Smartguard AEC-931A2BSD-SP4 User Manual

User Manual
AEC-931A2BSD-SP4 Smartguard Motion Light with Video Camera
Table of contents
1. Contents of package ................................................................... Page 1
2. Smartguard Motion Light with Video Camera ........................... Page 3
3. Insert/remove memory card ........................................................ Page 3
4. Installation .................................................................................. Page 4
5. Programming your Smartguard .................................................. Page 7
6. Set the date and time of Smartguard ........................................... Page 9
7. Viewing video............................................................................. Page 11
8. Technical Specifications ............................................................. Page 12
9. General Information and Safety .................................................. Page 13
10. FCC information ....................................................................... Page 14
11. FAQ (Frequently Asked Questions) Section ............................ Page 15
Contents of packaging
Smartguard Motion Light with Video Camera User Manual 1 Allen key Memory card Accessory bag: 2pcs screws, 2pcs plastic masonry plugs, wall
mount (cross bar), 3pcs wire nuts
(User manual and allen key are kept in one zip bag, please keep these
accessories.)
① ②
U se r M a nu a l
S m a rt g u ar d M o t io n L i gh t w it h V id e o C a m e r a
Smartguard
Memory Card
User Manual
④ ⑤
Allen Key
Screws
Screw D
Plastic Masonry
plugs
Wall Mount
(Cross Bar)
Wire nuts
Smartguard Motion Light with Video Camera overview
Step 1. Insert/remove memory card (see fig. 3):
Unscrew the waterproofed cover using provided Allen key
(part no.), then insert the memory card (part no.) until it automatically locks into place.
If you need to remove the memory card (part no.), please
press OFF button and take it out within 30 seconds.
When LED light turns green, meaning memory card (part no.
) is being read, do not remove memory card (part no.) or
data may be lost.
To remove memory card (part no.), push in memory card
(part no.) once to eject, then pull out.
Fig. 1
Fig. 3
Fig. 2
LED lamphead
Wnterproofed cover
LED Indicator
Camera lens
PIR lens
Step 2. Installing the Smartguard Motion Light with Video Camera
IMPORTANT
IF IN ANY DOUBT ABOUT THE INSTALLATION OF THIS PRODUCT, CONSULT A QUALIFIED ELECTRICIAN
- This product must be grounded
- Do not mount the unit against inflammable surfaces
- The motion detector will not operate correctly if it is installed:
Near the outlet of a central heating boiler Near air conditioning plant Pointing directly at moving vehicles Within sight of reflections from moving water Where other lamps could shine on the detector
BEFORE ATTEMPTING ANY INSTALLATION OR MAINTENANCE, ENSURE THAT THE ELECTRICAL SUPPLY IS SWITCHED OFF AND THE CIRCUIT FUSES REMOVED OR THE CIRCUIT BREAKER IS IN THE OFF POSITION.
Please make sure the voltage and polarity are correct before connection. Incorrect voltage may cause electric shock. If you are not sure, please contact your retailer.
Note: It is recommend to mount Smartguard Motion Light with Video Camera 6 – 7ft above the ground for optimum performance, do not mount the fixture below 3.94ft. See below figure for details of performance range.
Detection range: 32.8ft x 180 (see fig. 4)
Fig. 4
Installation to a junction box using crossbar mount (see fig. 5 & fig. 6):
1. Attach the crossbar (part no. ) to junction box and fix by screw C.
2. Feed the cable through the back mounting plate.
3. Fix the mounting plate to crossbar (part no. ) by screw D
4. Connect the black wire (live wire) from the AC power cord to the single black wire coming from Smartguard using one of the supplied
wire nuts (part no. ).
5. Connect the white wire from the AC power cord to the white wire coming from Smartguard using one of the supplied wire nuts (part no.
⑧).
6. Connect the green/yellow wire from the AC power cord to the
green/yellow wire coming from SmartguardTM using one of the supplied wire nuts (part no. ).
7. Make sure the polarity is correct.
8. Attach the unit to the mounting plate. You will first need to angle the unit back so that the catch at the top of the mounting plate fits into slot on the back of the unit. Next lower the unit until holes at the bottom of the mounting plate and unit are flush. Then screw (screw A) into this hole, tightening carefully.
