Smart Avi XTWALL User Manual

Technical Specifications

© Copyright 2008 Smart-AVI, All Rights Reserved

XTWALL SPECIFICATIONS

VGA Data

Format RGBHV, RGsB, YUV, Y/C, CVBS

Resolution

Connector type HD 15 socket

Audio

Signal Type Stereo unbalanced

Connector 3.5mm jack socket

Power

Requirements 5VDC @.5A

Connector 2.1mm DC jack (center +ve)

Physical

Dimensions 135 x 90 x 23mm (26 with pegs)

Weight .8 lbs or .36 kg

Up to 1900 x 1200
VGA, SVGA, XGA, SXGA

Recieve on DB9 Male

Notice

The information contained in this document is
subject to change without notice. Smart-AVI makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties
of merchantability and fitness for any particular
purpose.

Smart-AVI will not be liable for errors contained
herein or for incidental or consequential damages
in connection with the furnishing, performance or
use of this material.

No part of this document may be photocopied,
reproduced or translated into another language
with
out prior written consent from Smart-AVI.

For the complete manual, visit www.smartavi.com.

Attaching the Power Supply

SMART AUDIO VIDEO INNOVATION

User Manual

XTWALL

Pin No. Name Description

2 RxD Receive Data on DB9 Male

3 TxD Transmit Data on DB9 Male

5 SGND Ground

Transmit on DB9 Female

Pin No. Name Description

2 TxD Transmit Data on DB9 Female

3 RxD Recieve Data on DB9 Female

5 SGND Ground

Insert black wire into the positive input (left) and 1.
secure.
Insert white wire into the negative input (right) 2.
and secure.
Plug into outlet.3.

2840 N. Naomi Ave.

Burbank, California 91504

Phone: [phone]

Facsimile: [phone]

Use a single CAT5 to broadcast high

resolution SXGA, Stereo Audio, RS232

and IR up to 1000ft away.

www.smartavi.com

Introduction

The XTWALL allows the extension of a wide range of
video and audio formats, RS232, and IR via a sing

Category 5 Unshielded Twisted Pair (UTP) cable.

Features

 Supports Dual Screens.
 Uses easy to install, inexpensive CAT-5/5e/6/7/8.

 Output reaches up to 1,000 feet (300 m).

 Resolutions up to 1900x1200.
 300 MHz Bandwidth.
 Sends high-resolution UXGA, Stereo Audio and
 Compatible with Line Level Stereo Audio Signals.
 High ground loop immunity.
 Built-in lightning, power surge and transient

protection.

 Designated trimmer in the remote unit to

compensate for cable length.

 Compact Metal Case Enclosure.

 Supports RS232 and IR

Installation Diagram

XTWALL Transmitter XTWALL Receiver

Connecting The Transmitter

Adjusting and Tuning the Signal

What’s in the box?

XTPRO

Please check the contents of the package before
beginning installation.

XTWALL Package Content

Qty Items Part No.

1 XTWALL Transmitter unit

1 XTWALL Receiver unit

2 5 volt dc power supply

HDD 15 male to male VGA

1

cable (6ft)

Optional

Audio 3.5 mm stereo mini-

1

plug cable

1 IR EYE Receiver

1 IR Emitter

1 Serial m/f DB9 6ft.

XTW-TX

XTW-RX

PS5D1AW-US

CC-VGAMM-06

CC-ADMM06

SM-EYE

SM-LED

CCSERMF06

1. Connect the output of the computer video card to the
video input of the transmitter using the included male
to male video cable.

2. Connect the output of the computer audio card to
the audio input of the transmitter using 3.5mm audio
male to male audio cable.

3. Connect local monitor to the VGA out of the

transmitter.

4. Connect external speakers to the transmitter’s audio
out (Standard 3.5mm stereo miniplug).

5. In the back of the unit connect the CAT5 cable that
will connect to the receiver (XTW-RX).

*NOTE: You can not use RS232 and IR at the same time.

Connecting The Receiver

1. Connect CAT5 cable (coming from the transmitter) to
the back of the receiver.

2. Connect 1-2 display monitors to the VGA out
connectors on the front of the receiver.

3. Connect 1-2 sets of external speakers to the audio
output connections on the front of the unit.
(Standard 3.5mm stereo Miniplug)

In order to fine tune the signal, adjust the individual
dials one at a time starting with GREEN, then BLUE,
and lastly RED. As you turn the dials you will notice the
colors slightly change as you increase or decrease the
strength. All dials should be around the same distance.

Blue Green Red

Preparing & Connecting System CAT5 Cable

Following is the wiring standard for terminating CAT 5 cable
using RJ-45 connector:

Pair 1 Pins 1 & 2
Pair 2 Pins 3 & 6
Pair 3 Pins 4 & 5
Pair 4 Pins 7 & 8

Connectors: RJ-45
Capacitance: 14 pf/ft (46.2 pf/m)
Conductor Gauge: 24 AWG
Impedance: 100 +/- 15 ohms
4 - Pair