Smartlock Digital SMARTPOINT SMARTLINC II 9160, SMARTPOINT SMARTLINC II 9150, SMARTPOINT SMARTLINC II Series User Operating Instructions Manual

USER OPERATING INSTRUCTIONS

SMARTPOINT SMARTLINC II

Biometric Recognition Safe Locking System

9160

AVAILABLE FEATURES

USER CODE

+ Open Lock
+ Change Code
+ Set Immediate Time Lock, if enabled
+ Time Lock Extension, if enabled

WRONG TRY PENALTY

+ Four (4) consecutive invalid codes initiates ve-minute delay

period. Two additional invalid codes will begin another ve­minute delay.

LOW BATTERY WARNING

MULTIPLE LOCKS

+ Up to Five

TIME DELAY

+ Programmable on each lock

- Delay Period: 1 - 99 minutes

- Open Period: 1 - 19 minutes

+ Two Time Delays Can Run At Once

DUAL CODE

+ Requires the presence of two users to open

+ Repeated audio and visual signal (LCD readout and repeated

beeping) during opening indicates back-up battery is low and

should be replaced.

AUDIO AND VISUAL SIGNAL

+ Double signal (LCD readout and unit beeps) indicates entry is

valid or accepted

+ Triple signal indicates invalid or not accepted

TIME LOCK

+ Immediate Time Lock (From now until next available open

period)

+ Time Lock Open Period Extension (Max. two (2) hours), if

enabled

CHANGING YOUR CODE - USER

ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN

1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.

2. Select lock if two or more locks are installed.

3. Enter “zero” six times

4. Enter existing six (6) digit code one time.

5. Enter NEW six (6) digit code two times (and scan nger, if set-up, after 2nd entr y).

+ If a valid code is entered, display will show “CODE CHANGED”

6. Test lock operation several times before closing the door.

7. If code update verication does not appear the old code is still valid. Wait 30 seconds and repeat

steps 1 - 6

9150

SELECT LOCK

XX

ENTER LOCK

X-X-X-X-X-X

OLD CODE

X-X-X-X-X-X

NEW CODE

X-X-X-X-X-X

CONFIRM NEW

X-X-X-X-X-X

CODE CHANGED

USING DURESS

The duress feature is available if the unit has been connected to an alarm system via a bat ter y/
alarm box. To use simply enter your code with the last number either + or - 1 or use the duress
nger print, if enrolled.
Example: Existing code (2-9-2-9-2-9)Duress code (2-9-2-9-2-8 or 2-9-2-9-2-0)

CONFIRM CODE

NOT MATCH

SMARTPOINT SMARTLINC II

This system is available with or without biometric identication ability. If using the SMARTLINC II, without biometric abilit y, please disregard
any reference, in these instructions, to ngerprints. The functionalit y of the two systems are identical except for the use of ngerprints
for identication.

V1.0_9102 | Division of Davcor Group Pty Ltd | www.smartlock.com.au | www.smartlock.co.nz | Page 1

USER OPERATING INSTRUCTIONS

SMARTPOINT SMARTLINC II

Biometric Recognition Safe Locking System

OPENING THE LOCK (WITH FINGER ONLY ACCESS WITHOUT TIME DELAY)

1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.

2. Select lock if two or more locks are installed, display will show “P TO SCAN, OK FOR CODE”.

3. Press P key, display will show “ SCAN YOUR FINGER”.

+ If a valid ngerprint is entered, display will show “LOCK = 1, OPEN!”.
+ If Lock is set with Open Oset, the display will show “LOCK = #, OFFSET = ##”, and will show the

counting sequence to the Oset.

4. Open the Door within 3 seconds.

+ Before power-o, display will show current date and time.

+ If an invalid ngerprint is scanned or the ngerprint was not placed directly on the scanner, the

display will show ”FINGERPRINT ERROR!”.

+ Display will power-o after 30 seconds of non-operation.

NOTE: IF THERE IS A LOCK SET TO AUTO OPEN - In a multiple lock system you can set an outer door lock to AUTO OPEN. This will allow the user (if

authorised) to open the inner compartment lock and have the outer door lock automatically open. The AUTO OPEN lock always opens rst.

NOTE: If there is a user who ngerprint is unable to be read, by pressing OK they can enter their code and scan their print . The
system will do a one-to- one match.

OPENING THE LOCK (WITHOUT TIME DELAY)

1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or “SELECT LOCK” when two or more locks are installed.

2. Select lock if two or more locks are installed.

SELECT LOCK

XX

P TO SCAN

OK FOR CODE

SCAN

YOUR FINGER

LOCK = 1

OPEN!

