Page 1
by Bkav
MODEL: SH - CC6W
Page 2
www.smarthome.bkav.com
Copyright © 2015 Bkav SmartHome Co., Ltd. All rights reserved.
8936 04393UGCC 6W
Mfr Code:
UGCC6W/V1.1/1015
Page 3
USER GUIDE
6-CHANNEL CONTROL PANEL
SH - CC6W
Bkav SmartHome technology company limited
Page 4
Usage notice
Thank you for choosing 6-channel control panel SH - CC6W of Bkav SmartHome. By selecting Bkav SmartHome’s
products, you will get the best warranty service and installation support from our technicians.
This document gives useful information during installation and usage time. You should read and keep the manual
carefully in case of need.
Electric shock may cause injuries or threats to life. Before installing, repairing or cleaning the
device, you should check whether the device’s power is disconnected.
This work should be done by technicians or Customer Contact Center to avoid electric related
Warning
6-channel control panel SH - CC6W is the product of Bkav SmartHome and has been registered regarding
design, utility solutions and quality certification. All violations such as copies of design and product idea are
subject to the current copyright law of the Socialist Republic of Vietnam.
accidents.
Environmental regulations must be complied when discarding or recycling the device or its
wrapping.
Copyright © 2015 Bkav SmartHome Co., Ltd. All rights reserved.
1
Page 5
2
Table of contents
Usage notice
Table of contents
Safety instruction
Introduction
General introduction
Product package
Specifications
Device usage
Overview
LCD screen
Turn on/off the device - Forcible turn-on and Auto mode
Turn on/off air conditioner – Select operating mode
Adjust temperature – Adjust fan speed – Adjust wind direction
Turn on/off relay channels - Turn on/off triac channels
Switch preferred preset mode
Select preferred mode – Reset Wi-Fi information for the device
Usage of remote control SH - RM6
Turn on/off the device - Select preferred scenario
Wiring diagram
1
2
4
5
5
6
7
8
8
9
10
11
12
13
14
15
16
16
17
Page 6
3
Installation instruction
Insert Power control box into Receptacle box
Mount the stainless steel mounting frame
Mount control touch-screen onto the frame
Software installation instruction
Contact
16
18
21
22
23
24
Page 7
4
Safety instruction
Do not use voltage which is different from the one stated in the device’s specifications.
Disconnect device’s power prior to any installation, disassembly or repair.
Do not leave the device in high-temperature environment.
Do not disassemble the device if not necessary.
Do not clean the device with corrosive chemicals.
Safety instruction should be complied during the device usage.
Warning
Page 8
Introduction
General introduction
SH - CC6W is a smart touch-screen control panel integrated with Wi-Fi. It can control lighting systems, curtains,
blinds, air conditioners (*) and create scenarios based on users’ demands.
With capacitive touch technology, anti-scratch Gorilla Glass, unibody aluminum cover, LCD screen, the device will
make your house modern and luxurious.
With Wi-Fi technology, users can connect and control SH - CC6W via mobile devices connected to Wi-Fi and
internet from anywhere, even when you are not at home.
The product is suitable for controlling home appliances such as: group of lights, fans, water heaters, aquariums,
air conditioners, etc.
(*) The device can only control air conditioners via control device SH - IRW.
Note:
5
Page 9
6
Product package
Control touch-screen
Power control box
Receptacle box
User guide (book)
Stainless steel
MODE 2 MODE 3 MODE 4
MODE 1
mounting frame
Remote control
SH - RM6
SET
(battery included)
2 Wire connectors
by Bkav
Connecting cable
MODEL: SH - CC6W
and screws
Page 10
Specifications
7
Voltage
Operating temperature
Wifi band
Output power rating 4 relay channels 220VAC 15A max
Dimensions of Power control box
Weight of Power control box
Dimensions of Control touch-screen
Weight of Control touch-screen
100-240V 50/60Hz
60ºC max
802.11n - 2.4Ghz
2 triac channels 220VAC 15A max
140 x 90 x 55 mm
420 gram
180 x 120 x 8,6 mm
290 gram
Page 11
8
Device usage
Overview
Button to control relay channels
LCD screen
Button to control
wind fan
Triac 1 button
Button to increase/
decrease fan speed
or temperature
Triac dimming
level indicator
Button for overall
forcible turn-on/off
Button to decrease output
power of triac channel
MODE 2 MODE 3 MODE 4
MODE 1
Button for
preferred modes
Button to increase output
power of triac channel
Indicator light
Button to control
air conditioner
Triac 2 button
Button to switch air
conditioner modes
Button for forcible
/Auto turn-on
Page 12
LCD screen
Wind direction
Air conditioner modes
Wind speed
9
DD - MM - YYYYTime Date
Outdoor
humidity
Outdoor
temperature
Air conditioner
temperature
Indoor
humidity
Indoor
temperature
Page 13
10
Turn on/off the device
Tap on Power button < > to turn on/off the device:
When the indicator light is off, tap on Power button < > to turn on the device.
