SmartPool Inc PE13 User Manual
Table of contents
Important - Please read first
Rectangular or oval pools
Round pools
Installation
Pool Side Alarm Transmitter Assembly
Battery Installation
Low Battery Indication
Turn The Unit ON
Turn The Unit OFF
Reset The Unit
Sensor Calibration
T est The Unit
RF (Radio Frequency) Signal Link Testing
Transmitter channel A/B Select
Remote Receiver
Receiver Channel A/B Select
Back Up Po wer
How T o Connect To Your Home Security System
T roub le Shooting
PE-13 picture
2
3
3
4
5
6
6
7
7
7
8
8
8
10
11
11
12
12
14
Warranty
16
Sensitivity Adjust
5
PE13
IMPORTANT - Please read first
THIS PRODUCT DOES NO T REPLACE THE NEED FOR
ADULT SUPERVISION OF ALL PERSONS IN THE
POOL AREA. IT IS NOT A LIFE SAVING DEVICE. IT IS
AN AID TO A MULTI LEVEL PROGRAM OF POOL
SAFETY INCLUDING ADULT SUPERVISION,
KNOWLEDGE OF CPR AND SWIMMING
INSTRUCTION FOR ALL PERSONS USING THE POOL.
IT IS INTENDED FOR USE ON RESIDENTIAL
SWIMMING POOLS ONL Y AND THE MANUFA CTURER
ASSUMES NO RESPONSIBILITY FOR INJURIES OR
CONSEQUENTIAL PROPERTY D AMA GE WHILE THIS
PRODUCT IS IN USE ON A SWIMMING POOL.
PROPER INSTALLATION AND MAINTENANCE ARE
THE SOLE RESPONSIBILITY OF THE POOL OWNER.
!
WARNING:
To reduce the risk of injury to bathers,
or damage to your product:
!
Do not use if unit is damaged in any way.
!
Use this product only for its intended use as
described in this manual.
!
Unit must be submerged in water to operate
properly.
!
This product is not a life-saving device. It is
an aid to a multi-level protection program,
including adult supervision,
knowledge
of CPR
and swimming instruction for your child.
ALARM
If the water returning from the
filter is positioned at 6 oícloc k
and the flow is counterclockwise, the best location to put the
alarm is between 8 oícloc k to 9
oícloc k position.
On the other hand, if the flow is
clockwise, the alarm should be
placed between 3 oíclock to 4
oícloc k position.
ALARM
RETURN
from filter
Round pools
ALL POOLS
Do not point the eyeball
of the return towards the
center with the alarm at
the side. The flow from the
return will interfere, so the alarm
sensor cannot detect the wave motion properly .
W ARNING: Every pool condition varies, test
the alarm before use
RETURN
from filter
Place alarm in a
central location
for shortest
distance from all
parts of the pool
ALARM
Rectangular or oval pools
3
Installation
1. Take top seat cap of pool off and
remove the screws holding one end
of the top seat
2. Lift up one end of the top seat of pool
3. Hang the sensor tube onto the guide
rail. Back of the sensor unit should
rest against the inside of pool wall.
4. For wider guide rail, move the stainless bracket forward by removing the three
stainless steel screws and moving the
bracket.
5. Tighten the set screws on the stainless
steel mounting bracket against the pool
wall after inserting the plastic spacer to
protect wall
and liners.
6. Replace the
top seat
and top
cap.
For guide rail
up to 1.2î wide
For guide rail
up to 3/4î wide
Move
f
orwar
d
1
2
3
4
4
5
6
Sensitivity Adjust
Loosen the two screws on the
bottom of the sensor.
Move the plastic piece with the
pointer pointed to ìHî if you want
higher sensitivity or to ìLî if you
want lower sensitivity. The unit is
preset at factory to ìHî.
If you hav e to place the unit near
the return, snap the cap onto the
sensor cage facing the direction
of water flow .
NOTE: The deflector will reduce sensitivity .
Test the alarm unit as described in section
4.0 before use
Pool Side Alarm Assembly
The
POOLEYE
pool side alarm comes with a control head and a separate
sensor tube. Before the unit can be used, the two pieces must be
assembled together as follows:
Locate the phone jack at the bottom
of the control head, and a phone
plug coming out from one end of
the sensor tube. Place this phone
plug into the phone jack.
Gently push the tube into the bottom
of the control head. The sensor
tube end should fit snugly into the
bottom of the control head.
Loading...