FINGERPRINT

ERROR!

SELECT LOCK

XX

ENTER LOCK

X-X-X-X-X-X

3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)

+ If a valid code/nger is entered, display will show “LOCK = 1, OPEN!”.
+ If Lock is set with Open Oset, the display will show “LOCK = #, OFFSET = ##”, and will show the

counting sequence to the Oset.

4. Open the Door within 3 seconds.

+ Before power-o, display will show current date and time.

+ If and invalid code is entered, display will show “NOT VALID USER!”.
+ If an invalid ngerprint is scanned or the nger was not placed directly on the scanner, the display

will show ”FINGERPRINT ERROR!”.

+ Display will power-o after 30 seconds of non-operation.

NOTE: IF THERE IS A LOCK SET TO AUTO OPEN - In a multiple lock system you can set an outer door lock to AUTO OPEN. This will allow the user (if

authorised) to open the inner compartment lock and have the outer door lock automatically open. The AUTO OPEN lock always opens rst.

OPENING THE LOCK (WITH TIME DELAY)

1. Press any key to power up SMARTPOINT.

+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.

2. Select lock if two or more locks are installed.

3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)

+ If Time Delay has been set, display will show “STARTING, TIME DEL AY” and then “LOCK = #, DEL AY
MM:SS”

+ Counting is updated ever y second, if displayed.
+ Press “P” to abort Time Delay, display will show “CANCEL, TIME DELAY? ” Press OK, display will

show, “TIME DELAY, CANCELLED”.
+ After Time Delay has elapsed, the display will show “P TO SCAN, OK FOR CODE” and then “#X
MM:SS, x-x-x-x-x-x” (open window counting time).

4. During the open window, enter a valid code (and scan nger, if set-up) to open.

+ If a valid code is entered, display will show “LOCK = 1, OPEN!”.

LOCK = #

OFFSET = ##

LOCK = 1

OPEN!

NOT VALID USER!

FINGERPRINT

ERROR!

SELECT LOCK

XX

ENTER LOCK

X-X-X-X-X-X

STARTING

TIME DELAY

LOCK = #

DELAY MM:SS

CANCEL

TIME DELAY?

V1.0_9102 | Division of Davcor Group Pty Ltd | www.smartlock.com.au | www.smartlock.co.nz | Page 2

USER OPERATING INSTRUCTIONS

SMARTPOINT SMARTLINC II

Biometric Recognition Safe Locking System

5. Open the Door within 3 seconds.

+ Before power-o, display will show current date and time.

+ If and invalid code is entered, display will show “NOT VALID USER!”.
+ If an invalid ngerprint is scanned or the nger was not placed directly on the scanner, the display

will show ”FINGERPRINT ERROR!”.

+ Display will power-o after 30 seconds of non-operation.
+ If using the Time Delay Override, enter USER code and touch nger, if set-up.

NOTE: During the Open Window the unit will beep 2 times every 10 seconds.

OPENING THE LOCK (WITH DUAL CODE - NO TIME DELAY)

1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.

2. Select lock if two or more locks are installed.

3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)

4. Enter a 2nd valid 6 (six) digit code (and scan nger, if set-up)

+ If a valid code is entered the LCD will display “LOCK = 1, OPEN!”.

5. Open the Door within 3 seconds.

+ Before power-o, display will show current date and time.

+ Invalid code will prompt LCD to display “NOT VALID USER”.
+ If an invalid ngerprint is scanned or the nger was not placed directly on the scanner, the display

will show ”FINGERPRINT ERROR!”.

+ Display will power-o after 30 seconds of non-operation.

P TO SCAN

OK FOR CODE

#1 MM:SS

X-X-X-X-X-X

LOCK = 1

OPEN!

NOT VALID USER!

FINGERPRINT

ERROR!

SELECT LOCK

XX

ENTER LOCK

X-X-X-X-X-X

2nd CODE

X-X-X-X-X-X

LOCK = 1

OPEN!

NOT VALID USER!

FINGERPRINT

ERROR!

OPENING THE LOCK (WITH DUAL CODE AND TIME DELAY)

1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.

2. Select lock if two or more locks are installed.

3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)

+ If Time Delay has been set, display will show “STARTING, TIME DEL AY” and then “LOCK = #, DEL AY
MM:SS”

+ Counting is updated ever y second, if displayed.
+ Press “P” to abort Time Delay, display will show “CANCEL, TIME DELAY? ” Press OK, display will

show, “TIME DELAY, CANCELLED”.
+ After Time Delay has elapsed, the display will show X MM:SS, x-x-x-x-x-x” (open window counting

time).

