User Guide
Preliminary, 2015-10-02
Revision History
Version Date Changes
00 2015-10-02 Preliminary
USER GUIDE
1 OVERVIEW
Appearance
USER GUIDE
Accessories
Rubber case Quick Manual Vehicle Mounts
USER GUIDE
2 SPECIFICATIONS
PHYSICAL
Dimension(WxLxH) 117.3 x 65.8 x 17.1mm
Weight 90g
Indication Power on LED(Blue), Charging LED(Red), Tagging LED (Blinking Blue)
Battery 700mAh
Continuous Time 5 hours
Standby Time 24 hous
Charging Time 2 hous
RFID PERFORMANCE
RFID Reader Chip PHYCHIPS PR9200
Air Protocol EPCglobal Class 1 Gen 2 / ISO 18000-63 (formerly 18000-6C)
Interface Apple Lightning Connector
OS Apple iOS 7.0
Output Power
RFID Read Distance Up to 1.0m (depend on tags)
Antenna Circularly Polarized Antenna
RFID Function Read, Write, Lock, Kill
USER ENVIRONMENT
Operating Temp Discharge (-10 to 45°C), Charge (0 to 45°C)
Storage Temp -20 to 60°C (1 month), -20 to 45°C (3 month), -20 to 20°C (1 year)
Relative Humidity 5 to 95% humidity noncondensing
REGULATORY
RFID
EMI/EMC
Electrical Safety EN 60950-1
LIMITED WARRANTY
The lithium-ion battery capacity is dropping linearly to 80% over 300 cycles. A charge cycle means
using all of the battery’s capacity, but that doesn’t necessarily mean a full charge and discharge. The
lithium-ion battery in RFID reader should not be replaced by the user. Contact where you buy it.
316mW(25dBm) for US, EU and Korea band
200mW(23dBm) for Japan band
FCC Part 15 Subpart C 247, EN 302 208, KCC 2013-1, KCC 2012-102,
ARIB STD T107
EN 301 409-1, EN 301 409-3, EN61000-3-2, EN61000-3-3,
KN 301 409-1/3, KN61000-4-2/3/4/5/6/11
USER GUIDE
2.1 Charging
Vehicle mounts and RFID reader are shown below.
To charge the device, mounting the device to the vehicle mounts.
Note:
When the user connects the device with iPhone during the charging, the device can charge itself and the
device simultaneously.
When charging is finished, LED shall be turned off.
3 HOW TO USE DEVICE
Install the vehicle mount to your vehicle as shown below.
USER GUIDE
Connect iPhone to device as shown below.
Note:
This product is intended for use in vehicle mounting
Please do not use this product for portable use
USER GUIDE
4 HOW TO USE APPLICATION
4.1 How to install application in your iPhone
Once iPhone is connected to lightning connector, there will be pop-up to choose whether to start App or
not as picture above. If App is not installed, there will be a sign to download it from App-store. When you
accept the alarm, the App will be launched.
USER GUIDE
4.2 Launching the App
If iPhone and dongle device is connected properly, ‘Unplugged’ will be changed to ‘Plugged’. And
setting, read, clear, battery and stop button will be active.
4.3 Main Display
- Switch: Turn on or off the Reader
- Read Button: Start to read “Tag EPC”
- Clear Button: Remove Read Record
- Stop Button: Stop Tag Reading
- Display: Show Tag Read Record
4.4 Status Bar
USER GUIDE
The number of tags displayed
RFID READER Status
- Unplugged: RFID READER is not inserted into headset
jack.
- Plugged: RFID READER is inserted into headset jack.
- Connected: RFID READER is connected to app.
Battery gauge
4.5 Tag Read
1. Switch the button to "On"
2. Touch Read button to inventory tag continuously
A. PC + EPC will appear.
3. Touch Stop button to finish inventory tag
4. Touch Clear button to clear the list of tags.
USER GUIDE
USER GUIDE
5 CAUTION
5.1 Safety Information
1. Do not disassemble or repair arbitrarily but contact where you buy when RFID READER is in
trouble.
2. Do not use chemical substance(alcohol, benzene, detergent etc) and water to clean RFID
READER
3. Please avoid vibrations and shocks. Please place in a safe place when not in use.
4. Please avoid high/low temperature and high humidity.
5. Please turn RFID READER off in explosive area as there may be danger due to electric wave.
6. Please use medical device(pacemaker, hearing aid etc) which is blocked from RF energy.
7. Please stop using RFID READER and consult a medical expert in case of any allergic reactions
and side effect.
5.2 Operation
The device can be used over 20cm from the user.
This product is intended for use in vehicle mounting
Please do not use this product for portable use
1. The device will be automatically off from following situations.
2. When receives a phone call, the device automatically turn off the power.
3. Include a message, something pop-up by certain Apps.
4. When switching from Barcode App to other App or pressing Home button.
5. When pressing power button or the display automatically turns off to sleep mode or App display
disappears or the display is covered by Pop-up, it will automatically off the App.
5.3 RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment must be installed and operated with minimum distance of 20cm between the radiator and
your body. This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users.”
5.4 Compliance Information
FCC Information
Note: This equipment has been tested and found to comply with the limits for CLASS B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try correcting the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
USER GUIDE
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which receiver is
connected.
4. Consult the dealer or experienced radio/TV technician for help.
This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions
:
1. This device may not cause harmful interface, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
CE Information
This device is in compliance with the essential requirements and other relevant provisions of directive
1999/5/EC.
Japanese Radio Law
本機器は、電波法第 38 条の 24 第 1 項の規定に基づく認証を行ったものであることを証する。
USER GUIDE
FCC Information
This device complies with part 15 of the FCC Results. Operation is subject to the following
two conditions :
(1) This device may not cause harmful interface, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant
to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try correct the interference
by one or more of the following measures:
1.1. Reorient or relocate the receiving antenna.
1.2. Increase the separation between the equipment and receiver.
1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected.
1.4. Consult the dealer or experienced radio/TV technician for help.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
“CAUTION :
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment must be installed and operated with minimum distance of 20cm between the radiator and your body.
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm
may be maintained between the antenna and users.”
Exposure to Radio Frequency Radiation.
Loading...