0/16

SPR5: 0/32 SPR7: 0/16

SPR6: 0/32 SPR8: 0/16

SDN1: 0/32 SDN3: 0/16

SDN2: 0/32 SDN4: 0/16

SMJ1: 32/32 SMJ3:

32/32

(1 station, remote I/O stations)

SMJ2: 32/32 SMJ4:

32/32

(1 station, remote I/O stations)

SPR1: Max. 2.0 A SPR3: Max. 1.0 A

SPR2: Max. 2.0 A SPR4: Max. 1.0 A

SPR5: Max. 2.0 A SPR7: Max. 1.0 A

SPR6: Max. 2.0 A SPR8: Max. 1.0 A

SDN1: Max. 2.0 A SDN3: Max. 1.0 A

SDN2: Max. 2.0 A SDN4: Max. 1.0 A

EX9-AWTS (1 pc.) — EX9-AWTS (1 pc.)

D-sub M12

None Built-in

Volume 1(Edition 3.5) Volume 3(Edition 1.5)

9.6 k/19.2 k/45.45 k/93.75 k/

187.5 k/500 k/1.5 M/3 M/6 M/12 Mbps

21.6 to 26.4 VDC 100 mA or less

— —

—

21.6 to 26.4 VDC 100 mA or less

PROFIBUS DP

DeviceNet™

CC-Link

DP-V0 Ver.1.10

—

GSD file EDS file

Source/PNP

(Negative common)

Sink/NPN

(Positive common)

SMJ1: 32 points SMJ3: 16 points

SMJ2: 32 points SMJ4: 16 points

SMJ1: Max. 2.0 A SMJ3: Max. 1.0 A

SMJ2: Max. 2.0 A SMJ4: Max. 1.0 A

Solenoid valve with protective circuit for surge voltage of 24 VDC/1.5 W or less (SMC)

Model

EX260-SEC1/3 EX260-SEC2/4 EX260-SPN1/3 EX260-SPN2/4 EX260-SEN1/3 EX260-SEN2/4

Applicable system

I/O occupation area (Inputs/Outputs)

Communication speed Power supply for control Power supply for output

Communication connector specification Terminating resistor switch

Power supply for communication

Output

Environmental resistance

Standards Weight

Mounting screw

Accessories

IP67

–10 to 50°C

35 to 85%RH (No condensation)

500 VAC for 1 minute between terminals and housing

CE marking, UL (CSA) compatible

200 g 2 pcs.

10 MΩ or more (500 VDC measured via megohmmeter) between terminals and housing

24 VDC

Power supply voltage

Internal current consumption

Power supply voltage Power supply voltage

Internal current consumption

Protocol

Version

Note 1)

Configuration file

Note 3)

Supplied voltage

Output type

Number of outputs

Load

Supplied voltage

Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation

resistance

Seal cap (for M12 connector socket)

Source/PNP

(Negative common)

Sink/NPN

(Positive common)

Source/PNP

(Negative common)

Sink/NPN

(Positive common)

Source/PNP

(Negative common)

Sink/NPN

(Positive common)

SEC1: 32 points SEC3: 16 points

SEC2: 32 points SEC4: 16 points

SPN1: 32 points SPN3: 16 points

SPN2: 32 points SPN4: 16 points

SEN1: 32 points SEN3: 16 points

SEN2: 32 points SEN4: 16 points

SEC1: 0/32 SEC3: 0/16

SEC2: 0/32 SEC4: 0/16

SPN1: 0/32 SPN3: 0/16

SPN2: 0/32 SPN4: 0/16

SEN1: 16/32 SEN3: 16/16

SEN2: 16/32 SEN4: 16/16

SEC1: Max. 2.0 A SEC3: Max. 1.0 A

SEC2: Max. 2.0 A SEC4: Max. 1.0 A

SPN1: Max. 2.0 A SPN3: Max. 1.0 A

SPN2: Max. 2.0 A SPN4: Max. 1.0 A

SEN1: Max. 2.0 A SEN3: Max. 1.0 A

SEN2: Max. 2.0 A SEN4: Max. 1.0 A

EX9-AWTS (1 pc.)

Volume 1(Edition 3.8) Volume 2(Edition 1.9)

21.6 to 26.4 VDC 100 mA or less

22.8 to 26.4 VDC

— —

M12

None (Not required)

10 M/100 Mbps

Note 2)

100 Mbps

Note 2)

EtherCAT

Note 2)

EtherNet/IP™

Note 2)

Conformance

Test Record V.1.1

XML file

PROFINET

Note 2)

PROFINET Specification

Version 2.2

GSD file EDS file

Solenoid valve with protective circuit for surge

voltage of 24 VDC/1.5 W or less (SMC)

Solenoid valve with protective circuit for surge

voltage of 24 VDC/1.0 W or less (SMC)

Solenoid valve with protective circuit for surge

voltage of 24 VDC/1.5 W or less (SMC)

EX260-SPL1 EX260-SPL3

Source/PNP

(Negative common)

32 16

16/32 16/16

Max. 2 A Max. 1 A

EPSG DS 301 Version 1.2.0

100 Mbps

Note 2)

POWERLINK

XDD file

Note 1) Please note that the version is subject to change. Note 2) Use a CAT5 or higher transmission cable for EtherCAT, PROFINET, EtherNet/IP™, POWERLINK. Note 3) Each file can be downloaded from the SMC website, http://www.smcworld.com

For Output EX260 Series

793

EX12

EX140

EX180

EX260

EX250

EX600

EX500

EX510

PCA EX

EX260

+ 10 hidden pages

SMC Networks EX260-SPR1/3, EX260-SPR2/4, EX260-SPR5/7, EX260-SPR6/8, EX260-SDN1/3 Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

How to Order SI Units