4. During the open window, enter a valid code (and scan nger, if set-up) , display will show “ENTER

CODE, X-XX-X-X-X”.

+ If a valid code is entered, display will show ““2ND CODE, X-X-X-X-X-X”.

5. Open the Door within 3 seconds.

+ Before power-o, display will show current date and time.

+ If and invalid code is entered, display will show “NOT VALID USER!”.
+ If an invalid ngerprint is scanned or the nger was not placed directly on the scanner, the display

will show ”FINGERPRINT ERROR!”.

+ Display will power-o after 30 seconds of non-operation.
+ If using the Time Delay Override, enter USER code and touch nger, if set-up.

NOTE: During the Open Window the unit will beep 2 times every 10 seconds.

SELECT LOCK

XX

ENTER LOCK

X-X-X-X-X-X

STARTING

TIME DELAY

LOCK = #

DELAY MM:SS

CANCEL

TIME DELAY?

#1 MM:SS

X-X-X-X-X-X

ENTER LOCK

X-X-X-X-X-X

2ND CODE

X-X-X-X-X-X

LOCK = 1

OPEN!

V1.0_9102 | Division of Davcor Group Pty Ltd | www.smartlock.com.au | www.smartlock.co.nz | Page 3

USER OPERATING INSTRUCTIONS

SMARTPOINT SMARTLINC II

Biometric Recognition Safe Locking System

5.0 Time Menu

TIME MENU

Time Menu allows the USER access to following functions if programmed during initial lock set-up:
NOTE: These functions are available only if one or more opening periods are stored in Time Lock Standard Week. Please see
Master Operating Instructions for more information on setting this up.

+ Immediate Time Lock - Immediate Closing until the next opening period.
+ Extension Time Lock (Active only if programmed through the PC) - Increase the open period. [30 Minutes at a time for a maximum of

two (2) hours.]

TIME MENU - IMMEDIATE TIME LOCK

Available only if programmed during initial lock set-up

1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.

2. Hold down “9” button, display will show “ACCESS, TIME MENU” then “ENTER CODE, X-X-X-X-X-X”.

3. Enter User code (and scan nger, if set-up).

+ If a valid code is entered, the display will show “IMMEDIATE TIME LOCK?”

4. Press OK to continue, display will show ”SELECT, T.L. SET = 1”

5. Press OK to continue, display will show “Do You CONFIRM?”

6. Press “OK” a 2nd time to conrm.

+ If the list of Time Lock Standard Week is empty, the function is unavailable and the display will
show ”LOCK = #, NOT VALID.”

TIME MENU - TIME LOCK EXTENSION

Available only if programmed during initial lock set-up

To access the TIME MENU

1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.

2. Hold down “9” button, display will show “ACCESS, TIME MENU” then “ENTER CODE, X-X-X-X-X-X”.

3. Enter User code (and scan nger, if set-up).

+ If a valid code is entered, the display will show “IMMEDIATE TIME LOCK?”

4. Press “P” to select next function, display will show ”EXTENSION TIME”

5. Press “OK” to continue, display will show ”SELECT LOCK, NUMBER = #”

SELECT LOCK

XX

ENTER LOCK

X-X-X-X-X-X

2nd CODE

X-X-X-X-X-X

LOCK = 1

OPEN!

NOT VALID USER!

FINGERPRINT

ERROR!

SELECT LOCK

XX

ENTER LOCK

X-X-X-X-X-X

IMMEDIATE

TIME LOCK?

EXTENSION TIME

SELECT

T.L. SET = 1

6. Press “OK” to conrm, display will show “EXTENT. TIME, 0 MIN”.

7. Press “P” to change the extension time in 30 minute increments. Press P once for 30 minutes, t wice

for 60 minutes, three times for 90 minutes and four time for 120 minutes.

8. Press “OK” to conrm, display will show “EXTENSION SET!.”

+ If the list of Time Lock Standard Week is empty, the function is unavailable and the display will
show ”LOCK = #, NOT VALID.”

CAUTION: If a mistake is made inserting Time and Date values, DO NOT CONFIRM. Instead, press P to cancel and repeat the steps
from the beginning.

NOTE: Time Lock Extension can only be implemented one time per time lock period. For example, if the extension needed is 60 minutes,
it must be entered as 60 minutes, not 30 minutes and then par t way through the 30 minute extension extend it another 30 minutes.

V1.0_9102 | Division of Davcor Group Pty Ltd | www.smartlock.com.au | www.smartlock.co.nz | Page 4

EXTENT. TIME

0 MIN

EXTENSION SET!