Fig. 5
Screw D
Screw A
Screw C
Installing your Smartguard Motion Light with Video Camera on surface without a junction box. (see fig. 7 & fig. 8)
1. Place plastic masonry plugs (part no. ) into desired surface aligning holes as shown below. Using an electric screwdriver, fasten mounting plate directly to surface using screws E (part no. ).
2. Feed the cable through the back mounting plate.
3. Connect the black wire (live wire) from the AC power cord to the single black wire coming from Smartguard using one of the supplied wire nuts (part no. ).
4. Connect the white wire from the AC power cord to the white wire coming from Smartguard using one of the supplied wire nuts (part no ).
5. Connect the green/yellow wire from the AC power cord to the 2 green/yellow wires coming from Smartguard using one of the supplied wire nuts (part no. ).
6. Make sure the polarity is correct.
7. Attach the unit to the mounting plate. You will first need to angle the unit back so that the catch at the top of the mounting plate fits into slot on the back of the unit. Next lower the unit until holes at the bottom of the mounting plate and unit are flush. Then screw (screw A) into this hole, tightening carefully.
Fig. 6
Black
L
N
White
AC power cord
Screw A
Fig. 9
Screw E
Screw A
Please allow 1 minute warm-up time after switching on. * Push the RESET button after switching on.
Remove plastic lens cover from camera after installation.
(see fig. 8)
Step 3 Adjusting the Settings (see fig. 9-11)
Time control:Turn the
time control knob to+ side to increase the illumination time (7 minutes max.), turn the control knob to side to reduce the illumination time (5 seconds min.).
To perform a walk test turn the knob
fully to the - side until the indicator faces the W mark. When the walk test is completed adjust the knob to the + side to your desired lamp on time (we recommend this be at least 20 seconds to ensure lighting of the area is sufficient for recording – 20 seconds is marked as 20 on the product.
Fig. 7
Fig. 8
Sensitivity control:Adjust the detector range of Passive
Infrared Motion Sensor ( 6.56ft ~ 32.8ft)
Selecting working mode:
Mode 1: Suggested setting when out of town
- Light + camera + speaker: all day detection
- Daytime and nighttime: light, camera and speaker are all in operation
Mode 2: Suggested for day to day use
- Light at night + camera all day + speaker in the daytime
- Daytime: light is off, camera is on, speaker is on
- Nighttime: light is on, camera is on, speaker is off
Mode 3: Perfect for a place of business
- Light at night + camera all day + speaker at night
- Daytime: light is off, camera is on, speaker is off
- Nighttime: light is on, camera is on, speaker is on
Audio mode: for selecting which audio message will play
when motion sensor detects movement.
- Pre-set default is You are trespassing
- Push one time for Warning! You are being videotaped by a
security camera
- Push again for dog barking
- Push one more time to turn off this function
LED indicator:for indicating the function status of the unit
by different color LED lights.
1) Red memory card (part no.) is not inserted into the
memory slot or the system is malfunctioning. Please turn off and on the main power supply to the unit if the system is malfunctioning.
2) Green The unit is recording or USB is inserted
3) LED off: stand by (memory card is inserted into the slot,
when off/record button is pressed
4) Flash green LEDmemory card is full
* Usually meory card has override function, but if the user
Fig. 12
doesnt reset the date/time after power failure, the setting will return to default and lead to limited space for saving files. * Backup power for reserving date/time setting for at least 1 to 3 days during power outage. * Please note when off/record button is pressed, remove memory card (part no.) within 30 seconds (now the LED will turn red after memory card is removed from the slot)
Reset button: restore functions to default settings
1) Press RESET button once each time you turn on unit.
2) Please press this button in case of system malfunction.
Off/Rec:Please press OFF/REC button to remove meory card
(part no.). Please remove card within 30 seconds of pressing the OFF/REC button to avoid loss of data.
Step 4. Set the Date and Time
This will allow the security video taken by Smartguard to display the correct date and time it was taken.
1. Push TIME/DATE SET button (see fig. 12) for 3
seconds. The LCD screen will then flash 3 times, indicating you have entered Time/Date setting mode.
