Smart Power Systems SmartNet II User Manual

The new SmartNet II is the only
with easy installation
www.smartpowersystems.com 1-800-882-8285
PN16000650 Rev.04-12
USER'S GUIDE
USER'S GUIDE
Data Line & Signal Protection
Data Line & Signal Protection
Model C
Model A
SmartNet II
Smart Power Systems Inc. is an engineering and manufacturer of power quality products. The new SmartNet II is the only data line and signal protector with easy installation for telephone equipment/DSL (RJ11), network (RJ45), big screen tv/cable (coaxial) and CCTV/security system (BNC).
THE USE OF THE SMARTNET IN LIFE SU­PPORT APPLICATIONS WHERE FAILURE OF THE SMARTNET IS EXPECTED TO CAUSE THE FAILURE OF THE LIFE SUPPORT EQUIPMENT IS NOT RECOMMENDED.
FOR SAFETY AND OPTIMUM PERFORMANCE, THE SMARTNET SHOULD BE PROPERLY GROUNDED.
Specifications and Applications 4
MODEL
IN/OUT JACK
SN-Net5e
RJ45
SN-NPOE
RJ45
SN-Tel
RJ11
CLAMPING VOLTAGE
AND PIN CONNECTION
7.5 Volts protecting pins 1 through 8 for Network
75 Volts protecting pins 1 through 8 for POE Network
300 Volts protecting pins 4 and 5 for phone line
APPLICATION
10/100/1000Based-T Cat5e. For protection of high speed networked equipment
For protection of POE (Power Over Ethernet) network, T-1 equipment
For protection of phone systems, fax, answering machines and DSL/modems
2
Features
• Easy installation with connection to ground
• Stand-alone data line and signal protection
• Protects any electronic equipment against surges that
come through the telephone and data line.
• Noticeably increases download speed (up to 200%)
For T1, T3, 10/100/1000 Based-T, ISDN, DSL, etc.
• Handle data line with speed of over 300MHz
• All units come with the necessary patch cables, except
on the coaxial and BNC models.
• No tools necessary for installation of Model A
• Available in colors black and computer gray
Specifications and Applications
MODEL
IN/OUT JACK
SN-Tel2
RJ11
SN-TV
Coaxial
SN-BNC
BNC
CLAMPING VOLTAGE
AND PIN CONNECTION
300 Volts protecting pins 4 and 5 also 3 and 6 for dual phone line
75 Volts for protecting against surges between center and shield
75 Volts for p against surges between center and shield
rotecting
APPLICATION
For protection of phone, answering machines and fax with 2 phone lines
For protection of TV systems, cable box and DVR
For protection of security systems, CCTV and camera
3
5
Specifications and Applications
Model A
Size (HxWxD) (In) : 1.37" x 1.31" x 3.31" Weight: 0.11 Lb.
Model B
Size (HxWxD) (In) : 2.0" x 1.31" x 3.06" Weight: 0.11 Lb.
Model C
Size (HxWxD) (In) : 2.12" x 1.31" x 3.06" Weight: 0.16 lb.
6
Installation
1) SmartNet must be installed as close as possible to the equipment to be protected.
2. Turn off all equipment. 3 Unplug the RJ11/45, Coaxial or BNC cable from the equip­ ment you want to protect and plug into the "IN" jack on the SmartNet II. Plug the other end to the network jack or cable wall jack.
4. Plug the provided network cable (RJ11 or RJ45 only) to the "OUT" jack on the SmartNet II. Plug the other end of the pro­ vided network cable into the equipment you want to protect.
5. Connect the SmartNet unit to ground. See instructions on pages 8-11.
The SmartNet protects your equipment from surges that come through the data and signal line. To ensure that your equipment is completely protected, use a TBF™ power filter or UPS-TBF from Smart Power Systems.
7
Ground Connection - Model A
Plug directly into the receptacle in the wall outlet.
8
Ground Connection - Model C
9
Connect the ground wire with cable shoe to the equipment's metal chassis (ground) as shown below.
NOTICE: If metal chassis is not available, the ground wire with cable shoe should be connected to a proper ground.
Fig.2
Full System Connection
SN-BNC-A
BNC Cable
CAMERA
The equipment at both
ends of this cable are
protected by SmartNet II
Full System Installations
To protect an additional camera, monitor or any other equipment, use a separate SmartNet unit for each one.
To fully protect the equipment on the system, we recommend using one Smartnet unit at each end of the cable as shown above.
Lifetime Warranty
The SmartNet II unit is guaranteed to be free of defects in material and workmanship for its lifetime. If the product is defective, Smart Power Systems will repair or replace the product at its own discretion. Service under this warranty can only be obtained by your delivering or shipping the product with all shipping or delivery charges prepaid to:
Smart Power Systems
1760 Stebbins Drive
Houston, Texas 77043
There are no serviceable parts in the unit. The warranty will be void if the unit has been tampered with.
Fig.5
10
Full System Connection
11
CCTV
SN-BNC-C
BNC Cable
SECURITY
SYSTEM
SN-BNC-C
Returning a product to Smart Power
BNC Cable
13
If for any reason you need to return the SmartNet unit to Smart Power, you should obtain an RMA (Return Material Authorization) number before returning the unit.
To request an RMA number please call 800-772-7633 or visit the website at www.smartpowersystems.com under Support (RMA). Write the RMA number on the package and send the SmartNet unit with shipping or delivery charges prepaid to:
Smart Power Systems
1760 Stebbins Drive,
Houston, Texas 77043
Loading...