Smc SMCGS10P-SMART installation guide

INSTALLATION GUIDE

EZ SwitchTM 10/100/1000 Web Smart 10-Port Gigabit Ethernet PoE Switch

SMCGS10P-Smart

EZ Switch

10/100/1000

Installation Guide

From SMC’s EZ line of low-cost workgroup LAN solutions

No. 1, Creation Road III, Hsinchu Science Park, 30077, Taiwan, R.O.C. TEL: +886 3 5770270 Fax: +886 3 5780764

December 2011

150200000312A

SMC-IG-1211-01

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice.

SMC Networks

No. 1, Creation Road III,

Hsinchu Science Park,

30077, Taiwan, R.O.C.

Trademarks:

SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are trademarks of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders.

ARRANTY AND PRODUCT REGISTRATION

To register SMC products and to review the detailed warranty statement, please refer to the Support Section of the SMC Website at http://www.smc.com.

– 4 –

COMPLIANCES AND SAFETY STATEMENTS

FCC - CLASS A

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

◆ This device may not cause harmful interference.

◆ This device must accept any interference received, including interference

that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

– 5 –

OMPLIANCES AND SAFETY STATEMENTS

CE MARK DECLARATION OF CONFORMANCE FOR EMI AND SAFETY (EEC)

This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/ 68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:

RFI Emission:

Immunity:

LVD:

◆ Limit according to EN 55022:2007, Class A/B

◆ Limit for harmonic current emission according to EN 61000-3-2:2006,

Class A

◆ Limitation of voltage fluctuation and flicker in low-voltage supply

system according to EN 61000-3-3:2005

◆ Product family standard according to EN 55024:2001 + A2:2003

◆ Electrostatic Discharge according to IEC 61000-4-2:2008

◆ Radio-frequency electromagnetic field according to IEC 61000-4-

3:2007

◆ Electrical fast transient/burst according to IEC 61000-4-4:2004

◆ Surge immunity test according to IEC 61000-4-5:2005

◆ Immunity to conducted disturbances, Induced by radio-frequency

fields: IEC 61000-4-6:2008

◆ Power frequency magnetic field immunity test according to IEC

61000-4-8:2001

◆ Voltage dips, short interruptions and voltage variations immunity test

according to IEC 61000-4-11:2004

◆ EN60950-1:2006+A11:2009

– 6 –

CLASS I

LASER DEVICE

DISPOSITIF LASER

DE CLASSE I

LASERGER DER KLASSE I

ÄT

OMPLIANCES AND SAFETY STATEMENTS

SAFETY COMPLIANCE

Warning: Fiber Optic Port Safety

When using a fiber optic port, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable ends when they are powered on.

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique

Ne regardez jamais le laser tant qu'il est sous tension. Ne regardez jamais directement le port TX (Transmission) à fibres optiques et les embouts de câbles à fibres optiques tant qu'ils sont sous tension.

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

Niemals ein Übertragungslaser betrachten, während dieses eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß und auf die Faserkabelenden schauen, während diese eingeschaltet sind.

PSE ALARM

本製品に同梱いたしております電源コードセットは、本製品専用です。本電源コードセットは、本製品以外の製品並びに他の用途でご使用いただくことは出来ません。製品本体に同梱された電源コードセットを利用し、他製品の電源コードセットを使用しないで下さい。

– 7 –

OMPLIANCES AND SAFETY STATEMENTS

POWER CORD SAFETY

Please read the following safety information carefully before installing the switch:

WARNING:

Installation and removal of the unit must be carried out by qualified

personnel only.

◆ The unit must be connected to an earthed (grounded) outlet to comply with

international safety standards.

◆ Do not connect the unit to an A.C. outlet (power supply) without an earth

(ground) connection.

◆ The appliance coupler (the connector to the unit and not the wall plug) must

have a configuration for mating with an EN 60320/IEC 320 appliance inlet.

◆ The socket outlet must be near to the unit and easily accessible. You can

only remove power from the unit by disconnecting the power cord from the outlet.

◆ This unit operates under SELV (Safety Extra Low Voltage) conditions

according to IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT

†

supplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection point labelled Neutral, connected directly to earth (ground).

†

Impédance à la terre

MPORTANT

Before making connections, make sure you have the correct cord

set. Check it (read the label on the cable) against the following:

– 8 –

OMPLIANCES AND SAFETY STATEMENTS

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least 10 A

The attachment plug must be an earth-grounding type with NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

Denmark The supply plug must comply with Section 107-2-D1, Standard

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be fitted

Europe The supply plug must comply with CEE7/7 (“SCHUKO”).

DK2-1a or DK2-5a.

with a 5 A fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and be of type HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch:

AVERTISSEMENT:

L’installation et la dépose de ce groupe doivent être confiés à

un personnel qualifié.

◆ Ne branchez pas votre appareil sur une prise secteur (alimentation

électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la masse).

◆ Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la

masse) afin de respecter les normes internationales de sécurité.

◆ Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale)

doit respecter une configuration qui permet un branchement sur une entrée d’appareil EN 60320/IEC 320.

– 9 –

OMPLIANCES AND SAFETY STATEMENTS

◆ La prise secteur doit se trouver à proximité de l’appareil et son accès doit

être facile. Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique au niveau de cette prise.

◆ L’appareil fonctionne à une tension extrêmement basse de sécurité qui est

conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il est raccordé fonctionne dans les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec raccordement direct à la terre (masse).

Cordon électrique - Il doit être agréé dans le pays d’utilisation

Etats-Unis et Canada: Le cordon doit avoir reçu l’homologation des UL et un certificat de

Danemark: La prise mâle d’alimentation doit respecter la section 107-2 D1 de

Suisse: La prise mâle d’alimentation doit respecter la norme SEV/ASE

Europe La prise secteur doit être conforme aux normes CEE 7/7

la CSA.

