smartmotion PACER GT User Manual
User Manual
PanerGT user manual.indd 1 7/21/2017 3:21:19 PM
Contents
1. Service Record
2. Assembly instructions
3. Main Specifications
4. Safe Riding Recommendations
5. Maintenance & Adjustment
6. Do’s and Don’ts
7. Display Panel
8. Display Panel Controls
9. Battery instructions
10. Warranty
User Manual
Congratulations for purchasing a SmartMotion electric
bicycle!
Please read this guide fully BEFORE using your electric
bike.
1. Service Record
In the Pacer GT box you will find the following items:
1. SmartMotion electric bicycle
2. Battery charger
3. 2X Pedals
4. 2X keys for battery lock
5. Front wheel quick release axle
6. Front light
7. Elastic strap
Check for damage
Adjust and Tension
Lubricate
Frame & Fork
Rims
Cables & connections
Spokes*
Gears
Seat
Reflectors & Lights
Handlebars, Stem, Grips
Brakes
Cranks & Bottom Bracket
Wheel Axles
All Fasteners
Chain
Derailleur
Seatpost
*Spokes to be tensioned to 130Nm
Model:
Serial Numbers:
Dealer:
Purchase Date:
6 Weeks/200km
Date:
Shop:
Mechanic:
6 Months
Date:
Shop:
Mechanic:
12 Months
Date:
Shop:
Mechanic:
24 Months
Date:
Shop:
Mechanic:
PanerGT user manual.indd 2-3 7/21/2017 3:21:22 PM
2. Fork
a. Slide the handle bar stem into the steering tube,
then fasten the centre screw using the 6mm allen
key to 6-8N.M. Turn the stem it to align it with the
forks correctly, then tighten the side pinch bolts to
6-8N.M. with a 5mm allen key to hold the stem in
the correct position.
b. Loosen the handle bar angle the four handlebar
clamp bolts and rotate the handlebar to make sure
the brake lever, shift lever and switch positions
are at the correct angle. Finally fasten the angle
adjusting bolt to 6-8N.M
2. Assembly Instructions
To Prepare
We recommend that you familiarise yourself
with the bike parts before assembling. Gather all
required tools. Be sure to work in a clean, dry space
with plenty of room. You might wish to lay down a
tarpaulin or old blanket to protect the bike during
assembly. You may find it helpful to stand the bike
frame on a block or sturdy box under the battery
housing to work with it in an upright position.
Please watch the balance when installing wheels.
1. Unpack
a. Carefully lift the electric bike out from the carton
(two people recommended for this task). Cut the
nylon zip ties with suitable scissors and remove the
foam protection from the bike.
b. Remove the front wheel and mudguard from the
bike and put them aside. Carefully stand the bike
upright, resting on its forks when installing wheels.
Your electric bike is shipped 85% assembled. Follow
these steps to get it ready and safe for you to ride.
Do not activate the brakes until the bike is
fully assembled. Squeezing brake levers
while calipers have no disc rotor between
them can damage the brakes.
2. Assembly Instructions
PanerGT user manual.indd 4-5 7/21/2017 3:21:29 PM
5. Bike Stand
Line up the stand with the holes near the left drop
out. Slide the bolts in and tighten. This is easier
to do when the stand is open with no weight on it.
6. Pedals
Attach the pedals to the cranks, paying attention
to the “L” or “R” marked on the pedal axles. Note:
the pedals have opposing threads – screw in the left
pedal counterclockwise and screw in the right pedal
clockwise. Install L pedal counterclockwise and the
right pedal clockwise.
2. Assembly Instructions
3. Mudguard
Install the front mudguard and front light on the
fork. Take off the bolt from the front fork, put the
front mudguard hanger mount on the inside or
outside of the fork then put the front light bracket
on. Put the bolt through the fork then fasten the
bolt with a 5mm allen key and 10mm spanner.
Then fasten the two mudguard stays to the forks.
Finally connect the light cable to the front light.
4. Light Connection
Finally connect the cable from the front light to the
cable connection coming out on the underside of
the down tube, making sure the arrows align before
pushing the connectors together.
2. Assembly Instructions
PanerGT user manual.indd 6-7 7/21/2017 3:21:41 PM
Loading...