US Mini Plug User Manual
Safety
Please read all of the safety and operating instructions before using your device:
1. The Products are only for indoor use.
1. Do not disassembly the device or attempt to repair.
2. Plug the power cables into properly grounded electrical outlets in order to help
prevent against electrical shock.
3. Disconnect the power before you clean the device.
4. The devices are not suitable for use in situations or environments where failure,
delay or errors or inaccuracies in the data or information provided by the devices
could lead to death, personal injury or severe physical or environmental damage,
including without limitation in connection with the operation of nuclear facilities,
aircraft navigation or communication systems, air traffic control, or life support
systems.
Specification
Model No: SPG-US-02
Input/ Output: 120V AC, 50/60Hz, 15A
Temperature: 0℃ to 40℃ (Operating) , -20℃ to 65℃(Storage)
Humidity: 10% to 90% Non-condensing (Operating), 5% to 90% Non-condensing (Storage)
Installation and Setup of SmartiBlue Devices
To install SmartiBlue app
Step 1:
Download the SmartiBlue app from App Store® or Google Play™.
Once SmartiBlue app is installed, launch the app. Make sure your mobile device are
connected with Wi-Fi and Bluetooth.
Step 2:
Log into your Smart iBlue account, or sign up a new account by following the
instruction in the app.
Step 4:
After you have logged in your account, tag ‘+’ icon in the home page of your Smart
iBlue app
Instruction For US Mini Plug
Step 1:
Plug your Mini Plug into an available outlet and power on the plug, the small LED
light at the top will blink steadily, waiting to be associated with your mobile device.
Step 2:
In ‘My Device’ page, tap -‘Search Device’ to search the device and finish the
association process. You can also name your device after you clicked on it.
The small LED light at the top will blink blue rapidly when associating. The light
becomes solid blue when the device associated successfully. The notice would be
popped out to indicate that the association process is finished. The plug will be
shown on the ‘Associated Devices’ list if associated successfully. Tap the ‘return’ icon
in the top left corner
Step 3:
In the home page you will see the name of the associated plug. It means you have
successfully associated the plug. Now you can tap the plug to enter the control panel.
Here is the control panel. You have successfully set up your Smart iBlue Mini Plug
now.
Note
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—
Reorient or relocate the receiving antenna.
—
Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—
Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. such modifications could void the
user's authority to operate the equipment.
To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed
and operated with a minimum distance of 20cm between the radiator and your body.
Loading...