User Manual
Over Hadstenvej 40, DK-8370 Hadsten
Phone +45 89606100, Fax +45 86982522
Certified in accordance with ISO 9001
MAN BGP-COD-BAT rev.10-07.07
15-029-276
Programming unit
Type BGP-COD-BAT
Mode of operation
The BGP-COD-BAT is a port able pro gram ming unit used for
read ing or pro gram ming chan nel code(s) in the ASIC- based
series of smart-house products.
Once the bat tery is installed, the BGP-COD-BAT is ready for use.
Con nect the cable be tween the pro gram ming unit and a smarthouse mod ule type G..
5 keys pro vide the means of oper at ing the BGP-COD-BAT: two
keys are used for read ing and pro gram ming, two keys for
chang ing Groups and Channels and one key for select ing the
desired Input/Out put.
The cur rent cod ing is dis played by 4 x 8 LEDs. The top row of
LEDs dis plays the select ed input or out put. The two mid dle rows
dis play the cur rent channel group, while the bot tom row dis plays the cur rent channel code.
« In/Out » - Key
This key is used to scroll through the I/O's of a module. If a new
mod ule is connect ed or if con sec u tive channel codes are allo cat ed to the I/O's, press ing the « In/ Out » key has no effect
since all smart-house mod ules are pre programmed to their
phys i cal num ber of inputs/out puts. This key is also used to
switch between con sec u tive and individ ual cod ing of the I/O's.
To change the mode, keep «
In/Out » pressed for more than 2
sec onds.
« Group » - Key
Used to select the Group ad dress with in the range A to P. The
Group LED will shift one posi tion right for each key acti va tion.
« Chan nel » - Key
Used to select the chan nel(s) with in the group. The Channel
LED will shift right one, two or four posi tions, depending on the
number of inputs/out puts. If con sec u tive channels are select ed, then pressing the « Chan nel » key will have no effect.
« Read / On » - Key
Used to turn on the BGP-COD-BAT and to read the chan nel
codes of the con nect ed mod ule. When the read ing is complet ed, the dis play will show the chan nel code of the module: either
1, 2, 4 or 8 inputs/out puts.
2, 4 or 8 In/Out LED's being ON indi cates that con se cutive
chan nel codes are allocat ed to the I/O's, e.g. input 1 cod ed to
P1, input 2 to P2 input 8 to P8.
If only one In/Out LED is ON, then the I/O's are cod ed individ u al ly, e.g. input 1 to C5, input 2 to D4 etc. The code for each
I/O is
indi cat ed by a group LED and a chan nel LED.
If the BGP-COD-BAT is not connect ed to a smart-house system,
it will turn off with in two se conds.
15-029-276_BGP-COD-BAT MAN.qxp:BGP-COD-BAT MAN 9/25/07 11:52 AM Page 1
« Prog » - Key
When the dis played I/O-cod ing cor re sponds to the de sired
chan nel con fig u ra tion, the codes will be down load ed to the
smar t-house mod ule when press ing the « Prog » key.
After pro gram ming is execut ed, a ver ifi ca tion takes place. If this
ver ifi ca tion fails, all acti vat ed LEDs in the display will flash two
times, and the pro gram ming unit will switch off.
If such beha vi our occurs repeat ed ly on the same module, the
mod ule may be faulty. If sev er al mod ules fail to down load, the
BGP-COD-BAT may be faulty.
Indi vid u al In/Out chan nel pro gram ming
The BGP-COD-BAT fea tures an addi tion al mode of sin gle-chan nel
edit ing. Press ing « In/Out » for more than 2 seconds will
change the oper ating mode to sin gle point pro gram ming. The «
In/Out » key is now used to select one of the eight pos sible
inputs/out put, thus mak ing indi vid u al chan nel cod ing pos sible.
The In/Out-LEDs assign the dis play chan nel code to the cor re
-
spond ing phys i cal input/out put of the mod ule.
In sin glemode the « Channel » key also has the abil ity to dis able
an In/Out-posi tion. « Chan nel » must sim ply be pressed past
chan nel 8, where by both the Chan nel LED and the Group LED
will turn off. To re enable, just press « Chan nel » again.
It is pos sible to change all eight Inputs/Out puts, even though
some smart-house modules are built for only 1, 2 or 4
Inputs/Out puts.
To exit sin gle chan nel program ming, just keep the
« In/ Out » key pressed for 2 seconds.
Out put stat us set ting
On receiv ers it is pos sible to con fig ure the stat us of the out puts
dur ing smart-house fail ure. Nor mal ly, any out put of a receiv er
will go off dur ing smart-house fail ure. In some cas es the invert ed func tion is desir able (e.g. light appli ca tions - turn on light if
the smart-house is down).
To change out put stat us, the BGP-COD-BAT must be put into
con fig u ra tion mode. This is done as fol lows:
• Remove any con nect
ed smart-house system.
• Keep both « In/Out » and « Group » pressed, while press ing
« Read/On ».
The first In/Out LED now turns on. Con nect the smart-house
system, and press « Read/On ». If out put stat us is set, then
chan nel LED 1 will illu mi nate. Press ing « Chan nel » will tog gle
the out put stat us On/Off.
Press « Prog » to store.
If « Read/On » is pressed when no smart-house system is con nect ed, the LEDs will flash to indi cat ed a false con di tion. Only a
suc cess ful read ing will reset this con di tion.
Oth er fea tures
To code a smart-house mod ule off-line, nei ther smart-house nor
pow er to sup ply the mod ule is required. Sim ply con nect the
mod ule to the pro grammer and start cod ing.
If On-line cod ing (mod ule connect ed to an oper at ing smarthouse system) is per formed, the mod ule auto mat i cal ly discon nects ifself from the smart-house and returns to normal oper a tion after the program mer cable is dis con nect ed.
The BGP-COD-BAT auto mat i cal ly turns off when no key has been
pressed with in the last 30 sec onds.
If the con nec tion cable is removed from the smar t-house
module, the BGP-COD-BAT will switch off with in 2 sec onds.
Low bat tery indi ca tion
When bat tery is low, the In/Out row of LEDs will roll cen ter wards in an eye-catch ing man ner.
Warning
When using the BGP-COD-BAT you must connect the cable to
the BGP-COD-BAT before connecting the cable to any smarthouse module that is to be coded. Even so, the cable must first
be removed from the smart-house module before disconnecting
it from the BGP-COD-BAT.
Without observing these precautions you may destroy the ASIC
inside the smart-house module through static discharges.
Cau tion
To ensure long bat tery life, always remem ber to remove the
cable from the smart-house mod ules. The smart-house
modules will be kept in an inac tive state as long as the BGPCOD-BAT is con nect ed.
Addi tion
al infor ma tion
Scope of sup ply:
1 x pro gram ming unit
BGP-COD-BAT
1 x cable
GAP CAB
1 x user man u al
MAN BGT-COD-BAT
Not sup plied:
1 x 9 V bat tery type 6LR61
15-029-276_BGP-COD-BAT MAN.qxp:BGP-COD-BAT MAN 9/25/07 11:52 AM Page 2
Loading...