2. YEARsetting”Y” and “10” are displayed on
the screen; push the button to set year from 10­99”, push the button again and hold for 3 seconds
Fig. 10
Fig. 11
3 Position Switch
10
to scroll through numbers quickly. If you have not pressed the button for 3 seconds, it will automatically save the year and go on to allow you to set the month.
3. Repeat the same setting procedure for MONTH/DATE/HOUR/MINUTE.
4. VIDEO/PHOTO settingwhen entering this mode, these two
icons and V appear on the screenpush the button to choose VVideoor PPhoto. If you have not pushed any
buttons for 3 second, “OK” will appear on the screen, indicating it has
automatically saveed the current settings. The LCD screen will shut
off automatically 10 seconds later. Note: On the P (photo) setting, SmartGuard will take a series of digital photographs at a rate of 1-3 photos every second when the motion sensor is triggered
Start
YEAR
Setting
③ MONTH
Setting
DATE
Setting
HOUR Setting
MINUTE
Setting
VIDEO/
PHOTO
Setting
Finish
11
Step 5. Viewing video
1. Viewing image by computer through a card reader (see fig. 13)
Open the waterproofed cover on the Smartguard Motion Light
with Video Camera
Press OFF/REC button and remove memory card (part no.)
from the slot.
Put the memory card (part no.) into a card reader, connect
card reader to computer, and open any media player to view any videos or photos.
Fig. 13
12
Technical Specifications
Features and specification
PIR detection angle 180 Deg and detection range up to 32.8ft Records 20 seconds image recording for image stream:
10fps at 720P (HD)
Built in memory card slot for memory card Memory card slot for additional storage, max memory size up
to 32GB
Memory card spec.: FAT16SD)、FAT32SDHC Automatic exposure control, white balance and sharpness Auto Date & Time stamp Effective viewing angle60 deg Effective viewing distance: 26.24 feet Image format: JPEG AVI File Powered by AC 100V to 240Vsubject to requirement Auto light sensor. Sensitivity control Floodlight time delay control
13
General Information and safety
Special care instructions!!!
The Smartguard Motion Light with Video Camera is designed to be
weather resistant. Never attempt to immerse the unit in water or any other liquid. This will damage the unit and void the warranty.
This product is designed to illuminate, video, and make verbal
announcements. It will not prevent the commission of any act, legal or illegal. The manufacturer assumes no liability for any damage to property, injury to person, or death.
Use a soft lens cloth for cleaning lens. Avoid touching lens with
fingers.
Remove dirt or stains with a soft cloth dampened with water or
neutral detergent. Keep the Smartguard Motion Light with Video Camera in a dry and cool dust-free environment or container when it is NOT used
Do not open the Smartguard Motion Light with Video Camera for
unauthorized service. This could cause serious damage to the unit and will void the warranty.
This Smartguard Motion Light with Video Camera is a precision
electronic device. Do not attempt to service this camera yourself, as opening or removing covers may expose you to the danger of electric shock or other risks.
14
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modification to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limited for Class B digital device, pursuant to Part 15 of the FCC Rules. Their limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
15
FAQ (Frequently Asked Questions) Section
Q. How many pictures does the memory card hold?
A: The number of video files that amount to memory card varies, as the size in bytes of each 20-second video clip will vary depending on the amount of brightness, color, and movement in each video clip. The clips typically vary from 8MB to 16MB.
Memory Card
File Size (min.)
Qty of File(approx.)
1G
8Mb
125
2G
8Mb
250
32G
8Mb
4000
Q. What happens when the card is full?
A: SmartGuard will automatically return to the oldest file and save over it each time a new video clip is stored. That means you don’t have to take out the memory card unless you wish to review or save the video files.
Q. Can I transfer pictures from the camera via cable?
A: No, you can’t. If your computer has an memory card slot, you may insert the memory card directly into the computer and access the files by going to My Computer and opening the removable for the memory card, which should appear when you insert the card. See Step. 5Viewing video in your instruction manual for details. If you don’t have an memory card slot, you may purchase an memory card reader from any retailer that sells electronics. Once you have an memory card reader, simply insert the card into the reader and attach the reader to your computer using a USB slot (not included in this packaging), and access the data the same way as explained above.
Q. Can I view a live image of what the camera sees?
A: No, you cant. There is no USB port available with SmartGuard.
Loading...