When the indicator light is on, tap on Power < > to forcibly turn off the device.
Forcible turn-off mode is the turn-off time in a certain period.
Notice
Forcible turn-on and Auto mode
Tap on < > to select Forcible turn-on or Auto mode:
When the indicator light is on, the device is in Forcible turn-on.
When the indicator light is off, the device is in Auto mode.
In forcible turn-on mode, the device’s operation does not depend on
human sensor.
Auto mode operates based on human sensor.
Notice
The device works automatically only when combined with human
sensor SH - D2W.
Indicator light
Indicator light
Page 14
Turn on/off air conditioner
Tap on < > to turn on/off air conditioner:
When the air conditioner is in turn-on mode, icons [ ]
will be displayed.
When the air conditioner is in turn-off mode, icons [ ]
will be hiden.
The device just controls the air conditioner when installed with air conditioner controller SH - IRW.
Notice
Select the operating mode
Tap on Mode button < > to select:
[ ] Drying mode.
[ ] Cooling mode.
[ ] Warming mode.
[ ] Auto mode.
11
Page 15
12
Control temperature
Tap on < > to increase.
Tap on < > to decrease.
Buttons to adjust temperature works only when the
Notice
mode to adjust fan < > is disable.
Control fan speed
Tap one time on fan mode < >:
The icon [ ] flickers.
Tap on < > to increase the fan speed.
Tap on < > to decrease the fan speed.
Icon < > is moving, fan is in Auto mode.
Control wind direction
Tap 2 times on fan mode < >:
The icon [ ] flickers.
Tap on < > to adjust wind direction upward.
Tap on < > to adjust the wind direction downward.
Icon [ ] is moving, the wind direction is in Auto mode.
Page 16
Control relay channels
Tap on one of the following buttons < >
to turn on/off the corresponding channels:
The indicator light below the icon is on, the status is On.
The indicator light below the icon is off, the status is Off.
13
Each control channel can be adjusted to control any power
channel of Power control box by software reconfiguration.
Notice
Control triac channels
Tap on < > to turn on/off the corresponding channels:
Tap 1 time if the corresponding channel is off, the indicator
light below the icon will flicker. Simultaneously, line of indicator
lights between < > will be on.
Tap on < > to decrease output power rating.
Tap on < > to increase output power rating.
The indicator light line between < > represents output
intensity. Each light is equivalent to 10% of output.
To turn off one channel, tap on the corresponding button twice.
MODE 1
MODE 1
MODE 2 MODE 3 MODE 4
MODE 2 MODE 3 MODE 4
Page 17
14
Switch preferred preset modes
To setup a preferred mode, take the following steps:
Lighting mode and devices can be adjusted to meet demands.
Tap on one of the following icons and hold for more than 3 seconds:
MODE 1 MODE 2 MODE 3 MODE 4
< > < > < > < >
The corresponding indicator of the icon flickers.
MODE 1
MODE 2 MODE 3 MODE 4
Default < > is the sleeping mode of the device. In this mode, lights will not automatically turn
MODE 1
off if there is no signal from human sensor.
Time to auto turn-off lights if there is no signal from human sensor to other modes can be setup on
Notice
the control software of the device.
Page 18
Select preferred modes
To select a preferred preset mode, tap on the corresponding modes:
Tap on < > to select preferred Mode 1.
Tap on < > to select preferred Mode 2.
Tap on < > to select preferred Mode 3.
Tap on < > to select preferred Mode 4.
