Smartguard Motio Light with Video Camera User Manual
Table of contents
1. Contents of pack age
...............................................................................
Page 1
2. Smartguard™ Motion Light with Video Cam era
...........................
Page 3
3. A ssem bly
....................................................................................................
Page 3
4. Installation
.................................................................................................
Page 4
5. Programming your Smartguard™
........................................................
Page 8
6. Set the date and time of Smartguard™
..............................................
Page 11
7. Viewing video
...........................................................................................
Page 12
8. Technical Specifications
........................................................................
Page 13
9. General Information and Safety
...........................................................
Page 14
10. FCC inform ation
....................................................................................
Page 15
11. FAQ (Frequently Asked Questions) Section
.................................
Page 16
Contents of packaging
• Smartguard™ Motion Light with Video Camera
• User Manual
• 1 Allen key
• lpc 300W halogen light bulb
• SD card
• Accessory bag: 2pcs screws, 2pcs plastic masonry plugs, wall
mount (cross bar), 3pcs wire nuts
(User manual and alien key are kept in one zip bag, please keep these
accessories. If all contents are not present upon opening the packaging
call 1-877-482-2484 or visit www.sm art-guard.net)
Smartguard™ Motion Light with Video
Camera overview
Step 1. Assembly
1. Install/replace the halogen lamp (see fig. 3)
■ Make sure to unplug unit or turn off power first.
■ Remove floodlight cover by unscrewing floodlight screws
using a Phillips head screw driver.
■ If replacing a bulb, take out the existing halogen light bulb
(part no.®)
■ Put in new 300 W att maximum halogen light bulb (part no.®).
■ Replace floodlight cover tightening screws carefully.
* Caution: Never touch the bulbs with your bare hands.
Always use a clean cloth when handling the bulbs.
Fig. 3
Step 2. Insert/remove SD card (see fig. 4):
■ Unscrew the waterproofed cover using provided Allen key
(part no.©), then insert the SD card (part no.®) until it
automatically locks into place.
■ If you need to rem ove the SD card (part no.®), please press
OFF button and take it out within 30 seconds.
■ When LED light turns green, meaning SD card (part no.®) is
being read, do not remove SD card (part no.® ) or data may be
lost.
■ To rem ove SD card (part no.®), push in SD card (part no.®)
once to eject, then pull out.
Step 3. Installing the SmartguardrM Motion
Light with Video Camera
IMPORTANT
IF IN ANY DOUBT A BOUT THE INSTALLATION OF THIS PRODUCT, CONSULT A
QUALIFIED ELECTRICIAN
- This product must be grounded
- Do not mount the unit against inflammable surfaces
- The motion detector will not operate correctly if it is installed:
® Near the outlet o f a central heating boiler
© Near air conditioning plant
© Pointing directly at moving vehicles
® W ithin sight o f reflections from moving water
© Where other lamps could shine on the detector
BEFORE ATTEMPTING ANY INSTALLATION OR MAINTENANCE, ENSURE THAT
THE ELECTRICAL SUPPLY IS SW ITCHED OFF AND THE CIRCUIT FUSES
REMOVED OR THE CIRCUIT BREAKER IS IN THE OFF POSITION.
Please make sure the voltage and polarity are correct before connection.
Incorrect voltage may cause electric shock. If you are not sure, please
contact your retailer.
Note: It is recommend to mount Smartguard™ Motion Light with
Video Camera 6 - 7ft above the ground for optimum performance,
do not mount the fixture below 3.94ft. See below figure for details of
performance range.
Detection range: 32.8ft x 180° (see fig. 5)
Installation to a junction box using crossbar mount
(see fig. 6 & fig. 7):
1. Attach the crossbar (part no.® ) to junction box and fix by screw C.
2. Feed the cable through the back mounting plate.
3. Fix the mounting plate to crossbar (part no.®) by screw D
4. Connect the black wire (live wire) from the AC power cord to the
single black wire coming from Smartguard™ using one o f the supplied
wire nuts (part no.®).
5. Connect the white wire from the AC power cord to the white wire
coming from SmartguardIM using one of the supplied wire nuts (part
no.®).
6. Connect the green/yellow wire from the AC power cord to the *
green/yellow wire coming from Smartguard™ using one o f the
supplied wire nuts (part no.®).
7. Make sure the polarity is correct.
8. Attach the unit to the mounting plate. You will first need to angle the
unit back so that the catch at the top of the mounting plate fits into slot
on the back of the unit. Next lower the unit until holes at the bottom of
the mounting plate and unit are flush. Then screw (screw A) into this
hole, tightening carefully.
Fig. 7
Loading...