Smart Digital Smart Mix SDM200 User Manual

USER MANUAL
USER PRECAUTIONS
PRODUCT FUNCTION DESCRIPTION
FRONT PANEL FUNCTION DESCRIPTION
PRODUCT CONNECTION DIAGRAM
PRODUCT CONNECTION DIAGRAM
PERFORMANCE SPECIFICATION PARAMETER
3
5
5
6
7
8
2
User Precautions
1.1 This product has AC110V/AC240V transfer switch.
Please conrm the supply voltage of the power grid before
using, pull the switch out to match the supply voltage of the
power grid. This product uses power plug and device appliance
coupler as disconnecting device of power supply in
power grid. When broken, it is fully disconnected power
supply and product electrodes. Convenient operation
should be maintained when using power plugs or device
appliance couplers.
1.2 In order to eectively protect this product, please use it
safely, and pay attention to the following:
1.2.1 Do not place bare ame sources, such as lighted candles,
on this product.
3
User Precautions
1.2.2 Before use of equipment,
1) Please check that the power cord should not be damaged, Matching use of power plug and power socket connecting power grid, If it does not match, please replace the appropriate power socket in time. No man-made destruc­tion, modication and use shall be allowed.
2) The power supply of this product should be the same as the voltage of the transfer switch, and the grounding wire is independent and reliable.
3) The most suitable working environment for this product is temperature: 5-28°, relative humidity is less than 90%. If the working time is long and the ambient temperature is too high, eective cooling measures are recommended.
4) The power supply specications required by this product are AC110V/60Hz or AC240/50Hz. If the voltage of the power grid varies from high to low, and the uctuation is relatively large, it is recommended to install the AC regulated power supply device.
5) Before turning on the power supply, the volume switch must be set to a minimum. After turning on, the vol­ume switch should be slowly increased to prevent the instan­taneous signal voltage shock from damaging the loudspeak­er.
6) Before turning o the power supply, the volume switch should be set to a minimum.
4
Product Function Description
2.1 Front panel diagram:
1) Installation Hole
2) Power Indicator Lamp
3) Remote Control Receiving Window
4) HDMI Selection Switch and Channel Indicator
5) Power Switch
6) Microphone Input 1 XLR Interface
7) Microphone Volume Adjustment Knob
8) AUX3.5 Input and Volume Adjustment Knob
9) HDMI Volume Adjustment Knob
10) Bass and Treble Adjustment knobs
11) Master Volume Adjustment Knob
12) 3.5 Interface Headphone Monitor Output and Monitor
Volume Adjustment Knob
13) Bluetooth Switch and Bluetooth Status Indicator. The light
is o means the it is turned o, when the light ashes it is in
searching, and the light is long on means it is connected.
14) USB Impulse Interface, Impulse Voltage 5V/1A
5
Product Function Description
2.2 Back panel diagram:
1) HDMI Input Interface
2) HDMI Output Interface
3) Microphone Input 2-4 XLR Interface
4) Left and Right Channel Output Interface
5) Bluetooth Antenna Interface
6) AC110V/AC240V Transfer Switch
7) Power Input Interface
6
Product Connection Diagram
7
Performance Specication Parameter
Equipment Model SDM200
MIC Input Sensitivity(MIC1/MIC2/MIC/
MIC4)
Line Input (AUX) 10k ohms(Ω) 300mV, Un-balanced
Audio Signal Output (MAIN OUTPUTS) 10k ohms(Ω) 0.775V (0 dB), Balanced(L/R)
Monitor Signal Output (HEADPHONE) 10k ohms(Ω) 0.775V (0 dB), Un-balanced
Frequency Response 50Hz~18kHz(±3dB)
Nonlinear Distortion THD <0.05% at 1kHz
Signal-to-Noise Ratio(S/N) >70 dB
Tone Adjustment Range BASS:100Hz(±10dB) , TREBLE:10kHz(±10dB)
Power Input AC110V-AC240 Switchable 50-60Hz
Power Consumption 45W
600 ohms(Ω) 5mV, Balanced
8
Loading...