MODE 1
MODE 2
MODE 3
MODE 4
Reset Wi-Fi information for the device
To reset Wi-Fi information (input connected device) including Wi-Fi
name and new password, take the tasks as below:
Tap and hold < > for 15 seconds until there is a notification
sound and restart to access the new settings.
MODE 1
MODE 1
15
MODE 2 MODE 3 MODE 4
MODE 2 MODE 3 MODE 4
Page 19
16
Use remote control SH - RM6
Turn on/off the device
Press Power button < > to turn on/off the device:
When the indicator light is off, press Power button < > to turn on the device forcibly
When the indicator light is on, press Power button < > to turn off the device forcibly.
Select preferred scenarios
To select preferred scenario with a remote control:
Press button <1> select scenario < >.
Press button <2> select scenario < >.
Press button <3> select scenario < >.
Press button <4> select scenario < >.
Press < > select Forcible turn-on or Auto mode.
SET
MODE 1
MODE 2
MODE 3
MODE 4
SET
1
4 2
3
SET
Page 20
L
N
Line
Neutral
100-240V 50/60Hz
Wiring diagram
17
100-240
VAC
C1 C2 C3
N
L
C1
SS
N
5A 5A 15A 15A 15A 15A
Input
C4 C5 C6
C2 C3 C4 C5 C6
Output
Page 21
18
Insert Power control box into Receptacle box
Step 1: Remove the screw hole
covers (3) from Power control box
(2).
Step 2: Connect wires to their
wire connectors (4) based on the
wiring diagram on Page 17, and
connect the connectors to their
corresponding locations on Power
control box (2).
The order of wire connec-
tors is symbolized on the
Note
device’s cover.
Requirement: Remove the
screw hole covers (3) gently
with suitable tool to avoid
scratching the box’s cover.
Installation instruction
1
4
Wire connector
3
Screw hole cover
2
Power control box
1
Receptacle box
Page 22
Step 3: Insert Power control box
(2) into Receptacle box (1), then
fasten 4 M4 screws (5).
5
M4 screw
19
Requirement: Power control
box (2) must be tightly mount-
ed on Receptacle box (1).
2
Power control box
1
Receptacle box
2
Page 23
20
Step 4: Insert the screw hole
covers (3) into their correspond-
ing holes.
3
Screw hole cover
Requirement: The screw hole
covers (3) must fit in their holes,
should not be loose and wobbly.
Connection wires should be
arranged neatly and tied firmly
with cable ties.
Step 5: Connect the connecting
cable (7) to Power control box
(2).
The green part of the
connecting cable should
Notice
face outwards.
2
Power control box
1
Receptacle box
7
Connecting cable
Green part of the connecting cable
3
Page 24
Mount the stainless steel mounting frame
Mount the stainless steel mount-
ing frame (6) onto Receptacle box
(1). Neatly place the frame (6) on
the wall before tightening it by 4
M4 screws (5).
Requirement: The stainless
steel mounting frame (6) must
be neatly and tightly placed
without horizontal deviation by
Level ruler.
21
Stainless steel
6
mounting frame
M4 screw
5
1
Receptacle box
4
Page 25
22
Mount the control touch-screen onto the stainless steel mounting frame
Step 1: Put the control touchscreen
(8) in parallel with the mounting
frame (6). Connect the Connecting
cable (7) to the panel (8).
The green part of the
connecting cable should
Notice
face outwards.
Installation direction of Control touch-screen
b
a
Step 2: Install the control
touch-screen (8) following the
arrow’s direction (a) into the
mounting frame (6).
Step 3: When the control
touch-screen (8) and the mount-
ing frame (6) fit together, push
MODE 1
MODE 2 MODE 3 MODE 4
following the arrow’s direction (b)
until the sound of snap.
The control touch-screen
(8) must be installed firmly
Notice
and neatly on the wall and
5
without horizontal deviation.
8
Control touch-screen
7
Connecting cable
6
Stainless steel mounting frame
2
Power control box
1
Receptacle box
Page 26
Software installation instruction
You can download Bkav SmartDevice to control the device at:
http://www.smarthome.bkav.com/SmartDevice
or scan QR Code below to download the application.
23
Page 27
24
If there is any problem related to the product, please contact Customer Contact Center:
Contact
Customer Contact Center: (+1) 202 386 6779
Email: GlobalProject@bkav.com
Page 28
The new homes standard !
Loading...