SMC Networks AR9381DB24 User Manual

DOCSIS 3.0 Wireless Gateway Installation Instructions

Important Safety Instructions

Read these instructions before you begin

When using your equipment, basic safety precautions should always be followed to reduce the risk of re,

electric shock, and injury to persons, including the following:

• Read and follow these instructions.

• Keep these instructions.

• Heed all warnings.

• Only use attachments/accessories specied by the manufacturer.

• Do not install near any heat sources.

• Clean only with a dry cloth.

• Do not block any ventilation openings.

• Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the

apparatus.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been

damaged in any way, such as when a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

• Do not alter or disable the polarized or grounding-type (three-pronged) plug.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

SMC Wireless Gateway complies with applicable requirements for performance, construction, labeling, and

information when used in accordance with the instructions below:

WARNING: Risk of Shock

Mains voltages inside this unit. No user serviceable parts inside. Refer service to qualied personnel

only! Avoid using and/or connecting the equipment during an electrical storm, to avoid risk of electrocution.

AVERTISSEMENT: Risque d’électrocution

Tensions du secteur dans cette unité. Ne contient aucune pièce pouvant être réparée par l’utilisateur. Tout entretien doit être effectué par du personnel qualié seulement!

• Do not use this product near water (i.e. wet basement, bathtub, sink or near a swimming pool, etc.) to

avoid risk of electrocution.

• Avoid using and/or connecting the equipment during an electrical storm, to avoid risk of electrocution.

• Do not locate the equipment within 6 feet (1.9m) of a ame or ignition source (i.e. heat registers, space heaters, replaces, etc.).

• Only use power supply and power cord included with the equipment.

• Equipment should be installed near the power outlet and should be easily accessible.

• The shield of the coaxial cable must be connected to earth (Grounded) at the entrance to the building in accordance with applicable national electrical installation codes. In the U.S., this is required by NFPA 70 (National Electrical Code) Article 820. In the European Union and in certain other countries, CATV installation equipment bonding requirements are specied in IEC 60728-11, Cable networks for television signals, sound signals and interactive service, Part 11: Safety. This equipment is intended to be installed in accordance with the requirements of IEC 60728-11 for safe operation.

• In areas of high surge events or poor grounding situations and areas prone to lightning strikes, additional

surge protection may be required on the AC, and Ethernet cables.

Rev 1.1 Nov 2013

DOCSIS 3.0 Wireless Gateway Installation Instructions

Models

The SMC Wireless Gateway comes in one version: D3G2408WE.

Package Contents

• 1 – Wireless Data Gateway

• 1 – Power Supply and AC Power Cord

• 1 – CAT-5 Ethernet cable

• 1 – These Installation Instructions

Installation Overview

1. Connect the coaxial cable from the cable outlet to the Gateway.

2. Connect your wired connections (Ethernet and USB) to the rear panel as shown in the diagram below.

3. Connect the power supply to the Gateway and to a wall power outlet.

WARNING: Use only the provided power supply! Using a different power supply may damage your unit

and void the warranty.

AVERTISSEMENT: Utilisez uniquement la source d’alimentation fournie! L’utilisation d’une autre source

d’alimentation risque d’endommager l’unité et d’annuler la garantie.

4. Conrm the front panel POWER LED is ON.

5. Wait until the DS, US and ONLINE LED stop ashing and the ONLINE LED stays ON indicating that the device is online. If the ONLINE LED does not go ON in 5 minutes, contact your Internet Service Provider.

6. If your computer or wireless client device supports WPS (Wi-Fi Protected Setup), press the WPS button

on the front panel for 5 seconds to enable WPS.

7. Press the WPS button on your computer or wireless client within 60 seconds to complete association process. When a client joins the network, the WPS LED stays ON until the next WPS action or the device

reboots. If no client joins, the LED stops blinking after 4 minutes.

NOTE: You must set up your computer and other wireless client devices to work with security settings on this device. Refer to the documentation for your wireless client devices for instructions on setting security.

8. (Optional): Log in to congure additional device settings.

• Open a Web browser page and type http://192.168.0.1 in the address bar.

• At the Login screen, enter the following login information:

(NOTE: Username and password are case sensitive.)

Username: admin Password: password

Detailed user manual can be downloaded from http://na.smc.com.

All information contained in this documentation is subject to change without notice.

+ 2 hidden pages