Smc GS8, GS5 User Manual

EZ Switch™

EZ Connect N

5/8 port Gigabit Ethernet Switch

Draft 11n Wireless USB2.0 Adapter

SMCGS5/SMCGS8

Copyright

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of
patents or other rights of third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to
change specifications at any time without notice.

Copyright © 2009 by

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

All rights reserved. Printed in Taiwan

Trademarks:

SMC is a registered trademark; and EZ Switch is a trademark of SMC Networks, Inc. Other
product and company names are trademarks or registered trademarks of their respective
holders.

1

Warranty and

Product Registration

To register SMC products and to review the detailed warranty statement, please refer to the
Support Section of the SMC Website at http://www.smc.com

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

2

Compliances

Federal Communication Commission Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct
the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC
emission limits. SMC is not responsible for any radio or television interference caused by
using other than recommended cables and connectors or by unauthorized changes or
modifications to this equipment. Unauthorized changes or modifications could void the
user's authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.

EC Declaration of Conformity

SMC contact for these products in Europe is:

SMC Networks Spain, S.L.
Edificio Conata II,
Group CTSG
Fructuos Gelabert 6-8 2o2a
08970 Sant Joan Despi, Barcolona,Spain

This information technology equipment complies with the requirements of the Council
Directive 2004/108/EC on the Approximation of the laws of the Member States relating to
Electromagnetic Compatibility and 2006/95/EC for electrical equipment used within certain
voltage limits and the Amendment Directive 2006/95/EC. For the evaluation of the
compliance with these Directives, the following standards were applied:

RFI Emission:

• Limit class A according to EN 55022: 2006(EMC)

• Limit class A for harmonic current emission according toEN 61000-3-

2/2000+A2:2005

• Limitation of voltage fluctuation and flicker in low-voltage supply system according

to EN 61000-3-3/1995+A1:2001+A2:2005

Immunity:

• Product family standard according to EN 55024:1998+A1:2001+A2:2003

3

• Electrostatic Discharge according to EN 61000-4-2: 2001 ED.1.2

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to EN 61000-4-3: 2006 ED.3.0

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4: 2004 ED.2.0 (AC/DC

power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5: 2005 ED.2.0

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by radio-frequency fields:

EN 61000-4-6: 2006 ED.2.2 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3
V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:

2001 ED.1.1 (1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test according to

EN 61000-4-11: 2004 ED.2.0 (>95% Reduction @10 ms, 30% Reduction @500 ms,
>95% Reduction @5000 ms)

LVD:

• EN 60950-1:2006

Industry Canada Statement

This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled .Digital
Apparatus,. ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe A prescrites dans la norme sur le matériel
brouilleur: .Appareils Numériques,. NMB-003 édictée par le ministère des Communications.

4

Please read the following safety information carefully before
installing the Switch:

WARNING: Installation and removal of the unit must be carried out by qualified personnel

only.

• This guide is intended for use by network administrators who are responsible for

setting up and installing network equipment; consequently it assumes a basic
working knowledge of LANs (Local Area Networks).

• The unit must be connected to an earthed (grounded) outlet to comply with

international safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without an earth (ground)

connection.

• The appliance coupler (the connector to the unit and not the wall plug) must have a

configuration for mating with an EN 60320/IEC 320 appliance inlet.

• The socket outlet must be near to the unit and easily accessible. You can only

remove power from the unit by disconnecting the power cord from the outlet.

• This unit operates under SELV (Safety Extra Low Voltage) conditions according to

IEC 60950. The conditions are only maintained if the equipment to which it is
connected also operates under SELV conditions.

5

France and Peru only

This unit cannot be powered from IT. supplies. If your supplies are of IT type, this unit
must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary
connection point labelled Neutral, connected directly to earth (ground). †Impédance à la
terre

Power Cord Set

U.S.A. and Canada

Denmark

Switzerland The supply plug must comply with SEV/ASE 1011.
U.K.

Europe

The cord set must be UL-approved and CSA certified.
The minimum specifications for the flexible cord are: - No.

18 AWG - not longer than 2 meters, or 16 AWG. - Type
SV or SJ - 3-conductor
The cord set must have a rated current capacity of at least
10A.

The attachment plug must be an earth-grounding type with
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V)
configuration.
The supply plug must comply with Section 107-2-D1,
Standard DK2-1a or DK2-5a.

The supply plug must comply with BS1363 (3-pin 13 A) and
be fit-ted with a 5 A fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked
and be of type HO3VVF3GO.75 (minimum).

The supply plug must comply with CEE7/7 (.SCHUKO.).
The mains cord must be <HAR> or <BASEC> marked

and be of type HO3VVF3GO.75 (minimum).
IEC-320 receptacle.

6