smartwares RM218 User manual
RM218
10.006.74
GB
DE
NL
FR
ES
PL
Users manual 4 - 140
Gebrauchsanweisung 15 - 26
Gebruikershandleiding 12 - 20
Mode d’emploi 30 - 38
Manual de usuario 39 - 47
Instrukcja obslugi 48 - 56
1
Activate - Aktivieren - Activar = 5sec.
2
3
Test - Prüfung - Prueba = 1x
Lock - Fixierstift
Fijación pin
LED
-1-
4
a
b
5
Lock - Fixierstift
Fijación pin
-2-
MINIMUM
MINIMUM
EXTRA
EXTRA
cm
0
0
1
Test - Prüfung - Prueba
ATTIC/BODEN/ZOLDER/MANSARD
GROUND/ERDGESCHOSS/BEGANEGROND/Pr.ETAGE
Entree
Test - Prüfung - Prueba
50cm
GB
SMOKE DETECTOR
IMPORTANT INFORMATION
1. General product information:
The smoke detector, if properly installed and maintained,
sounds the alarm at an early stage of the fire. This can give
you those extra valuable seconds to evacuate your home and
call the fire department. The smoke detector works on 3V
lithium direct current. Under normal conditions the service life
of the battery is up to 10 years. When the battery is (almost)
empty, the smoke detector indicates this by an audible “beep”.
This indicator sounds every 30-40 seconds during minimum 30
days. End of life, replace complete smoke detector!
2. Make/model number: Smartwares RM218
3. Power supply: 3V DC CR123A Lithium
(not replaceable battery)
25cm
4. Certification marks:
0832
RM218-001CPR
14
EN14604:2005/AC:2008
Smartwares RM218
G212177
5. Scope of application: Smoke detector for buildings with
residential function.
-3-
-4-
6. Function: Gives a warning when smoke caused by a fire is
detected.
7. Description: Smoke detector based on the photocell principle,
which means that the alarm monitors the air for smoke caused
by fire. The smoke detector does not detect heat, gas or fire.
8. Advice: Keep these instructions in a safe, easily accessible
place (e.g. electricity meter box).
9. Caution: The alarm is designed in order to detect smoke; it
cannot prevent a fire.
10.Caution: The smoke detector should not be painted. Protect
the smoke detector from dust during renovation work.
11.Caution: The smoke detector should not be taped/covered
(this causes loss of functionality).
12.Caution: Keep the smoke detector out of the reach of
children.
Press test button (1) and hold it for above 5 seconds until LED
lights, and release it within 1 second, the unit will generate a
“beep” indicates that it is activated and goes into work status.
CAUTION: Activate alarm first or else there is no function for this
unit.
Test the unit to ensure proper operation by pressing the test
button, this will sound the alarm if the electronic circuitry, horn,
and battery are working. If no alarm sounds, there is a defective
battery or other failure.
ACTIVATION
TESTING
NOTE: MONTHLY TESTING IS REQUIERED
DO NOT: Use an open flame to test your alarm, you could
damage the alarm or ignite combustible materials and start a fire.
CAUTION: Due to the loudness (85 decibels) of the alarm.
Always stand an arms-length always from the unit when testing.
Test the alarm weekly to ensure proper operation. Erratic or low
sound coming from your alarm may indicate a defective alarm.
INSTALATION
1. What is the best place to mount a smoke detector
* On the ceiling, 50cm from every edge.
* At least one on each floor.
* In every bedroom.
* In the hallway and stairwell.
* On the landing.
* In the living room.
* In the storage room or rooms with electrical appliances.
2. The alarm should not be installed in:
* A space where the temperature can drop below 4
and above 40°C
* In humid areas.
* Right next to doors or windows and not near a fan or radiator.
-5-
-6-
Do not install the alarm in a place with difficult access, which could
make it difficult to operate the test button, replace the battery and
maintenance. The alarm can be installed quickly and easily. Install
the base plate on the selected location using the provided screws.
3. Mounting
* Screw the mounting place with 2 screws on the celling
* Take the fixation pin out of the ground plate
* Activate the detector before mounting
* Fix the detector on the mounting plate by turning,
till you hear a “click”
* Put the fixation pin in the hole
* Test the smoke alarm by pushing the test button
4. Caution
* Do not cover the smoke detector with tape! When SMOKE is
detected, you will hear a loud intermittent sound (85dB).
Smoke alarms are designed to minimize nuisance alarms.
Combustion particles from cooking may set off the alarm if the alarm
is located close to the cooking area. Large quantities of combustible
particles are generated from spills or when grilling/frying. Using the
fan on a range hood that vents to outside (non-recirculating type)
will also help remove these combustible particles from the kitchen.
The alarm silence (test button) is extremely useful in a kitchen area
or other areas prone to nuisance. The hush feature is to be used only
when a known alarm condition, such as smoke from cooking
activates the alarm. The smoke alarm is desensitized by push the
alarm silence (hush mode) on the smoke alarm cover, if the smoke is
not too dense, the alarm will silence to indicate that the alarm is in a
temporarily desensitized condition. The smoke alarm will automatically reset after approximately 10 minutes, if after this period,
particles of combustion are still present, the alarm will sound again.
The alarm silencer (hush mode) can be repeatedly until the air has
been cleared of the condition causing the alarm.
5. Recommendation
* Increase the detection area by installing several smoke
detectors.
ALARM SILENCE (hush mode)
During the unit is alarming, you push the test button, it will be
paused the unit alarming for approx. 10 minutes. The red LED will
flash every 8 seconds, it indicates the smoke alarm is running into
the hush mode.
-7-
NOTE: Dense smoke will override the alarm silencer and sound a
continuous alarm, the unit goes back to normal work status from
hush mode
CAUTION: Before using the alarm silence (hush), identify the
source of the smoke and be certain a safe condition exists.
-8-
Loading...