Les spécifications minimales pour un cable flexible sont AWG No. 18, ouAWG No. 16 pour un cable de longueur inférieure

ètres.

- type SV ou SJ

- 3 conducteurs

Le cordon doit être en mesure d’acheminer un courant nominal d’au moins 10 A.

La prise femelle de branchement doit être du type à mise à la terre (mise à la masse) et respecter la configuration NEMA 5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V).

la norme DK2 1a ou DK2 5a.

1011.

(“SCHUKO”) LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit être de type HO3VVF3GO.75 (minimum).

à 2

– 10 –

OMPLIANCES AND SAFETY STATEMENTS

Bitte unbedingt vor dem Einbauen des Switches die folgenden Sicherheitsanweisungen durchlesen:

WARNUNG:

Die Installation und der Ausbau des Geräts darf nur durch

Fachpersonal erfolgen.

◆ Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose

angeschlossen werden.

◆ Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche

die internationalen Sicherheitsnormen erfüllt.

◆ Der Gerätestecker (der Anschluß an das Gerät, nicht der

Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320 konfigurierten Geräteeingang haben.

◆ Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein.

Die Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.

◆ Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen

(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen betrieben werden.

Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:

Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalten.

Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung)

sein und die Aufschrift <HAR> oder <BASEC> tragen. Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).

– 11 –

OMPLIANCES AND SAFETY STATEMENTS

WARNINGS AND CAUTIONARY MESSAGES

ARNING

This product does not contain any serviceable user parts.

ARNING

Installation and removal of the unit must be carried out by

qualified personnel only.

ARNING

field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards.

ARNING

cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

AUTION

measures to prevent electrostatic discharge when handling this equipment.

AUTION

may damage this device.

AUTION

conform to FCC standards.

When connecting this device to a power outlet, connect the

This switch uses lasers to transmit signals over fiber optic

Wear an anti-static wrist strap or take other suitable

Do not plug a phone jack connector in the RJ-45 port. This

Use only twisted-pair cables with RJ-45 connectors that

ENVIRONMENTAL STATEMENTS

The manufacturer of this product endeavours to sustain an environmentallyfriendly policy throughout the entire production process. This is achieved though the following means:

◆ Adherence to national legislation and regulations on environmental

production standards.

◆ Conservation of operational resources.

◆ Waste reduction and safe disposal of all harmful un-recyclable by-products.

◆ Recycling of all reusable waste content.

◆ Design of products to maximize recyclables at the end of the product’s life

span.

◆ Continual monitoring of safety standards.

– 12 –

OMPLIANCES AND SAFETY STATEMENTS

END OF PRODUCT LIFE SPAN

This product is manufactured in such a way as to allow for the recovery and disposal of all included electrical components once the product has reached the end of its life.

MANUFACTURING MATERIALS

There are no hazardous nor ozone-depleting materials in this product.

DOCUMENTATION

All printed documentation for this product uses biodegradable paper that originates from sustained and managed forests. The inks used in the printing process are non-toxic.

– 13 –

OMPLIANCES AND SAFETY STATEMENTS

– 14 –

ABOUT THIS GUIDE

PURPOSE

This guide details the hardware features of the switch, including the physical and performance-related characteristics, and how to install the switch.

AUDIENCE

The guide is intended for use by network administrators who are responsible for installing and setting up network equipment; consequently, it assumes a basic working knowledge of LANs (Local Area Networks).

CONVENTIONS

The following conventions are used throughout this guide to show information:

OTE

Emphasizes important information or calls your attention to

related features or instructions.

AUTION

Alerts you to a potential hazard that could cause loss of data,

or damage the system or equipment.

ARNING

Alerts you to a potential hazard that could cause personal

injury.

REVISION HISTORY

This section summarizes the changes in each revision of this guide.

DECEMBER 2011 REVISION

This is the first revision of this guide.

– 15 –

BOUT THIS GUIDE

– 16 –

CONTENTS

WARRANTY AND PRODUCT REGISTRATION 4

OMPLIANCES AND SAFETY STATEMENTS 5

BOUT THIS GUIDE 15

ONTENTS 17

ABLES 19

IGURES 21

NTRODUCTION 22

Overview 22

Switch Architecture 23 Network Management Options 23 Power-over-Ethernet 23 Description of Hardware 24

2NETWORK PLANNING 30

Introduction to Switching 30 Application Examples 30

Collapsed Backbone 30 PoE Connections 31 Network Aggregation Plan 32

Application Notes 34

3INSTALLING THE SWITCH 36

Selecting a Site 36 Ethernet Cabling 37 Equipment Checklist 38

– 17 –

ONTENTS

Optional Rack-Mounting Equipment 38 Mounting 39

Rack-Mounting 39 Connecting to a Power Source 42 Installing an Optional SFP Transceiver 43

4MAKING NETWORK CONNECTIONS 44

Connecting Network Devices 44 Twisted-Pair Devices 44

Power-over-Ethernet Connections 44 Cabling Guidelines 45 Connecting to PCs, Servers, Hubs and Switches 45

Network Wiring Connections 46 Fiber Optic SFP Devices 47 Connectivity Rules 49

1000BASE-T Cable Requirements 49

1000 Mbps Gigabit Ethernet Collision Domain 49

100 Mbps Fast Ethernet Collision Domain 50

10 Mbps Ethernet Collision Domain 51 Cable Labeling and Connection Records 51

ATROUBLESHOOTING 52

Diagnosing LED Indicators 52 Power and Cooling Problems 52 Installation 53 In-Band Access 53

BSPECIFICATIONS 54

Physical Characteristics 54 Switch Features 56 Management Features 56 Standards 56 Compliances 57

– 18 –

+ 41 hidden pages